Electrical Engineering › Section J · Series, parallel, and series-parallel ac circuits › Topic J.4
Frequency response of the parallel R-L network
Put an inductor in parallel with a resistor and sweep the frequency: at the bottom of the range the inductor shorts everything out, and at the top it all but disappears. Tracing that change shows how parallel networks respond to frequency, and it rounds off the study of parallel ac circuits.
A network that changes with frequency
The topic "Frequency response of the R-C circuit" followed a series circuit as the source frequency changed. This topic does the same for a resistor R in parallel with an inductor L, both connected between the same two nodes. Because inductive reactance \(X_L = 2\pi fL\) rises with frequency while R stays fixed, the network's impedance, its angle and the way current divides between the branches all change across the frequency range. The analysis uses the parallel tools from "Admittance and parallel ac networks": admittances add, and the product-over-sum rule handles two branches.
The two extremes
Begin with the limits, which tell you what to expect. At very low frequency \(X_L\) is tiny, so the inductor is close to a short circuit placed straight across the resistor. Almost all the current flows through the inductor, and the network's impedance approaches zero. At very high frequency \(X_L\) is huge, so the inductor is close to an open circuit and the network behaves like R alone. In a parallel network the branch with the smaller impedance dominates, so the network is mainly inductive below the frequency at which \(X_L = R\) and mainly resistive above it. That is the reverse of the series R-L circuit.
The impedance formula
For two branches in parallel,
The angle follows from dividing \(RX_L\angle 90^\circ\) by \(R + jX_L\), whose angle is \(\tan^{-1}(X_L/R)\); the difference \(90^\circ - \tan^{-1}(X_L/R)\) equals \(\tan^{-1}(R/X_L)\). The admittance view is quicker to read: \(Y_T = G - jB_L\), and since \(B_L = 1/(2\pi fL)\) shrinks as f rises, \(Y_T\) shrinks towards G. So \(|Z_T|\) rises from zero towards R, never above it, and the angle falls from 90° towards 0°.
The crossover frequency
The branches have equal impedance magnitudes where \(X_L = R\), at
This is the same expression as for the series R-L circuit, but the network's behaviour on either side is reversed. At \(f_1\),
so the magnitude is \(0.707R\) and the angle exactly 45°. Compare a series R-L circuit at its crossover, whose impedance is \(\sqrt{2}R\) at 45°: the same angle, but a magnitude twice as large.
Worked example: sweeping a current-driven network
A 2 mA current source drives a 2.2 kΩ resistor in parallel with a 100 mH inductor. Find the impedance and voltage across the range. 1. Crossover: \(f_1 = 2200/(2\pi \times 0.1) = 3.50\) kHz. 2. At each frequency find \(X_L\), then \(Z_T\), then \(V = IZ_T\). 3. Results, with \(|Z_T|\) in kΩ and V in volts:
4. Check: at \(f_1\), \(|Z_T| = 2.2/\sqrt{2} = 1.56\) kΩ, and V approaches \(IR = 4.4\) V at high frequency.
Branch currents against frequency
With a current source, the total current is fixed and the question is how it splits. The resistor current \(I_R = V/R\) is in phase with the voltage and grows with frequency, from almost nothing towards the full source current. The inductor current \(I_L = V/X_L\) lags the voltage by 90° and shrinks. In the sweep above, the inductor carries 2.00 mA of the 2 mA at 100 Hz but only 0.232 mA at 30 kHz. At \(f_1\) the two branches carry equal currents of \(2/\sqrt{2} = 1.41\) mA, and at every frequency \(I_R^2 + I_L^2 = I^2\), because the branch currents are 90° apart.
Worked example: a voltage-driven network
Now drive the same 2.2 kΩ and 100 mH pair from a 10 V source and compare 1 kHz with 10 kHz. 1. The resistor current is fixed: \(I_R = 10/2200 = 4.55\) mA at any frequency. 2. At 1 kHz, \(X_L = 628\,\Omega\), so \(I_L = 15.9\) mA at −90°, and \(\mathbf{I}_s = 4.55 - j15.9 = 16.6\angle -74.1^\circ\) mA. The power factor is \(\cos 74.1^\circ = 0.275\) lagging. 3. At 10 kHz, \(X_L = 6.28\) kΩ, so \(I_L = 1.59\) mA and \(\mathbf{I}_s = 4.82\angle -19.3^\circ\) mA, with \(F_p = 0.944\) lagging. 4. Check: the current angles match the impedance angles in the sweep table with the sign reversed, as \(\mathbf{I}_s = \mathbf{E}/Z_T\) requires.
The parallel R-C network by analogy
Replace the inductor with a capacitor and the response turns over. Capacitive reactance falls as frequency rises, so a parallel R-C network looks like R at low frequency, where the capacitor is nearly open, and like a short at high frequency, where it nearly shorts the resistor. Its impedance magnitude falls from R towards zero, and its angle moves from 0° towards −90°. The crossover where \(X_C = R\) is at \(f_1 = 1/(2\pi RC)\), and there \(Z_T = 0.707R\angle -45^\circ\). This is why a capacitor placed across a signal line shunts high-frequency noise to ground.
Summary: parallel ac networks
Every element of a parallel network has the same voltage across it. The total admittance is the sum of the branch admittances, and the total impedance is its reciprocal. Kirchhoff's current law holds for phasors, so the source current is the phasor sum of the branch currents. The resistor current is in phase with the voltage, the inductor current lags it by 90° and the capacitor current leads it by 90°. The branch with the smaller impedance takes the larger current and sets the character of the network. And the power factor \(G_T/|Y_T|\) is closer to 1 the more the conductance dominates the net susceptance.
Common mistakes to avoid
1. Carrying over series intuition: a parallel R-L network is resistive at high frequency, not inductive. 2. Expecting \(|Z_T|\) to exceed R: in parallel it rises towards R from below. 3. Writing \(\sqrt{2}R\) at the crossover, which is the series result; the parallel value is \(R/\sqrt{2}\). 4. Getting the angle wrong: the parallel R-L angle is \(\tan^{-1}(R/X_L)\), not \(\tan^{-1}(X_L/R)\). 5. Adding branch current magnitudes, instead of using \(I_R^2 + I_L^2 = I^2\). 6. Forgetting which kind of source drives the network: a current source fixes the total current, a voltage source fixes the resistor current.
Key takeaways
In a parallel R-L network the inductor shorts the resistor at low frequency and nearly vanishes at high frequency. The impedance rises from zero towards R and its angle falls from 90° towards 0°. At the crossover \(f_1 = R/(2\pi L)\), \(X_L = R\) and \(Z_T = 0.707R\angle 45^\circ\). With a current source the network voltage rises towards IR as frequency increases; with a voltage source the source current falls and the power factor rises. A parallel R-C network mirrors this, falling from R towards zero with \(f_1 = 1/(2\pi RC)\).
Flashcards
Flashcard
The inductor nearly shorts the resistor; Z_T is close to zero
Test your understanding
Question 1 of 5
A 1.0 kΩ resistor is in parallel with a 22 mH inductor. At what frequency are the two branch impedances equal in magnitude?
Question 2 of 5
A parallel R-L network has R = 1.0 kΩ. What is its impedance at the frequency where X_L = R?
Question 3 of 5
A constant-current source drives a parallel R-L network at a frequency far below its crossover. What is the voltage across the network like?
Question 4 of 5
A 12 V source feeds a 1.0 kΩ resistor in parallel with an inductor whose reactance is 500 Ω. What is the power factor?
Question 5 of 5
How does the impedance of a parallel R-C network change as the frequency rises from near zero?
