Chemistry › Section I · Gases › Topic I.1
Gas pressure
A gas pushes on every surface it touches, from the inside of a tyre to your eardrums on a plane. Pressure measures that push, and getting its units right is the first step in every gas calculation that follows.
Why a gas pushes
Gas particles are far apart and in constant, rapid motion. Each one that strikes a wall bounces off and gives it a tiny shove, and so many strike every second that together they exert a steady, even force. Pressure is that force divided by the area it acts on:
The SI unit is the pascal, \(1\ \mathrm{Pa} = 1\ \mathrm{N\,m^{-2}}\). A pascal is small, roughly the push of a sheet of paper lying on a table, so gas pressures are usually given in kilopascals, kPa. The same force gives more pressure on a smaller area: a sharp knife concentrates your push, while snowshoes spread your weight.
Worked example: snowshoes and boots
A hiker of mass 65.0 kg stands on snow, either in boots with a total sole area of \(0.0500\ \mathrm{m^2}\) or in snowshoes with a total area of \(0.250\ \mathrm{m^2}\). Find the pressure on the snow each time. 1. Force is the hiker's weight: \(F = mg = 65.0 \times 9.81 = 637.7\) N. 2. Boots: \(P = \frac{637.7\ \mathrm{N}}{0.0500\ \mathrm{m^2}} = 1.28 \times 10^4\) Pa, or 12.8 kPa. 3. Snowshoes: \(P = \frac{637.7\ \mathrm{N}}{0.250\ \mathrm{m^2}} = 2.55 \times 10^3\) Pa, or 2.55 kPa. 4. Check: the snowshoe area is 5 times larger, so the pressure should be 5 times smaller, and \(12.75 \div 5 = 2.55\).
Atmospheric pressure
Earth's air has weight, and that weight presses down on everything beneath it. At sea level the atmosphere exerts about 101 kPa, which means roughly 10,300 kg of air sits above every square metre of ground. You are not crushed because the fluids in your body push outwards just as hard. With less air overhead, pressure falls with height: it is about half its sea-level value at 5.5 km and about a third on the summit of Mount Everest.
Units of pressure
Several units are in everyday use. The standard atmosphere is defined as exactly \(1\ \mathrm{atm} = 101.325\ \mathrm{kPa}\). The bar is defined as exactly \(1\ \mathrm{bar} = 100\ \mathrm{kPa}\), and weather maps use millibars, where 1 mbar equals 1 hPa. The torr is defined as exactly 1/760 of an atmosphere; the millimetre of mercury, mmHg, differs from it by less than one part in a million, so the two are used interchangeably. In the United States, tyres are measured in pounds per square inch, and 1 atm is about 14.7 psi.
Worked example: a mountain city's barometer
A barometer in a mountain city reads 635 mmHg. Express this in atm, kPa and bar. 1. To atm, use 760 mmHg = 1 atm: \(635\ \mathrm{mmHg} \times \frac{1\ \mathrm{atm}}{760\ \mathrm{mmHg}} = 0.836\) atm. 2. To kPa, use 1 atm = 101.325 kPa: \(0.8355\ \mathrm{atm} \times 101.325 = 84.7\) kPa. 3. To bar, use 100 kPa = 1 bar: \(84.66\ \mathrm{kPa} \div 100 = 0.847\) bar. 4. Check: the reading is below 760 mmHg, so every answer must be below 1 atm, 101 kPa and 1.01 bar, and they are.
The barometer
A barometer measures atmospheric pressure. The classic design is a glass tube, closed at one end, filled with mercury and inverted in a dish of mercury. The column falls until its pressure at the base balances the air pressing on the dish, leaving a near vacuum above it. The pressure at the bottom of a column of liquid of density \(\rho\) and height \(h\) is
At sea level the mercury stands about 760 mm high, which is where the mmHg unit comes from. Mercury is used because it is dense, about \(13.6\ \mathrm{g\,cm^{-3}}\), so the column stays a manageable length.
Worked example: a water barometer
How tall would a barometer column be at 1.00 atm if it used water, density \(997\ \mathrm{kg\,m^{-3}}\), instead of mercury? 1. Convert: \(1.00\ \mathrm{atm} = 1.013 \times 10^5\) Pa. 2. Rearrange \(P = \rho g h\): \(h = \frac{P}{\rho g}\). 3. Substitute: \(h = \frac{1.013 \times 10^5\ \mathrm{Pa}}{997\ \mathrm{kg\,m^{-3}} \times 9.81\ \mathrm{m\,s^{-2}}} = 10.4\) m. 4. Check another way: water is about \(13.6 \div 0.997 \approx 13.6\) times less dense than mercury, so its column is that many times taller, and \(0.760\ \mathrm{m} \times 13.6 = 10.3\) m, in agreement. This is also why a suction pump can never lift water more than about 10 m.
Manometers
A manometer measures the pressure of a trapped gas sample using a U-shaped tube of liquid, usually mercury. In a closed-end manometer the far arm is sealed with a vacuum above the liquid, so the difference in liquid levels, \(h\), gives the gas pressure directly: 25 mm of difference means 25 torr. In an open-end manometer the far arm is open to the air, so the gas is compared with atmospheric pressure. If the liquid stands higher in the open arm, the gas is pushing harder than the air and \(P_{\text{gas}} = P_{\text{atm}} + h\). If it stands lower in the open arm, \(P_{\text{gas}} = P_{\text{atm}} - h\).
Worked example: an open-end manometer
A flask of gas is attached to an open-end mercury manometer on a day when the barometer reads 755 torr. The mercury in the open arm stands 42 mm higher than in the arm joined to the flask. Find the gas pressure in torr and atm. 1. The open arm is higher, so the gas pushes harder than the air: \(P_{\text{gas}} = P_{\text{atm}} + h\). 2. With 1 mmHg = 1 torr: \(P_{\text{gas}} = 755 + 42 = 797\) torr. 3. Convert: \(797 \div 760 = 1.05\) atm. 4. Check: had the levels been equal, the gas would match the air at 755 torr; a higher open arm means more than that, as found.
Gauge pressure and blood pressure
Many instruments read gauge pressure, the amount by which a pressure exceeds atmospheric: a flat tyre still holds air at 1 atm, yet its gauge reads zero. A gauge showing 32 psi therefore means an absolute pressure of about \(32 + 14.7 = 46.7\) psi. Blood pressure is also a gauge reading, measured with a cuff called a sphygmomanometer and quoted in mmHg. A reading of 120/80 means the arterial pressure peaks 120 mmHg above atmospheric as the heart contracts (systolic) and falls to 80 mmHg above it between beats (diastolic). Gas laws always need absolute pressure.
Common mistakes to avoid
First, mixing units in one calculation, such as torr in one place and kPa in another; convert everything to a single unit first. Second, using 100 kPa for 1 atm: that is 1 bar, and the 1.3% difference shows up at three significant figures. Third, reversing the open-end manometer rule; ask whether the gas or the air is pushing the liquid harder. Fourth, putting a gauge reading straight into a gas-law calculation instead of adding atmospheric pressure. Fifth, forgetting that \(P = \rho g h\) needs SI units, density in \(\mathrm{kg\,m^{-3}}\) and height in metres, to give pascals.
Key takeaways
Gas pressure comes from particle collisions with the walls and is force per area, P = F/A, in pascals. Exact relationships: 1 atm = 101.325 kPa = 760 torr, with 760 mmHg the same for practical purposes, and 1 bar = 100 kPa. Atmospheric pressure is the weight of the air above, about 101 kPa at sea level and lower at altitude. A barometer balances a liquid column against the air, with P = ρgh. Manometers measure a trapped gas, directly when closed-end and relative to the air when open-end. Gauges read pressure above atmospheric.
Flashcards
Flashcard
Force per unit area: P = F ÷ A
Test your understanding
Question 1 of 5
A gas sample is at 1.50 atm. What is its pressure in kilopascals?
Question 2 of 5
A pressure of 380 torr is how many atmospheres?
Question 3 of 5
An open-end mercury manometer is used when the barometer reads 750 torr. The mercury in the open arm stands 25 mm lower than in the arm joined to the gas. What is the gas pressure?
Question 4 of 5
How would the column in a water barometer compare with the column in a mercury barometer at the same air pressure?
Question 5 of 5
A force of 450 N acts evenly on an area of 0.0150 m². What pressure does it exert?
