Electrical Engineering › Section Q · Thyristors, operational amplifiers, and power conversion › Topic Q.4

Single-ended, differential, and operational amplifiers

The operational amplifier is a packaged differential amplifier with enormous gain, and it is the most widely used building block in analogue electronics. This topic explains what it amplifies, why its gain is so high, and what it does with no feedback at all.

The amplifier as a triangle

Earlier topics built amplifiers from single transistors, as in Common-emitter, common-collector, common-base, and cascode amplifiers. Once a design works, schematics hide its insides behind a triangle: input on the wide side, output at the point, and supply leads +V and −V at top and bottom, often left off the drawing. Every signal voltage is measured from a shared reference node, ground. An amplifier with one input measured from ground is single-ended. The load's current comes from the power supply, not from the input signal; the input only controls how much of the supply reaches the output, as with the amplifier model in Input and output impedance, gains, and cascaded systems.

Split supplies

If a single 30 V supply powers an amplifier with its negative side as ground, the output can only range between about 0 V and 30 V, so a true ac output needs a coupling capacitor or transformer. A split, or dual, supply puts two sources in series and grounds the middle point, giving +15 V and −15 V. The amplifier still has 30 V in total, but now its output can swing above and below ground and drive an ac signal directly into a grounded load, and it can amplify dc signals of either polarity. Split supplies such as ±15 V and ±12 V are standard for differential amplifiers and op-amps.

Differential amplifiers

A differential amplifier has two inputs and amplifies only the difference between them:

V_{out} = A_V(V_+ - V_-)

The input marked + is the noninverting input: raising it drives the output positive. The input marked − is the inverting input: raising it drives the output negative. An ideal differential amplifier ignores any voltage the two inputs share; only their difference matters, much as a digital voltmeter reads only the voltage between its two leads. A quick sign rule: if the + input is the more positive of the two, the output is positive. Comparing two quantities this way, such as a measured process variable and its setpoint, is the first step in most automatic control.

Worked example: a differential amplifier

A differential amplifier has \(A_V = 5\) and a ±12 V supply. Find the output for four pairs of inputs. 1. Apply \(V_{out} = 5(V_+ - V_-)\) to each row:

\begin{array}{c|c|c} V_- & V_+ & V_{out} \\ \hline 0 & 0.5 & 2.5 \\ 1.2 & 0.7 & -2.5 \\ 2.0 & 2.0 & 0 \\ -0.4 & 0.6 & 5.0 \end{array}

2. Row 3: both inputs sit at 2.0 V, so the difference is zero and so is the output. 3. Row 4: the difference is \(0.6 - (-0.4) = 1.0\,\text{V}\). 4. Check: every output is well inside ±12 V, so none is clipped; an input difference of 3 V would ask for 15 V and saturate.

Why "operational"?

Before digital computers, analogue computers solved equations with voltages standing for quantities such as speed or force. Resistor networks and amplifiers multiplied and divided, and capacitors, whose current is \(i = C\,dv/dt\), provided the operations of calculus. Designers found that a differential amplifier with extremely high gain was the most adaptable part: by choosing a few external components, they could set almost any gain or function without changing the amplifier itself. These high-gain differential amplifiers performed mathematical operations, so they became operational amplifiers, or op-amps. Integrated op-amps arrived in the 1960s; the classic 741 appeared in 1968 and is still made.

The ideal op-amp

Analysis starts from an ideal op-amp with three properties: infinite open-loop gain \(A_{OL}\), infinite input impedance, so no current flows into either input, and zero output impedance, so the output voltage does not sag under load. Real parts come close. Open-loop gains of 100,000 to over 1,000,000 are normal; a 741's inputs draw well under a microamp, and op-amps with FET input transistors draw far less; output resistances are tens of ohms. The supply pins are still there even when a schematic omits them, and every output current ultimately comes from those supply rails. The next topics add feedback; Practical op-amp limits, models, and data returns to the imperfections.

Too much gain to use alone

That huge gain means a bare op-amp is almost never a linear amplifier. Suppose \(A_{OL} = 100{,}000\) and the output saturates at about ±11 V on a ±12 V supply. The input difference that just reaches saturation is

\frac{11\,\text{V}}{100{,}000} = 110\,\mu\text{V}

A tenth of a millivolt drives the output to one rail or the other, and stray offsets are often bigger than that. Most real outputs stop short of the supply rails, by roughly a volt or two for older bipolar designs and by millivolts for rail-to-rail types. Without feedback, then, an op-amp behaves as a switch that reports which input is higher.

The comparator

Used open-loop, an op-amp is a comparator: the output saturates high when \(V_+ > V_-\) and low when \(V_+ < V_-\). Feed a sensor signal to one input and a reference from a potentiometer to the other, and the output flips at the trip point, ready to light an LED, drive a transistor or relay, or sound a low-level alarm. Feed a sine or triangle wave to one input and a dc reference to the other, and the output becomes a rectangular wave. Moving the reference changes how long the output stays high in each cycle, its duty cycle. Varying the duty cycle with a control voltage is called pulse-width modulation (PWM).

Worked example: setting a duty cycle

A 5 V peak sine wave drives the noninverting input of a comparator, and a +2.5 V reference sits on the inverting input. What fraction of each cycle is the output high? 1. The output is high while \(5\sin\theta > 2.5\), that is \(\sin\theta > 0.5\). 2. That holds from \(\theta = 30^\circ\) to \(150^\circ\), a span of \(120^\circ\). 3. Duty cycle: \(120/360 = 33.3\%\). 4. With the reference at 0 V the span is \(180^\circ\), 50%; at −2.5 V it is \(240^\circ\), 66.7%. Check: lowering the reference keeps the output high for longer, as expected when the + input wins more of the time.

Bargraphs and flash converters

Several comparators can watch one signal at once. Give each a different reference, set by a chain of resistors across the supply, and connect the signal to all of their noninverting inputs. As the signal rises, the comparators switch on one after another, so the number of lit LEDs shows its level, like the segment meter on an audio mixer. The same arrangement, with many more comparators and logic to encode which ones are on, is the flash analogue-to-digital converter. It is the fastest type of converter because every comparator decides at the same instant.

Common mistakes to avoid

First, reversing the inputs: raising the − input drives the output negative, not positive. Second, thinking a differential amplifier responds to a voltage both inputs share: ideally only the difference is amplified. Third, expecting an op-amp without feedback to amplify linearly: about 0.1 mV saturates it. Fourth, assuming the output reaches the supply rails: many op-amps stop a volt or two short. Fifth, imagining the input signal powers the load: the output current comes from the supply rails.

Key takeaways

A triangle stands for an amplifier; single-ended amplifiers have one input measured from ground, and split supplies let outputs swing both ways. A differential amplifier gives V_out = A_V(V+ − V−), with + noninverting and − inverting. The op-amp, named for its job in analogue computers, is a differential amplifier with open-loop gain of 100,000 or more. The ideal op-amp has infinite gain, no input current and zero output impedance. Open-loop it is a comparator, used for alarms, square waves, PWM, bargraphs and flash converters.

Flashcards

Flashcard

Amplifier triangle

Schematic symbol for an amplifier: input on the wide side, output at the point

Supply leads are often left off the drawing.

Test your understanding

Question 1 of 5

A differential amplifier whose gain is 8 has 1.25 V on its noninverting input and 1.50 V on its inverting input. What is its output?

Question 2 of 5

An op-amp with an open-loop gain of 150,000 saturates at about ±13.5 V. Roughly what input voltage difference drives it into saturation with no feedback?

Question 3 of 5

A 10 V peak sine wave drives the noninverting input of a comparator, with +5 V on the inverting input. For what fraction of each cycle is the output high?

Question 4 of 5

Why were high-gain differential amplifiers first called operational amplifiers?

Question 5 of 5

What is the main advantage of powering an amplifier from a ±15 V split supply instead of a single 30 V supply?

← Previous topicNext topic →