Statics › Section B · Forces and other vectors › Topic B.5

Adding forces

A crane hook, a bridge joint or a tent peg usually feels several forces at once, and what matters is their combined effect. This topic collects the methods for adding forces, from quick sketches to the component method that works for any number of forces in two or three dimensions.

Combining forces

The vectors being added are called the components of the sum, and the sum itself is the resultant: the single force with the same effect as all of them together. There are several ways to find it, and each is a tool for a different job. Sketches show roughly where the resultant points, trigonometry gives exact answers for two forces, and components handle any number of forces in two or three dimensions. The physics topic "Two-dimensional motion and adding vectors" introduced these ideas for displacements and velocities; here they are applied to forces, where getting the resultant right is the first step towards equilibrium.

Triangle and parallelogram rules

Every method rests on tip-to-tail addition, met in the topic "Scalars and vectors". For two forces there are two equivalent pictures. In the triangle rule, place the tail of the second force at the tip of the first; the resultant runs from the first tail to the second tip. In the parallelogram rule, draw both forces from the same point and complete the parallelogram with lines parallel to each; the resultant is the diagonal from the shared tails to the opposite corner. Either force may go first, because addition is commutative, and the two rules always give the same resultant.

Graphical addition

If you draw the triangle or parallelogram accurately to scale, you can measure the resultant's length with a ruler and its direction with a protractor. The answer is only as precise as the drawing, so the method suits rough checks rather than final answers, unless you draw with CAD or geometry software. On paper it is also limited to forces in one plane. Even so, a quick sketch is always worth making: it shows roughly how big the resultant is and which quadrant it points into, which is exactly what you need to catch a wrong sign or a misread calculator angle later.

Trigonometric addition

A quick sketch of the force triangle can be solved exactly with the laws of cosines and sines. If forces \(P\) and \(Q\) form two sides and \(\gamma\) is the angle between those sides inside the triangle, then

R^2 = P^2 + Q^2 - 2PQ\cos\gamma \qquad \frac{\sin\alpha}{Q} = \frac{\sin\gamma}{R}

where \(\alpha\) is the angle between \(R\) and \(P\). The interior angle \(\gamma\) is 180° minus the angle between the two forces drawn tail to tail. The method has limits: it adds only two forces at a time, and it gives sizes and angles, not components, so for three or more forces the component method is better.

Worked example: two cables on a hook

Two cables pull on a hook: 400 N along the positive x axis and 250 N at 50° counterclockwise from it. Find the resultant. 1. Sketch the triangle: tip to tail, the interior angle between the two sides is \(\gamma = 180^\circ - 50^\circ = 130^\circ\). 2. Law of cosines:

R^2 = 400^2 + 250^2 - 2(400)(250)\cos 130^\circ = 351{,}058

so \(R = 592.5\) N. 3. Law of sines: \(\sin\alpha = 250\sin 130^\circ / 592.5\), giving \(\alpha = 18.9^\circ\). 4. The resultant is 592.5 N at 18.9° above the x axis. 5. Check: it lies between the two cables, nearer the larger one, as the parallelogram suggests.

Resolving into components

Running the parallelogram rule backwards splits one force into two components whose parallelogram has the force as its diagonal. This is called resolving the force. Any two directions would do, but perpendicular components are the most useful, because the parallelogram becomes a rectangle and the components are found with simple trigonometry, as in the topic "2D vectors and components". You can resolve along the usual x and y axes or along rotated axes x′ and y′:

\mathbf{F} = F_x\mathbf{i} + F_y\mathbf{j} = F_{x'}\mathbf{i}' + F_{y'}\mathbf{j}'

The components differ, but the force, and any resultant built from it, is the same.

Adding by components

The component method replaces vector addition with ordinary arithmetic. 1. Resolve every force into x and y components, with signs. 2. Add all the x components, then all the y components. 3. Rebuild the resultant from those sums. In symbols,

\mathbf{R} = \langle \Sigma F_x, \Sigma F_y, \Sigma F_z \rangle

The method works for any number of forces, and the third component is simply ignored in a plane. Because the x and y directions are independent, a vector equation in a plane splits into two separate scalar equations, so it can be solved for up to two unknowns.

Worked example: three forces on a bracket

A bracket carries 500 N at 30°, 300 N at 135° (both measured counterclockwise from +x) and 200 N straight down. Find the resultant. 1. Components: \(\langle 433.0, 250.0 \rangle\), \(\langle -212.1, 212.1 \rangle\) and \(\langle 0, -200 \rangle\) N. 2. Sums, in newtons:

R_x = 433.0 - 212.1 + 0 = 220.9
R_y = 250.0 + 212.1 - 200 = 262.1

3. Magnitude:

R = \sqrt{220.9^2 + 262.1^2} = 342.8\ \mathrm{N}

4. Direction: \(\tan^{-1}(262.1 / 220.9) = 49.9^\circ\), and both sums are positive, so no quadrant correction is needed. The resultant is 342.8 N at 49.9°.

Worked example: steering a barge

Two tugs pull a barge with ropes at 25° above and 35° below the positive x axis. What tensions give a resultant of exactly 1,200 N along +x? 1. Unknowns: \(T_1\) and \(T_2\). 2. x equation: \(T_1\cos 25^\circ + T_2\cos 35^\circ = 1200\). 3. y equation: \(T_1\sin 25^\circ - T_2\sin 35^\circ = 0\), since the resultant has no y part. 4. Solving: \(T_1 = 794.8\) N and \(T_2 = 585.6\) N. 5. Check: the y parts are both 335.9 N and cancel, and the x parts, 720.3 N and 479.7 N, add to 1,200 N. The rope nearer the x axis needs the larger tension.

Three dimensions and subtraction

In 3D the component method is unchanged, with z added. A pole top held by cables pulling \(\langle 0.6, -1.2, -1.2 \rangle\) kN and \(\langle -0.9, 0.4, -1.5 \rangle\) kN, and carrying a 2.0 kN downward load, feels \(\mathbf{R} = \langle -0.3, -0.8, -4.7 \rangle\) kN, a magnitude of 4.78 kN. This is the preferred 3D method, because angles in perspective drawings are easy to misread. To subtract, add the negative: \(\mathbf{A} - \mathbf{B} = \mathbf{A} + (-\mathbf{B})\), which in components means flipping the signs of B, then adding.

Common mistakes to avoid

First, using the angle between the forces in the law of cosines when the formula needs the interior angle of the triangle; with the minus sign, these differ by 180°. Second, adding magnitudes instead of components. Third, losing a sign when a component points left, down or along −z. Fourth, accepting a calculator angle without checking the quadrant against a sketch. Fifth, adding forces resolved along different sets of axes in one sum.

Key takeaways

The resultant is the single force equivalent to a set of forces. The triangle and parallelogram rules are the same tip-to-tail idea. Graphical addition gives estimates; the laws of cosines and sines give exact results for two forces, using the interior angle. The component method is the general tool: resolve each force, add the x, y and z components separately, then rebuild \(\mathbf{R} = \langle \Sigma F_x, \Sigma F_y, \Sigma F_z \rangle\). Any choice of axes gives the same resultant, and a planar vector equation gives two scalar equations, enough for two unknowns.

Flashcards

Flashcard

Resultant

The single force equivalent to a set of forces

Their vector sum.

Test your understanding

Question 1 of 5

Forces of 300 N along +x and 400 N along +y act on a ring. What is the resultant?

Question 2 of 5

Forces of 60 N and 80 N act from the same point, 60° apart. What is the magnitude of their resultant?

Question 3 of 5

What is the resultant of A = ⟨120, −50⟩ N, B = ⟨−40, 90⟩ N and C = ⟨−30, −10⟩ N?

Question 4 of 5

Two students add the same three forces, one using horizontal x axes and the other using axes along a ramp. What do they find?

Question 5 of 5

If A = ⟨3, 5, −2⟩ kN and B = ⟨−1, 4, 6⟩ kN, what is A − B?

← Previous topicNext topic →