Electrical Engineering › Section J · Series, parallel, and series-parallel ac circuits › Topic J.5
Equivalent circuits and phase measurement
Any impedance can be pictured as a resistance and a reactance in series, or as a different pair in parallel, and at one frequency the two pictures are indistinguishable from outside. This topic shows how to switch between them, how to measure phase angles on an oscilloscope, and where these ideas meet real hardware.
Two circuits, one impedance
Two networks are equivalent at a given frequency if they present the same impedance at their terminals: a source connected to either one delivers the same current at the same phase. Any passive impedance \(Z = R + jX\) can be built as a resistance in series with a reactance, but it can equally be built as a resistance in parallel with a reactance of a different size. Switching between the two forms is useful in practice. A real inductor, for example, has winding resistance in series with its inductance, yet many calculations go faster if that coil is treated as a parallel branch alongside other parallel loads.
Series to parallel
Start with a series pair \(R_s + jX_s\). Its admittance, from the topic "Admittance and parallel ac networks", is
A parallel pair with resistance \(R_p\) and reactance \(X_p\) has admittance \(1/R_p - j/X_p\). Matching the real and imaginary parts gives
The reactance keeps its type: an inductive series reactance becomes an inductive parallel one, and a capacitive one stays capacitive. Both parallel values are always larger than the series values they replace.
Worked example: series to parallel
Find the parallel equivalent of an 8 Ω resistance in series with an inductive reactance of 6 Ω. 1. Sum of squares: \(R_s^2 + X_s^2 = 64 + 36 = 100\). 2. Parallel resistance: \(R_p = 100/8 = 12.5\,\Omega\). 3. Parallel reactance: \(X_p = 100/6 = 16.7\,\Omega\), inductive. 4. Check by computing both impedances: the series pair is \(8 + j6 = 10\angle 36.87^\circ\,\Omega\), and the parallel pair is
The two match, so a source cannot tell them apart at this frequency.
Parallel to series
Going the other way, take the product over the sum of the parallel pair and separate its real and imaginary parts. The result is
Again the reactance keeps its type, and now both series values are smaller than the parallel ones. If you remember just one pair of formulas, you can always recover the other by working with admittance: invert the parallel admittance \(1/R_p - j/X_p\) and read off the real and imaginary parts of the impedance.
Worked example: parallel to series
A 2 kΩ resistor is in parallel with a capacitive reactance of 1 kΩ. Find the series equivalent. 1. Sum of squares, in kΩ²: \(R_p^2 + X_p^2 = 4 + 1 = 5\). 2. Series resistance: \(R_s = (2)(1)^2/5 = 0.400\) kΩ. 3. Series reactance: \(X_s = (2)^2(1)/5 = 0.800\) kΩ, capacitive. So the network equals 400 Ω in series with 800 Ω of capacitive reactance, \(400 - j800\,\Omega = 894\angle -63.4^\circ\,\Omega\). 4. Check:
which agrees.
Equivalent at one frequency only
The equivalence holds only at the frequency used to calculate it, because reactances change with frequency in different ways from the formulas. Double the frequency in the first example and the series pair becomes \(8 + j12 = 14.4\angle 56.3^\circ\,\Omega\). The parallel pair, whose reactance also doubles to 33.3 Ω, becomes \(11.7\angle 20.6^\circ\,\Omega\): a quite different impedance. An equivalent circuit is therefore a snapshot. When a problem involves several frequencies, convert again at each one, or keep the original circuit.
Worked example: reading a phase shift
A dual-trace oscilloscope shows two sinusoids at once, so their phase difference can be read off the screen. One full period spans 360°, so
Suppose channel 1 shows a 400 Hz source voltage e and channel 2 the inductor voltage of a series R-L circuit, with the time base at 0.25 ms per division. 1. Period: \(T = 1/400 = 2.5\) ms, which is 10 divisions. 2. The inductor trace peaks 1.5 divisions before the source trace. 3. Phase: \(\theta = (1.5/10) \times 360^\circ = 54^\circ\), with \(v_L\) leading e. 4. Check: an inductor voltage should lead the source in a series R-L circuit, by less than 90°.
Grounds and sensing resistors
Both channels of a typical bench oscilloscope share one ground, normally tied to the circuit's ground, so every trace is a voltage measured from that common point. Connecting a probe ground anywhere else can short out part of the circuit. If the scope ground were clipped between the resistor and the inductor of a grounded series R-L circuit, it would short whichever element lay between that point and circuit ground, changing the current and possibly damaging parts. To see a current's phase, insert a small sensing resistor with one end at ground: its voltage is in phase with its current. It must be small compared with the other impedances, so it barely disturbs the circuit.
Applications: a real coil and home wiring
A 50 mH coil with 30 Ω of winding resistance, at 1 kHz, has \(X_L = 314\,\Omega\). Its parallel model is \(R_p = 3.32\) kΩ across \(X_p = 317\,\Omega\), so in a parallel network it acts almost like a pure inductance with a large resistance beside it. Homes rely on parallel connection too. A US home is usually fed at 120/240 V, 60 Hz: lights and outlets connect in parallel across 120 V, so each receives full voltage and works independently, while large loads such as ranges use 240 V. Switches sit in series with what they control, and metal cases are bonded to ground. Panels are for qualified electricians: never open one live.
Common mistakes to avoid
1. Copying the series values into the parallel circuit: 8 Ω and 6 Ω in series are not 8 Ω and 6 Ω in parallel. 2. Swapping the formulas: \(R_p\) divides the sum of squares by \(R_s\), and \(X_p\) divides it by \(X_s\). 3. Changing the type of reactance during a conversion. 4. Using an equivalent at a frequency other than the one it was calculated for. 5. Reading the phase shift in divisions without dividing by the divisions in one period. 6. Clipping an oscilloscope ground to a point other than circuit ground.
Key takeaways
At one frequency, any impedance can be modelled as a series pair or a parallel pair. Series to parallel: \(R_p = (R_s^2 + X_s^2)/R_s\) and \(X_p = (R_s^2 + X_s^2)/X_s\). Parallel to series: \(R_s = R_pX_p^2/(R_p^2 + X_p^2)\) and \(X_s = R_p^2X_p/(R_p^2 + X_p^2)\). The reactance keeps its type, and the equivalence fails at other frequencies. On a dual-trace oscilloscope, phase is the shift divided by the period, times 360°. Keep one common ground, and use a small grounded sensing resistor to see current phase.
Flashcards
Flashcard
Networks with the same terminal impedance at a given frequency
Test your understanding
Question 1 of 5
What is the parallel equivalent of a 3 Ω resistance in series with an inductive reactance of 4 Ω?
Question 2 of 5
A 10 Ω resistor is in parallel with an inductive reactance of 10 Ω. What is the series equivalent?
Question 3 of 5
On a dual-trace oscilloscope one period spans 6 divisions, and one trace is shifted 1 division from the other. What is the phase difference?
Question 4 of 5
In a grounded series R-L circuit, why must the oscilloscope ground not be clipped to the junction between R and L?
Question 5 of 5
An 8 + j6 Ω series pair is replaced by its parallel equivalent, 12.5 Ω with j16.7 Ω, found at 60 Hz. What happens at 120 Hz?
