Chemistry › Section C · Composition of substances and solutions › Topic C.3
Molarity
Most laboratory reactions, and nearly all the chemistry in living things, happen in solution. Molarity tells you how many moles of a substance are packed into each litre, so you can measure out a known amount of it simply by measuring a volume.
Why measure by volume?
Weighing a solid is easy, but many reactions need their reactants dissolved so the particles can meet. Once something is dissolved, pouring or pipetting a volume is far quicker and more precise than weighing it again. A nurse sets up a saline drip by volume; a technician adds a reagent with a pipette. For any of that to work, you need to know how much substance is in each unit of volume, counted in moles because reactions are written in moles. That quantity is the solution's concentration, and the most widely used unit for it is molarity.
Solutions: the vocabulary
A solution is a homogeneous mixture of two or more substances. The substance present in the largest amount is usually called the solvent, and anything dissolved in it is a solute. When water is the solvent the solution is aqueous, shown by (aq) after a formula: \(\mathrm{NaCl(aq)}\) is salt dissolved in water. Concentration describes how much solute a given quantity of solution holds. A concentrated solution has a relatively large amount of solute; a dilute solution has relatively little. These two words are only comparisons, so a number with a unit is always better.
Defining molarity
Molarity, or molar concentration, is the amount of solute in moles divided by the volume of the whole solution in litres:
Its unit is mol/L (the same as \(\mathrm{mol/dm^3}\)), often written M and read "molar". Dissolving 0.300 mol of potassium chloride, KCl, to make 0.750 L of solution gives \(\frac{0.300\ \mathrm{mol}}{0.750\ \mathrm{L}} = 0.400\) M. The volume is that of the solution, not of the water used to make it. Because liquids expand slightly when warmed, a solution's molarity also changes slightly with temperature.
Making a solution properly
To make a solution of known molarity, weigh the solute, dissolve it in some of the solvent in a volumetric flask, then add more solvent until the bottom of the curved liquid surface sits on the etched mark. The flask then holds exactly its stated volume of solution. Simply adding solute to 1.00 L of water does not give 1.00 L of solution: dissolved particles change the volume, sometimes up and sometimes down. Mix thoroughly at the end, because a solution must be uniform before any sample taken from it has the stated concentration.
Worked example: concentration from a mass
Medical saline drips contain 9.00 g of sodium chloride, NaCl, in every 1.00 L of solution. What is the molarity? 1. Molar mass of NaCl: \(22.99 + 35.45 = 58.44\) g/mol. 2. Moles of solute: \(n = \frac{9.00\ \mathrm{g}}{58.44\ \mathrm{g/mol}} = 0.1540\) mol. 3. Molarity: \(c = \frac{0.1540\ \mathrm{mol}}{1.00\ \mathrm{L}} = 0.154\) M. 4. Check: 9 g is a little less than a sixth of 58 g, so a little less than 0.17 mol, consistent with 0.154. Three significant figures match the data.
Rearranging the definition
The same equation answers three kinds of question. Moles in a sample: \(n = c \times V\). Volume needed for a given amount: \(V = \frac{n}{c}\). Mass of solute: find \(n = cV\), then multiply by molar mass, \(m = nM\). Always convert millilitres to litres first, dividing by 1000. For example, how much 0.400 M KCl solution holds 0.0500 mol? \(V = \frac{0.0500\ \mathrm{mol}}{0.400\ \mathrm{mol/L}} = 0.125\) L, or 125 mL. Writing units at every step shows at once whether you multiplied or divided correctly.
Worked example: weighing out a solute
What mass of potassium permanganate, \(\mathrm{KMnO_4}\), is needed to make 250.0 mL of a 0.0200 M solution? 1. Volume in litres: \(250.0\ \mathrm{mL} = 0.2500\) L. 2. Moles needed: \(n = cV = 0.0200\ \mathrm{mol/L} \times 0.2500\ \mathrm{L} = 0.00500\) mol. 3. Molar mass: \(39.10 + 54.94 + 4(16.00) = 158.04\) g/mol. 4. Mass: \(m = nM = 0.00500 \times 158.04 = 0.790\) g. 5. Method: dissolve 0.790 g in a 250 mL volumetric flask and fill to the mark. 6. Check: a quarter-litre of 0.02 M holds 0.005 mol, and 0.005 of 158 g is about 0.8 g.
Dilution
Diluting a solution means adding solvent. The volume rises and the concentration falls, but the moles of solute do not change, because nothing is added or removed except solvent. Since \(n = cV\) before and after,
where 1 is the concentrated stock and 2 is the diluted solution. Any volume unit works if both sides use the same one, because the units cancel. \(V_2\) is the final total volume, not the volume of water added. For safety, when diluting a concentrated acid always add the acid slowly to the water, never water to the acid.
Worked example: preparing a dilute acid
A lab needs 500.0 mL of 0.300 M hydrochloric acid, HCl, and has a 6.00 M stock. How much stock is needed? 1. Write the dilution equation: \(c_1V_1 = c_2V_2\). 2. Rearrange: \(V_1 = \frac{c_2V_2}{c_1}\). 3. Substitute: \(V_1 = \frac{0.300\ \mathrm{M} \times 500.0\ \mathrm{mL}}{6.00\ \mathrm{M}} = 25.0\) mL. 4. Method: put about 400 mL of water in a 500 mL volumetric flask, add the 25.0 mL of stock, then fill to the mark. 5. Check: the concentration falls by a factor of \(\frac{6.00}{0.300} = 20\), so the volume must rise by 20, and \(25.0 \times 20 = 500\) mL.
Common mistakes to avoid
First, dividing by the volume of solvent rather than the volume of solution. Second, leaving volumes in millilitres when using \(n = cV\), which makes answers 1000 times too large. Third, treating M as the amount of solute: 0.10 M is a concentration, so the moles depend on the volume taken. Fourth, using the volume of water added as \(V_2\) in a dilution instead of the final total volume. Fifth, inverting the dilution equation: a diluted solution must always be less concentrated than its stock, so check that \(c_2\) is smaller than \(c_1\).
Key takeaways
A solution has a solvent and one or more solutes, and (aq) marks an aqueous one. Molarity is moles of solute per litre of solution, \(c = n/V\), in mol/L or M. Rearranged, \(n = cV\) and \(V = n/c\); multiply moles by molar mass to get grams. Make solutions in a volumetric flask, filled to the mark. Dilution adds solvent but keeps the moles of solute fixed, so \(c_1V_1 = c_2V_2\), with \(V_2\) the final total volume.
Flashcards
Flashcard
A homogeneous mixture of two or more substances
Test your understanding
Question 1 of 5
What is the molarity of a solution made by dissolving 0.250 mol of sodium hydroxide, NaOH, to make 500.0 mL of solution?
Question 2 of 5
What mass of potassium nitrate, KNO₃ (101.11 g/mol), is needed to make 0.250 L of a 0.400 M solution?
Question 3 of 5
50.0 mL of 2.00 M sodium chloride solution is diluted with water to a final volume of 250.0 mL. What is the new concentration?
Question 4 of 5
What volume of 12.0 M hydrochloric acid stock is needed to make 2.00 L of 0.600 M hydrochloric acid?
Question 5 of 5
Why is a 1.00 M solution made by filling a volumetric flask to its 1.00 L mark, not by adding 1.00 mol of solute to 1.00 L of water?
