Calculus › Section H · Applications of integrals › Topic H.7
Fluid pressure and force
Dive to the bottom of a pool and you feel the water press on your ears, harder the deeper you go. Pressure grows with depth, so a dam wall or a tank window cannot be designed from a single number: the deep parts take more force per square metre than the shallow parts, and the total force becomes an integral.
The push of water
Submerge your hand in a sink and you feel almost nothing; dive a few metres and your ears ache. Same fluid, different depths: the push — pressure — depends on how much water sits above you. This topic quantifies that push. Horizontal surfaces sit at a single depth, feel one constant pressure, and take a simple product. Vertical surfaces — dams, gates, portholes — span many depths at once, and totalling their force is the real job. The tool, once again, is slicing into strips.
Pressure and its laws
Pressure is force per unit area, measured in newtons per square metre. In a fluid at rest, the pressure at depth \(h\) is
where \(\rho g\) is the weight density of the fluid — about 9,800 newtons per cubic metre for water — and \(h\) is measured straight down from the surface. (This counts only the water's own pressure and ignores the atmosphere pressing on the surface.) Two laws make pressure manageable. Pressure depends only on depth, never on the shape or size of the container: the pressure 2 metres down in a thin tube of water equals the pressure 2 metres down in a lake. And at any given depth, pressure pushes equally in all directions — down, sideways, and up — which is why a diver's eardrums feel the squeeze from every side.
Force on a horizontal surface
When the surface is horizontal — the flat floor of a pool, say — every point of it sits at the same depth \(h\), so the pressure is one constant \(P = \rho g h\) across the whole area. Total force is then simple multiplication:
A pool floor 5 metres down with an area of 20 square metres takes \(9{,}800 \times 5 \times 20 = 980{,}000\) newtons. No integral is needed, and this is the check case: whenever a vertical-surface computation degenerates to constant depth, it must collapse back to this product.
Vertical surfaces: why an integral
A vertical window on a tank wall is different: its top edge sits at one depth and its bottom edge at a deeper one, so the pressure varies continuously across the plate. Slice the plate into horizontal strips of height \(dy\). The strip at depth \(y\) has width \(w(y)\) and area \(w(y)\,dy\); over that thin strip the depth — and so the pressure — is essentially constant, so the force on it is \(\rho g\,y \cdot w(y)\,dy\). Adding the strips:
where \(y\) runs from the depth of the top edge to the depth of the bottom edge, and \(w(y)\) is the plate's width at depth \(y\). The variable must be depth, not height above the floor — depth is what pressure understands.
Worked example: a rectangular floodgate
A rectangular floodgate is 2 metres wide and 4 metres tall, with its top edge at the water surface. Depth \(y\) runs from 0 to 4, and the width is constant: \(w(y) = 2\).
Check with the centroid shortcut below: the gate's area is 8 square metres, its centroid sits 2 metres down, and \(9{,}800 \times 8 \times 2 = 156{,}800\). For scale, that is about the weight of a 16-tonne load pressing on the gate.
Worked example: a triangular gate
A triangular gate has its base, 4 metres wide, at the water surface and its vertex 3 metres below. At depth \(y\), the triangle has narrowed linearly from 4 metres to 0, so \(w(y) = 4 - \tfrac{4}{3}y\).
Cross-check with the centroid shortcut: the triangle's area is \(\tfrac{1}{2}(4)(3) = 6\) square metres, and its centroid sits at the average of the vertex depths, \((0 + 0 + 3)/3 = 1\) metre down, giving \(9{,}800 \times 6 \times 1 = 58{,}800\) N. Two independent routes, one answer.
The centroid shortcut
Both checks used a general fact: the force on any flat vertical plate is
where \(A\) is the plate's area and \(\bar{d}\) is the depth of its centroid. The reason is that the integral \(\rho g\int y\,w(y)\,dy\) is, by definition, the moment of the plate's area about the surface line — and dividing a moment by area is exactly how centroids were located in the previous topic. For a rectangle, the centroid depth is half the height; for a triangle with base at the surface, it is one third of the vertex depth. The shortcut needs a flat plate, with the centroid measured in depth from the surface, and it is only a check: the integral is the method.
Why dams are thicker at the bottom
Dam walls are visibly wider at the base than at the crest, and pressure is the reason. Pressure grows linearly with depth, so the lowest part of the wall takes the greatest push per square metre, and the thick base is built to withstand it. Model the water face as a vertical wall of height \(H\) with water up to the top. Each metre of width is a rectangle with \(w(y) = 1\), so the force on it is
The force is quadratic in depth: doubling the water height quadruples the push. Holding back 20 metres of water, every metre of width takes \(9{,}800 \times 400 / 2 = 1{,}960{,}000\) newtons.
Common mistakes to avoid
The most common error is evaluating the pressure at one depth — usually the bottom, or the top — and multiplying by the whole area. That works for horizontal plates and fails for every vertical one: the pressure changes across the plate, so it must be integrated strip by strip. The second is measuring depth from the wrong zero: \(h\) is distance below the surface, not distance above the tank floor, so a plate whose top edge sits 2 metres down has \(y\) running from 2, not 0. The third is dropping the \(\rho g\) factor or mixing units: with \(\rho g = 9{,}800\) N/m³, depths and widths go in as metres and force comes out in newtons.
Key takeaways
Pressure is force per area: \(P = \rho g h\), depending only on depth and acting equally in all directions; for water, \(\rho g \approx 9{,}800\) N/m³. A horizontal surface takes constant pressure, so \(F = \rho g h A\). A vertical surface needs slicing: \(F = \rho g\int y\,w(y)\,dy\), with \(y\) the depth from the surface and \(w(y)\) the width at that depth. Equivalently, \(F = \rho g A\bar{d}\), with \(\bar{d}\) the centroid's depth. Dams are wide at the base because force grows with depth — a wall of height \(H\) takes \(\rho g H^2/2\) per metre of width.
Flashcards
Flashcard
Pressure at depth h
Test your understanding
Question 1 of 5
What is the water pressure at a depth of 3 metres (ρg ≈ 9,800 N/m³)?
Question 2 of 5
A square window, 1 m by 1 m, has its top edge 2 metres below the surface of a lake. What total force does the water exert on it?
Question 3 of 5
For any flat vertical plate, the total fluid force equals ρg times the plate's area times which depth?
Question 4 of 5
A triangular gate has its base, 6 metres wide, at the water surface and its vertex 4 metres below. What total force does the water exert on it?
Question 5 of 5
A diver's eardrums face sideways, yet they feel the full water pressure for their depth. Why?
Standards: Beyond AP
