Electrical Engineering › Section O · Pulses, nonsinusoidal signals, and system analysis › Topic O.4

Input and output impedance, gains, and cascaded systems

Many circuits arrive as sealed modules: an amplifier board, an audio chip, a sensor interface. You cannot see inside, but four numbers describe how each one behaves at its terminals, and they predict what happens when modules are connected to a source, a load and each other.

Systems as black boxes

A packaged amplifier is used only through its terminals, so engineers describe it by its terminal behaviour rather than its parts. The common model is the two-port: an input port, terminals 1 and 1′, where the signal enters, and an output port, terminals 2 and 2′, where it leaves; often 1′ and 2′ are a shared ground. Four quantities describe a simple amplifier: its input impedance \(Z_i\), output impedance \(Z_o\), no-load voltage gain \(A_{v_{NL}}\), and the phase of that gain. This topic assumes linear systems and, as is typical for amplifiers in their mid-band, purely resistive impedances, written \(R_i\) and \(R_o\).

Input impedance

The input impedance is the ratio of the voltage across the input terminals to the current that flows into them:

Z_i = \frac{E_i}{I_i}

An ohmmeter cannot measure it, because the system must be powered and driven at its working frequency, and an ohmmeter uses its own dc source on de-energised circuits. Instead, put a small sensing resistor \(R_s\) in series between a signal generator \(E_g\) and the input. Measure \(E_g\) and \(E_i\) with a meter rated for the frequency; then \(I_i = (E_g - E_i)/R_s\) and \(Z_i = E_i/I_i\). Choose \(R_s\) small enough not to disturb the system, but large enough to give a measurable voltage difference.

Output impedance

The output impedance is what the load sees looking back into the output terminals with the input signal set to zero: \(Z_o = E_o/I_o\) when a test voltage drives the output. A simpler method uses two gain measurements. Measure the gain with no load, \(A_{v_{NL}}\), then with a known load \(R_L\), \(A_v\). Because the output behaves like a source with internal resistance \(R_o\),

R_o = R_L\Big(\frac{A_{v_{NL}}}{A_v} - 1\Big)

For example, if the no-load gain is 80 and falls to 64 with a 1 kΩ load, then \(R_o = 1000(80/64 - 1) = 250\,\Omega\). It is the idea of Internal resistance and voltage regulation, applied to an ac output.

The amplifier model and three voltage gains

The model is a resistance \(R_i\) across the input, and at the output a voltage-controlled voltage source \(A_{v_{NL}}E_i\) in series with \(R_o\). Three gains follow. The no-load gain \(A_{v_{NL}} = E_o/E_i\) with nothing connected, the figure on a data sheet. Adding a load \(R_L\) forms a divider with \(R_o\), so the loaded gain is

A_v = A_{v_{NL}}\,\frac{R_L}{R_L + R_o}

always less than \(A_{v_{NL}}\). A source with internal resistance \(R_g\) forms another divider with \(R_i\), so the total gain from the source voltage is

A_{v_T} = \frac{E_o}{E_g} = A_v\,\frac{R_i}{R_i + R_g}

always less than \(A_v\).

Worked example: a loaded amplifier

An amplifier module has \(A_{v_{NL}}\) = 150, \(R_i\) = 10 kΩ and \(R_o\) = 1.2 kΩ. It is driven by a 20 mV rms source with \(R_g\) = 2.0 kΩ and feeds a 4.7 kΩ load. Find \(A_v\), \(A_{v_T}\) and the output voltage. 1. Output divider: \(A_v = 150 \times \frac{4.7}{4.7 + 1.2} = 119.5\). 2. Input divider: \(A_{v_T} = 119.5 \times \frac{10}{10 + 2.0} = 99.6\). 3. Output: \(E_o = 99.6 \times 20\,\text{mV} = 1.99\,\text{V}\) rms. 4. Check: the source loses about 17% across \(R_g\) and the output loses about 20% across \(R_o\), so the total gain is roughly two thirds of 150, as found. The data-sheet gain of 150 would have overestimated the output by half.

Current gain and power gain

With the output current \(I_o\) taken as flowing out of the system into the load, the input current is \(I_i = E_i/R_i\) and the load current is \(I_o = E_o/R_L\), so the loaded current gain is

A_i = \frac{I_o}{I_i} = A_v\,\frac{R_i}{R_L}

The power gain compares the power delivered to the load with the power taken in at the input: \(A_G = P_o/P_i = A_v A_i\), or \(A_v^2 R_i/R_L\). In decibels it uses the power form, \(10\log_{10} A_G\). Two-port texts often define \(I_o\) as flowing into the output terminal instead, which puts a minus sign in \(A_i\); the magnitudes are the same.

Worked example: the gain trade-off

Continue with the amplifier above (\(R_i\) = 10 kΩ, \(R_o\) = 1.2 kΩ, \(A_{v_{NL}}\) = 150). 1. With \(R_L\) = 4.7 kΩ: \(A_i = 119.5 \times \frac{10}{4.7} = 254\), and \(A_G = 119.5 \times 254 = 30{,}400\), or 44.8 dB. 2. Double the load to 9.4 kΩ: \(A_v = 150 \times \frac{9.4}{10.6} = 133\), a rise of 11%. 3. But \(A_i = 133 \times \frac{10}{9.4} = 142\), a fall of 44%. 4. So \(A_G = 133 \times 142 = 18{,}800\), or 42.7 dB. Check: a larger load resistance raises the voltage gain towards \(A_{v_{NL}}\) but draws less current, so the power delivered drops. Designers balance voltage gain, current gain and output power for each application.

Cascaded systems

When stages are connected in a chain, each stage's load is the input impedance of the next, and the last stage drives the real load. The overall gain is the product of the loaded gains,

A_{v_T} = A_{v_1} A_{v_2} A_{v_3} \cdots

never the product of the no-load gains. In decibels the loaded gains add, as in Logarithms and decibels. The overall current gain follows from the overall voltage gain, the first stage's input resistance and the final load, \(A_{i_T} = A_{v_T} R_{i_1}/R_L\). Two habits help: give the first stage a high input impedance, so it barely loads the source, and give the last stage a low output impedance, so it holds its gain into the load.

Worked example: two stages in cascade

Stage 1 has \(A_{v_{NL}}\) = 40, \(R_i\) = 50 kΩ and \(R_o\) = 2 kΩ. Stage 2 has \(A_{v_{NL}}\) = 25, \(R_i\) = 8 kΩ and \(R_o\) = 100 Ω, and drives a 1 kΩ load. An ideal 5 mV source drives stage 1. 1. Stage 1 is loaded by stage 2's 8 kΩ: \(A_{v_1} = 40 \times \frac{8}{8 + 2} = 32\). 2. Stage 2 is loaded by 1 kΩ: \(A_{v_2} = 25 \times \frac{1000}{1100} = 22.7\). 3. Overall: \(A_{v_T} = 32 \times 22.7 = 727\), or \(30.1 + 27.1 = 57.2\) dB. 4. Output: \(727 \times 5\,\text{mV} = 3.64\,\text{V}\). 5. Check: the nameplate product, \(40 \times 25 = 1000\), would overstate the gain by 38%, mostly because stage 1's 2 kΩ output drives an 8 kΩ input.

Common mistakes to avoid

First, multiplying nameplate no-load gains for a cascade: each stage must be loaded by the next. Second, forgetting the source resistance: \(A_{v_T}\) includes the divider formed by \(R_g\) and \(R_i\). Third, measuring \(Z_i\) or \(Z_o\) with an ohmmeter: these are ac quantities of a powered system. Fourth, finding \(Z_o\) with the input signal still applied: the input must be set to zero. Fifth, using 20 log for power gain: \(A_G\) is a power ratio, so it takes 10 log.

Key takeaways

A packaged system is modelled as a two-port with input impedance Z_i = E_i/I_i and output impedance Z_o, the latter found with the input set to zero or from R_o = R_L(A_vNL/A_v − 1). The model is R_i at the input and A_vNL·E_i in series with R_o at the output. Loaded gain A_v = A_vNL·R_L/(R_L + R_o); total gain from the source A_vT = A_v·R_i/(R_i + R_g). Current gain A_i = A_v·R_i/R_L and power gain A_G = A_v·A_i. Larger loads raise A_v but lower A_i. Cascaded gains multiply only as loaded gains, or add in dB.

Flashcards

Flashcard

Two-port

A system described only by the voltages and currents at an input port and an output port

Terminals 1-1′ and 2-2′.

Test your understanding

Question 1 of 5

An amplifier has a no-load gain of 60 and an output resistance of 500 Ω. What is its voltage gain into a 2 kΩ load?

Question 2 of 5

An amplifier with R_i = 5 kΩ and loaded gain A_v = 40 is driven by a source with R_g = 1 kΩ. What is the total gain A_vT from the source voltage?

Question 3 of 5

Two stages have no-load gains of 20 and 30. Stage 1 has R_o = 1 kΩ and stage 2 has R_i = 4 kΩ; stage 2 drives a load equal to its own R_o. What is the overall voltage gain?

Question 4 of 5

An amplifier's gain is 50 with no load and 40 with a 3 kΩ load. What is its output resistance?

Question 5 of 5

An amplifier with R_i = 20 kΩ has a loaded voltage gain of 25 into a 500 Ω load. What is its power gain?

← Previous topicNext topic →