Electrical Engineering › Section A · Introduction, current, and voltage › Topic A.2

Atoms, current, and voltage

Every circuit runs on two ideas: current, the rate at which charge moves, and voltage, the energy each unit of charge gains or loses. Both start inside the atom, with electrons that some materials hold tightly and others let wander.

Inside the atom

In the simple Bohr picture, an atom has a small nucleus of positive protons and neutral neutrons, surrounded by negative electrons in shells. Each electron carries a charge of \(-1.602 \times 10^{-19}\) C and each proton \(+1.602 \times 10^{-19}\) C, so a neutral atom has equal numbers of each. A proton is about 1,836 times as massive as an electron, which is why electrons, not protons, do the moving in a wire. Shell \(n\) can hold at most \(2n^2\) electrons: 2, 8, 18 and 32 for the first four shells. Modern quantum theory refines this picture, but the shell idea explains conduction well enough for circuit work.

Why copper conducts

Copper has 29 electrons, arranged 2, 8, 18 and then a single electron in the fourth shell. That lone outer, or valence, electron is far from the nucleus and shielded by the 28 below it, so it is only weakly bound. In solid copper these valence electrons are not tied to any one atom: they form a sea of free electrons that drift through the lattice of copper ions: about \(8.5 \times 10^{28}\) of them per cubic metre. Silver and gold have the same single-valence-electron structure, which is why they are also excellent conductors. Materials whose outer electrons are tightly bound have very few free charges and behave as insulators.

Charge and Coulomb's law

Charge \(Q\) is measured in coulombs (C). One coulomb is the charge of about \(6.242 \times 10^{18}\) electrons, the reciprocal of the elementary charge. Like charges repel and opposite charges attract, with a force given by Coulomb's law:

F = \frac{kQ_1Q_2}{r^2}, \quad k \approx 8.99 \times 10^{9}\,\text{N m}^2/\text{C}^2

The force falls with the square of the distance \(r\): double the separation and the force drops to a quarter. Two charges of 1 µC each, 10 cm apart, push on each other with about 0.899 N. Charge is conserved: it moves from place to place but is never created or destroyed. The topic "The electric field" develops these forces further.

Current: the rate of charge flow

Connect a battery across a copper wire and the free electrons, which were moving randomly, acquire a net drift in one direction. Current is the rate at which charge passes a point:

I = \frac{Q}{t}

in amperes (A), where 1 A is 1 coulomb per second. For a changing current the instantaneous form is \(i = \frac{dq}{dt}\). Surprisingly, the electrons drift slowly: 1 A in a copper wire of 1 mm² cross-section corresponds to a drift speed of only about 0.07 mm/s. A lamp still lights almost at once, because the push travels along the wire at a large fraction of the speed of light, moving all the free electrons together.

Conventional current and electron flow

By convention, current direction is the direction positive charge would move: out of a source's positive terminal, through the external circuit and back into its negative terminal. In metal wires the moving charges are electrons, which travel the opposite way. Both descriptions predict the same circuit behaviour. Some books, including Kuphaldt's Lessons in Electric Circuits, draw electron flow; this course uses conventional current throughout. It also uses the passive sign convention: for a load, current enters the terminal marked + and leaves the terminal marked −. Direct current (dc) flows in one direction only; alternating current (ac) reverses direction periodically.

Worked example: current from counted charge

A meter detects \(3.00 \times 10^{19}\) electrons passing a point in a wire in 2.00 s. Find the current. 1. Convert electrons to coulombs: \(Q = (3.00 \times 10^{19})(1.602 \times 10^{-19}\,\text{C}) = 4.81\) C. 2. Divide by time: \(I = \frac{Q}{t} = \frac{4.81\,\text{C}}{2.00\,\text{s}} = 2.40\) A. 3. Check the size: 1 A is about \(6.24 \times 10^{18}\) electrons per second, and here \(1.50 \times 10^{19}\) pass each second, which is 2.40 times as many. The conventional current points opposite to the direction the electrons travel.

Voltage: energy per charge

Moving charge from one point to another can require energy or release it. Voltage, or potential difference, is the energy per unit charge:

V = \frac{W}{Q}

in volts (V), where 1 V is 1 joule per coulomb; the instantaneous form is \(v = \frac{dw}{dq}\). A 9 V battery gives each coulomb that passes through it 9 J of energy, and that energy is delivered to the circuit as the charge flows through the loads. A water analogy helps: voltage is like pressure in a pipe and current like the flow rate, and with no pressure difference nothing flows. Voltage sources are often labelled \(E\) and the voltage across a load \(V\).

Voltage is always between two points

A voltage is never a property of a single point. It compares two: \(V_{ab} = V_a - V_b\) is the potential of point \(a\) measured relative to point \(b\), and \(V_{ba} = -V_{ab}\). For convenience one point in a circuit is chosen as the reference, called ground or node 0, and given 0 V. A single-subscript voltage such as \(V_a\) then means the voltage of point \(a\) relative to ground. If \(V_a = 9\) V and \(V_b = 3\) V, then \(V_{ab} = 6\) V: point \(a\) is 6 V higher. The older term electromotive force (emf) is still used for the voltage a source produces.

Worked example: charge and energy from a charger

A charger delivers a steady 1.50 A to a 3.7 V battery pack for 40.0 minutes. 1. Time in seconds: \(t = 40.0 \times 60 = 2400\) s. 2. Charge delivered: \(Q = It = 1.50 \times 2400 = 3600\) C. 3. Number of electrons: \(3600 \times 6.242 \times 10^{18} = 2.25 \times 10^{22}\). 4. Energy, from \(W = VQ\): \(3.7 \times 3600 = 13{,}320\) J, about \(1.33 \times 10^{4}\) J. 5. Check the units: amperes times seconds give coulombs, and volts times coulombs give joules, because a volt is a joule per coulomb. The voltage is treated as constant here; a real pack's voltage changes a little as it charges.

Common mistakes to avoid

First, leaving time in minutes or hours in \(I = \frac{Q}{t}\): the ampere is a coulomb per second. Second, inverting the formulas, as in \(V = \frac{Q}{W}\); check that the units come out right. Third, describing a voltage "at" a point without saying what it is measured against. Fourth, mixing conventional current with electron flow in the same diagram: pick conventional current and keep it. Fifth, thinking electrons race round a circuit at the speed of light; the signal travels fast, but the drift is slow. Sixth, forgetting that the electron charge is negative when its sign matters.

Key takeaways

Atoms have a nucleus of protons and neutrons with electrons in shells holding up to 2n² electrons. Copper's single, weakly bound valence electron gives it a sea of free electrons. Charge is measured in coulombs; one electron carries 1.602 × 10⁻¹⁹ C, and 1 C is about 6.242 × 10¹⁸ electrons. Coulomb's law gives the force between charges, falling with the square of distance. Current I = Q/t in amperes; conventional current flows from + to − through the external circuit. Voltage V = W/Q in volts, always measured between two points, often relative to ground.

Flashcards

Flashcard

Electron charge

−1.602 × 10⁻¹⁹ C

A proton carries the same amount, positive.

Test your understanding

Question 1 of 5

A charge of 18 C passes a point in a wire in 1.0 minute. What is the current?

Question 2 of 5

Moving 0.50 C of charge between two points takes 6.0 J of energy. What is the voltage between the points?

Question 3 of 5

A lamp is connected across a battery. In this course's convention, which way does the current flow?

Question 4 of 5

Point a is at 9 V and point b is at 3 V, both measured from ground. What is V_ba?

Question 5 of 5

Why does solid copper have so many free electrons?

← Previous topicNext topic →