Electrical Engineering › Section K · Methods of analysis and theorems (ac) › Topic K.4

Thevenin and Norton (ac)

Seen from two terminals, any linear ac network, however tangled, behaves like one source and one impedance. Thevenin's and Norton's theorems find that pair, so a load can be changed and re-solved in a single line, and they are how engineers describe the output of every amplifier and signal source.

A whole network as one source

"Thevenin's theorem" and "Norton's theorem" showed that any linear dc network, viewed from two terminals, can be replaced by a voltage source with a series resistance, or by a current source with a parallel resistance. The ac versions say the same with phasors and impedances. A linear ac network seen from terminals a and b is equivalent to a voltage source \(\mathbf{E}_{Th}\) in series with an impedance \(Z_{Th}\), or to a current source \(\mathbf{I}_N\) in parallel with \(Z_N = Z_{Th}\). The equivalent holds at one frequency, because the reactances inside change with frequency. Bold letters are rms phasors.

Finding the Thevenin equivalent

When the network contains only independent sources, follow three steps. 1. Remove the load, leaving terminals a and b open. 2. Find \(Z_{Th}\): zero every independent source (voltage sources shorted, current sources opened, internal impedances kept) and work out the impedance seen looking into a and b. 3. Find \(\mathbf{E}_{Th}\): restore the sources and find the open-circuit voltage between a and b, usually with the voltage divider rule, superposition or nodal analysis. The equivalent then gives the current in any load directly:

\mathbf{I}_L = \frac{\mathbf{E}_{Th}}{Z_{Th} + Z_L}

Worked example: a Thevenin equivalent

Source \(\mathbf{E} = 20\angle 0^\circ\) V has + at node a and − at ground. A 6 Ω resistor joins a to node b, a capacitive reactance of 8 Ω joins b to ground, and an inductive reactance of 4 Ω joins b to terminal x. The output terminals are x and ground. 1. Source shorted: 6 Ω and \(-j8\,\Omega\) are in parallel, \(3.84 - j2.88\,\Omega\), in series with \(j4\,\Omega\), so \(Z_{Th} = 3.84 + j1.12\,\Omega = 4\angle 16.3^\circ\,\Omega\). 2. Open circuit: no current flows in the \(j4\,\Omega\), so

\mathbf{E}_{Th} = \frac{(-j8)(20\angle 0^\circ)}{6 - j8} = 16\angle -36.9^\circ\,\text{V}

3. With a 5 Ω load: \(\mathbf{I}_L = 16\angle -36.9^\circ / (8.84 + j1.12) = 1.80\angle -44.1^\circ\) A, which a full solution of the original network confirms.

The Norton equivalent

The Norton equivalent replaces the network with a current source \(\mathbf{I}_N\) in parallel with \(Z_N\). The impedance is found exactly as for Thevenin, so \(Z_N = Z_{Th}\). The source current is the short-circuit current: join a and b with a wire and find the current through it. Because the two equivalents describe the same network, they convert into each other by source conversion:

\mathbf{I}_N = \frac{\mathbf{E}_{Th}}{Z_{Th}}, \quad \mathbf{E}_{Th} = \mathbf{I}_N Z_N

Norton's form is the natural one when the load will be in parallel with other branches, since admittances then simply add.

Worked example: the Norton form

Find the Norton equivalent of the previous network at terminals x and ground. 1. By conversion: \(\mathbf{I}_N = 16\angle -36.9^\circ / 4\angle 16.3^\circ = 4\angle -53.1^\circ\) A, in parallel with \(Z_N = 4\angle 16.3^\circ\,\Omega\). 2. Check directly by shorting x to ground. The \(j4\,\Omega\) and \(-j8\,\Omega\) are then in parallel, \(j8\,\Omega\), so the source sees \(6 + j8 = 10\angle 53.1^\circ\,\Omega\) and supplies \(2\angle -53.1^\circ\) A. 3. The current divider sends

\mathbf{I}_{sc} = \frac{(-j8)(2\angle -53.1^\circ)}{-j8 + j4} = 4\angle -53.1^\circ\,\text{A}

through the short, matching step 1. Notice that this short-circuit current is larger than the source current, a sign of partial cancellation between the two reactances.

Networks with dependent sources

Dependent sources change step 2, because they cannot be zeroed. If a dependent source's controlling variable lies outside the part being simplified, the usual method still works. Otherwise use one of two methods. Method 1: find the open-circuit voltage \(\mathbf{E}_{oc}\) and the short-circuit current \(\mathbf{I}_{sc}\) with all sources active, then \(Z_{Th} = \mathbf{E}_{oc}/\mathbf{I}_{sc}\). Method 2: zero only the independent sources, apply a test voltage \(\mathbf{V}_o\) to the terminals, find the current \(\mathbf{I}_o\) it drives in, and take \(Z_{Th} = \mathbf{V}_o/\mathbf{I}_o\). Method 2 is the only choice when the network has no independent sources, since then \(\mathbf{E}_{Th} = 0\).

Worked example: a dependent source

Source \(\mathbf{E} = 12\angle 0^\circ\) V drives current \(\mathbf{I}_1\) through 2 kΩ into terminal a. A dependent source pushes \(3\mathbf{I}_1\) into a, and a capacitive reactance of 2 kΩ joins a to ground. 1. Open circuit: the capacitor carries \(4\mathbf{I}_1\), so \(4(12 - \mathbf{V})/2000 = \mathbf{V}/(-j2000)\), giving \(\mathbf{E}_{oc} = 48/(4 + j) = 11.6\angle -14.0^\circ\) V. 2. Short circuit: the capacitor is shorted, \(\mathbf{I}_1 = 6\) mA and \(\mathbf{I}_{sc} = 4\mathbf{I}_1 = 24\angle 0^\circ\) mA. 3. Impedance: \(Z_{Th} = 11.6\angle -14.0^\circ / 0.024 = 485\angle -14.0^\circ\,\Omega\). 4. Check with a test source: it gives \(2000/(4 + j)\), the same 485 Ω, because the dependent source makes the 2 kΩ look four times smaller.

Measuring and using an equivalent

The same ideas work on a bench. The open-circuit voltage of a real signal source can be measured with a high-impedance voltmeter. Its internal impedance can then be found by adding a known load and watching the terminal voltage drop, or by finding the load that halves the open-circuit voltage, which works when that load has the same angle as \(Z_{Th}\). Engineers quote the output impedance of generators, amplifiers and sensors for exactly this reason: once you know \(\mathbf{E}_{Th}\) and \(Z_{Th}\), the effect of any load is a one-line calculation. The next topic, "Maximum power transfer and other theorems (ac)", uses the equivalent to choose the best load.

Common mistakes to avoid

1. Leaving the load in place while finding \(Z_{Th}\) or \(\mathbf{E}_{Th}\). 2. Forgetting an impedance that carries no current on open circuit, such as the \(j4\,\Omega\) above: it adds nothing to \(\mathbf{E}_{Th}\) but is part of \(Z_{Th}\). 3. Zeroing a dependent source when finding \(Z_{Th}\). 4. Using the equivalent at a different frequency from the one it was found at. 5. Writing \(\mathbf{I}_N = E_{Th}/|Z_{Th}|\) and losing the angle. 6. Applying a test source while leaving the independent sources active.

Key takeaways

A linear ac network seen from two terminals equals \(\mathbf{E}_{Th}\) in series with \(Z_{Th}\), or \(\mathbf{I}_N\) in parallel with \(Z_N = Z_{Th}\), at one frequency. With independent sources only, \(Z_{Th}\) is the impedance seen with the sources zeroed and \(\mathbf{E}_{Th}\) is the open-circuit voltage. \(\mathbf{I}_N\) is the short-circuit current, and \(\mathbf{I}_N = \mathbf{E}_{Th}/Z_{Th}\). With dependent sources, use \(Z_{Th} = \mathbf{E}_{oc}/\mathbf{I}_{sc}\) or a test source with the independent sources zeroed. The load current is \(\mathbf{E}_{Th}/(Z_{Th} + Z_L)\).

Flashcards

Flashcard

Thevenin's theorem (ac)

A linear network at two terminals equals E_Th in series with Z_Th

Valid at one frequency.

Test your understanding

Question 1 of 5

A source of 30∠0° V has a 3 Ω series resistor, then an inductive reactance of 4 Ω across the output terminals. What is E_Th?

Question 2 of 5

For the same network (30∠0° V, 3 Ω in series, inductive 4 Ω across the terminals), what is Z_Th?

Question 3 of 5

A Thevenin equivalent has E_Th = 10∠0° V and Z_Th = 4 + j3 Ω. What is the Norton current?

Question 4 of 5

A network with a dependent source has an open-circuit voltage of 8∠0° V and a short-circuit current of 2∠−30° A. What is Z_Th?

Question 5 of 5

A network contains only a dependent source and impedances, with no independent source. How do you find its Thevenin impedance?

← Previous topicNext topic →