Electrical Engineering › Section H · Magnetic circuits and inductors › Topic H.4
Faraday's and Lenz's laws
A changing magnetic flux through a coil produces a voltage across it. Faraday's law says how big that voltage is, and Lenz's law says which way it acts. Together they explain generators, transformers, microphones and the behaviour of every inductor.
From current to field, and back again
Oersted had shown that a current makes a magnetic field. In about 1831 Michael Faraday found the reverse link: a magnetic field can make a voltage, but only while the flux through a circuit is changing. A magnet held still inside a coil does nothing; the same magnet pushed in or pulled out makes a meter on the coil kick. This is electromagnetic induction, the basis of generators, transformers and inductors.
Faraday's law
For a coil of \(N\) turns, all linked by the same flux \(\Phi\), the induced voltage is
Linked means passing through the turns. The voltage depends on how fast the flux changes, not on how large the flux is. When the change is steady, or when only the average is wanted, use \(e = N\,\Delta\Phi / \Delta t\). Since \(\Phi = BA\cos\theta\), the flux can change in three ways: the flux density changes, the area inside the circuit changes, or the angle changes as the coil turns. If none of these happens, \(d\Phi/dt = 0\) and no voltage is induced, however strong the field.
Worked example: a changing field
A 250-turn coil of area \(3.0 \times 10^{-3}\,\text{m}^2\) sits face-on to a field that rises steadily from 0.10 T to 0.45 T in 20 ms. Find the induced voltage. 1. Change in flux per turn: \(\Delta\Phi = 0.35 \times 3.0 \times 10^{-3}\), which is \(1.05 \times 10^{-3}\,\text{Wb}\). 2. Faraday's law:
rounded to three significant figures. 3. Check: make the same change in 2.0 ms, ten times faster, and the voltage is ten times larger, 131 V. The 0.10 T already present adds nothing on its own; only the change counts.
A conductor cutting flux
Faraday's law also covers a conductor moving through a field. Picture a straight rod of length \(l\) sliding at speed \(v\) along two rails, at right angles to a uniform field \(B\), with the rails joined at one end to close the circuit. Each second the rod sweeps an extra area \(lv\), so the flux through the circuit grows at the rate \(Blv\), and the induced voltage is
A 0.30 m rod moving at 5.0 m/s across a 0.80 T field gives \(0.80 \times 0.30 \times 5.0 = 1.2\,\text{V}\). Moving the field instead of the rod gives the same result: only relative motion matters.
Lenz's law
Heinrich Lenz stated the direction rule in about 1834: an induced effect always acts to oppose the change that produced it. If the flux through a coil is rising, the induced current flows so that its own flux points against the rise; if the flux is falling, the induced current tries to prop it up. It opposes the change, never the flux itself. This is energy conservation: if the induced current helped the change, a nudge would grow without limit and give energy for nothing. Because the coil fights back, work must be done to change the flux, and that work becomes electrical energy.
Finding the direction: three steps
1. Find the direction of the flux through the coil and decide whether it is increasing or decreasing. 2. The induced flux points opposite to the original if it is increasing, and the same way if it is decreasing. 3. Use the right-hand rule for a coil: point your thumb along the induced flux, and your fingers curl in the direction of the induced conventional current. The end of the coil where the induced flux leaves acts as a north pole. A quick check: the coil always behaves as a magnet that resists the motion, repelling a magnet that approaches and attracting one that moves away.
Worked example: a magnet and a coil
A coil lies with its left face towards you. The north pole of a bar magnet is pushed towards that face. Find the induced current's direction as you see it. 1. The magnet's flux enters the left face, pointing away from you, and grows as the magnet approaches. 2. The induced flux must oppose the increase, so it points towards you, out of the left face. 3. Thumb towards you: the fingers curl anticlockwise. 4. Check: flux leaves the left face, so that face is a north pole, repelling the approaching north pole. Now pull the magnet away: the flux away from you is decreasing, the induced flux points away from you, and the current reverses to clockwise. The left face becomes a south pole, attracting the retreating magnet.
Signs in circuit work
Physics books often write \(e = -N\,d\Phi/dt\), where the minus sign stands for Lenz's law. In circuit analysis it is simpler to compute the size with \(e = N\,d\Phi/dt\) and to set the polarity using Lenz's law, then mark it with + and − on the diagram. The induced voltage behaves like a source inside the coil: if the coil's ends are joined through a resistor, current leaves the coil's + terminal. The topic "Self-inductance, inductor types, and induced voltage" applies this to a coil whose own changing current changes its flux.
Eddy currents
Induction does not need a wire. A changing flux in any solid conductor drives loops of current, called eddy currents, inside it. In a transformer or motor core they waste energy as heat, so cores are built from thin steel laminations, insulated from one another and running along the flux, which cut the eddy paths into narrow strips; the loss falls roughly with the square of lamination thickness. At high frequencies, poorly conducting ferrite cores are used instead. Eddy currents are also useful: an induction hob heats a steel pan directly, a magnet dropped down a copper tube falls slowly, and some trains brake with them.
Induction at work
A generator turns a coil in a field, changing the angle and so the flux. Turn a 100-turn coil of area 0.010 m² in a 0.50 T field from face-on to edge-on in 25 ms: the flux per turn falls by 5.0 mWb, so the average voltage is \(100 \times 0.0050 / 0.025 = 20\,\text{V}\). In a dynamic microphone, sound moves a light coil in a magnet's field, inducing a voltage that follows the sound wave. In a transformer, flux changing in one winding induces a voltage in a second winding on the same core.
Common mistakes to avoid
First, thinking a strong steady field induces a voltage: only change does. Second, forgetting the factor \(N\), or using flux density where the law needs flux. Third, saying the induced current opposes the flux; it opposes the change in flux. Fourth, applying \(e = Blv\) when the motion is along the field lines, which cuts no flux. Fifth, leaving times in milliseconds inside the formula. Sixth, assuming laminations raise permeability; they exist to block eddy currents.
Key takeaways
A changing flux through a coil induces \(e = N\,d\Phi/dt\), or \(N\,\Delta\Phi/\Delta t\) on average. The flux can change through \(B\), the area or the angle; a steady flux induces nothing. A conductor moving across a field gives \(e = Blv\). Lenz's law: the induced effect opposes the change that caused it, which is energy conservation. Find directions in three steps: flux direction, rising or falling, then the right-hand rule for the induced flux. Eddy currents waste energy in solid cores, so cores are laminated or made of ferrite.
Flashcards
Flashcard
A changing flux through a circuit induces a voltage
Test your understanding
Question 1 of 5
The flux through a 120-turn coil falls steadily from 2.0 mWb to 0.50 mWb in 30 ms. What is the size of the induced voltage?
Question 2 of 5
A 0.20 m rod slides at 3.0 m/s on rails, at right angles to a uniform 0.50 T field. What voltage is induced across it?
Question 3 of 5
The north pole of a magnet is pulled away from the face of a coil whose ends are joined. How does the coil respond?
Question 4 of 5
A coil sits at rest in a steady 1.5 T field, with its face at right angles to the field. What voltage is induced across it?
Question 5 of 5
Why are transformer cores built from thin, insulated steel laminations rather than a solid block?
