Electrical Engineering › Section Q · Thyristors, operational amplifiers, and power conversion › Topic Q.10
Power supply circuits
Almost every electronic device needs a steady dc voltage that no battery or wall socket supplies directly. Power supplies make it in three main ways, unregulated, linear and switching, and the choice is a trade between cost, noise, size and efficiency.
What a power supply does
Every power supply has an input source at some voltage \(V_1\), such as the mains, a battery or a solar panel, a load that needs \(V_2\), and a converter between them. An unregulated, or brute-force, supply is just a transformer, rectifier and filter. A linear regulated supply adds a transistor in its active region that drops the excess voltage. A switching supply chops the power with transistors that are fully on or fully off and smooths the result. A ripple-regulated hybrid switches a transistor to top up a large capacitor between two set voltages.
The unregulated supply
The brute-force supply uses the rectifiers of Diode basics, meter checks, ratings, and rectifier circuits followed by a reservoir capacitor. The capacitor charges to the peak on each pulse and supplies the load in between, sagging by a ripple voltage. For a full-wave rectifier the capacitor recharges at twice the mains frequency, \(f_r = 120\,\text{Hz}\) on a 60 Hz supply, and for a load current \(I\) the peak-to-peak ripple is about
It is cheap, simple and efficient, but its output carries ripple and follows both the mains voltage and the load. The transformer's primary is on the mains: such circuits are built and serviced isolated and de-energised, never worked on live.
Worked example: a brute-force supply
A transformer gives 12.6 V rms to a bridge rectifier (two diode drops of 0.7 V) and a 2200 µF capacitor, feeding 0.50 A. 1. Secondary peak: \(12.6\sqrt{2} = 17.8\,\text{V}\). 2. Capacitor peak: \(17.8 - 1.4 = 16.4\,\text{V}\). 3. Ripple:
4. So the output swings between about 14.5 V and 16.4 V, averaging about 15.5 V. Check: doubling the capacitance would halve the ripple, and a half-wave rectifier, recharging 60 times a second, would double it. The formula slightly overstates ripple.
Judging a power supply
Several figures compare supplies. Efficiency is output power divided by input power; the rest becomes heat, which needs heat sinks and derating at high temperature, since many semiconductors are damaged at junction temperatures around 150 °C. Line regulation is how much the output changes as the input varies. Load regulation is how much it changes from no load to full load, often as \((V_{NL} - V_{FL})/V_{FL}\), as in Internal resistance and voltage regulation. Ripple rejection, in decibels, compares the mains-related ripple at the output with that at the input. Quiescent current runs the supply itself; output impedance and noise matter for fast or sensitive loads.
Shunt regulators
A shunt regulator sits in parallel with the load and diverts whatever current is not needed, keeping the voltage across the load fixed. The simplest is a series resistor and a Zener diode, as in Inductor commutating and diode switching circuits, and Zener diodes. The resistor must pass the full load current plus a minimum Zener current at the lowest input, so at light load and high input most of that current heats the Zener. A plain resistor divider is worse: its output sags with load and follows every input change. Shunt regulators therefore suit small loads, tens of milliamps or less, and voltage references.
Worked example: a Zener regulator
A 5.1 V Zener regulator must supply 0 to 50 mA from an input of 9 V to 15 V, keeping at least 5 mA in the Zener. 1. Largest resistor, at 9 V and full load: \(R \le (9 - 5.1)/0.055 = 70.9\,\Omega\); choose 68 Ω. 2. Worst Zener case, at 15 V and no load: \(I = 9.9/68 = 146\,\text{mA}\), so \(P_Z = 5.1 \times 0.146 = 0.74\,\text{W}\), and the resistor dissipates \(9.9^2/68 = 1.44\,\text{W}\). 3. Efficiency at full load: \(0.255\,\text{W}\) out against \(9 \times 0.0574 = 0.516\,\text{W}\) in, 49% at 9 V, but only 12% at 15 V. Check: at 9 V the Zener still keeps 7.4 mA, above its 5 mA minimum.
Series (linear) regulators
A series regulator puts a pass transistor between input and load, working in its active region like a variable resistor, so it draws little more than the load current. The simplest is an emitter follower about 0.7 V below a Zener reference. Better designs add an error amplifier: an op-amp compares a fraction of the output, from a divider \(R_1\) over \(R_2\), with a reference \(V_{ref}\) and drives the pass transistor until they match, so
which is the noninverting amplifier of Negative feedback and divided feedback with a power transistor added. Three-terminal regulator chips package all of this. The input must stay above the output by the dropout voltage, about 1 V to 3 V for standard parts and less for low-dropout (LDO) types.
Worked example: a linear 5 V rail
The brute-force supply above (14.5 V to 16.4 V, average 15.5 V) feeds a series regulator with \(V_{ref} = 2.5\,\text{V}\) and \(R_1 = R_2 = 10\,\text{k}\Omega\), delivering 0.50 A. 1. Output: \(2.5(1 + 10/10) = 5.0\,\text{V}\). 2. Headroom: the lowest input, 14.5 V, is far above 5 V plus a 2 V dropout, so the ripple is removed. 3. Pass-transistor dissipation: about \((15.5 - 5.0)(0.50) = 5.2\,\text{W}\), needing a heat sink. 4. Efficiency: \(5.0/15.5 = 32\%\), ignoring quiescent current. Check: linear regulators are quiet and simple, but with a large input-to-output gap most power becomes heat.
Switching supplies
A switching regulator uses a transistor as a fast on-off switch and an inductor and capacitor to smooth the pulses, so in principle it wastes little power. The fraction of each cycle the switch is on is the duty cycle \(D\), from Pulse waveforms, repetition rate, duty cycle, and average value. Ideally a buck converter steps voltage down, \(V_{out} = DV_{in}\), and a boost converter steps it up, \(V_{out} = V_{in}/(1 - D)\); feedback adjusts \(D\) to hold the output. Switching at tens of kilohertz to megahertz keeps magnetics small, and efficiencies above 90% are common. Off-line switchers rectify the mains and chop it through a small high-frequency transformer, often accepting any mains voltage in the world. The costs are complexity, switching noise and some ripple.
Worked example: buck against linear
A 24 V bus must supply 5.0 V at 3.0 A. Compare an ideal-duty buck converter that is 90% efficient with a linear regulator. 1. Duty cycle: \(D = 5.0/24 = 0.208\). 2. Output power: \(5.0 \times 3.0 = 15\,\text{W}\). 3. Buck input: \(15/0.90 = 16.7\,\text{W}\), so 0.694 A from 24 V and 1.7 W of heat. 4. Linear: the load current flows straight through, so it draws 3.0 A at 24 V, 72 W, wasting 57 W, an efficiency of 21%. Check: the linear figure is just \(V_{out}/V_{in}\), while the buck draws less current from the input than it delivers, as an efficient step-down converter must.
Common mistakes to avoid
First, using 60 Hz in the full-wave ripple formula: it recharges at 120 Hz. Second, forgetting the diode drops in the capacitor's peak. Third, sizing a Zener resistor at the highest input voltage: it must still pass load plus minimum Zener current at the lowest input. Fourth, letting a linear regulator's input dip below output plus dropout at the ripple troughs. Fifth, expecting a linear regulator to step up or to be efficient with a large input-to-output difference.
Key takeaways
Power supplies are unregulated, linear, switching or ripple-regulated. A brute-force supply gives ripple V_r(pp) ≈ I/(f_r C), with f_r = 120 Hz for full-wave on 60 Hz mains. Supplies are judged on efficiency, heat, line and load regulation, ripple rejection, quiescent current, output impedance and noise. Zener shunt regulators suit small loads; series regulators set V_out = V_ref(1 + R₁/R₂), need dropout headroom and waste (V_in − V_out)I. Buck (V_out = DV_in) and boost (V_out = V_in/(1 − D)) converters switch at high frequency and often exceed 90% efficiency.
Flashcards
Flashcard
Unregulated: transformer, rectifier and filter capacitor only
Test your understanding
Question 1 of 5
A full-wave rectifier on 60 Hz mains feeds a 4700 µF reservoir capacitor and a 1.0 A load. About what is the peak-to-peak ripple?
Question 2 of 5
A linear regulator delivers 3.3 V at 0.80 A from a 12 V input. How much power does its pass element dissipate?
Question 3 of 5
An ideal buck converter must produce 12 V from a 48 V input. What duty cycle does it need?
Question 4 of 5
A 6.2 V Zener regulator must supply up to 30 mA from an input that can fall to 10 V, keeping at least 5 mA in the Zener. What is the largest series resistance allowed?
Question 5 of 5
A supply's output is 5.10 V with no load and 5.02 V at full load. What is its load regulation, as (V_NL − V_FL)/V_FL?
