Electrical Engineering › Section A · Introduction, current, and voltage › Topic A.3

DC supplies, conductors, and insulators

A circuit needs something to push charge and something to carry it. This topic surveys the common dc sources, from batteries to bench supplies, and explains why some materials carry current freely while others block it almost completely.

What a dc supply does

A dc voltage source keeps a fixed polarity between its terminals, so current through the external circuit always flows the same way. Ideally it holds its voltage constant whatever current the circuit draws. In a circuit diagram a battery is drawn as a pair of parallel lines, the longer one the positive terminal and the shorter one the negative, and a source is often labelled \(E\). There are three broad families: batteries, which convert chemical energy; generators, which convert mechanical energy; and power supplies, which convert the ac from a wall outlet into dc. Solar cells, which convert light, form a fourth.

Cells, batteries and chemistries

A cell is the basic chemical unit: two electrodes in an electrolyte. A battery, strictly, is several cells connected together, though the word is used for single cells too. Primary cells cannot be recharged; secondary cells can, because their chemical reaction reverses when current is driven back through them. Typical nominal voltages per cell:

\begin{array}{ll} \text{alkaline (primary)} & 1.5\,\text{V} \\ \text{lithium coin (primary)} & 3\,\text{V} \\ \text{lead-acid} & 2.0\,\text{V} \\ \text{nickel-metal hydride} & 1.2\,\text{V} \\ \text{lithium-ion} & 3.6\text{-}3.7\,\text{V} \end{array}

A car's "12 V" lead-acid battery is six cells giving about 12.6 V, or 2.1 V per cell, when fully charged. Lithium-ion cells, charged to about 4.2 V, power phones, laptops and electric vehicles.

Ampere-hour ratings

A battery's capacity is the total charge it can deliver, quoted in ampere-hours (Ah), or mAh for small cells. Since 1 Ah is 1 A for 3600 s, it equals 3600 C. The ideal running time is

\text{life (h)} = \frac{\text{capacity (Ah)}}{\text{current drawn (A)}}

so a 100 Ah battery could supply 1 A for 100 h or 10 A for 10 h. Real batteries fall short of this at high currents: the faster they are discharged, the less of their charge they deliver, which is why data sheets quote capacity at a stated discharge rate. Capacity also drops in the cold, as anyone whose car will not start on a winter morning knows.

Worked example: running time

A 2.4 Ah nickel-metal hydride pack powers a small instrument. 1. At a steady 150 mA, the ideal life is \(\frac{2.4\,\text{Ah}}{0.150\,\text{A}} = 16\) h. 2. The pack is moved to a motor drawing 800 mA. Dividing the rated capacity gives \(\frac{2.4}{0.800} = 3.0\) h. 3. The data sheet shows that at 800 mA the usable capacity is only 1.9 Ah, so the realistic life is \(\frac{1.9}{0.800} = 2.38\) h, about 2 h 23 min. 4. Check: the current rose by a factor of about 5.3 while the life fell by a factor of about 6.7, because the usable capacity also shrank at the higher drain.

Generators, power supplies and solar cells

A dc generator produces voltage when its shaft is turned. Laboratory and electronic equipment mostly use power supplies that rectify and filter the ac mains, 120 V at 60 Hz in the US or 230 V at 50 Hz in much of the world, into a steady dc output; the circuits inside are covered in "Power supply circuits". A silicon solar cell produces about 0.5 to 0.6 V, so modules connect dozens in series. Bright sunlight delivers roughly 1000 W per square metre, of which modern commercial modules convert around a fifth. A dc current source, the dual of a voltage source, ideally holds its current fixed; "Current sources and source conversions" treats it fully.

The bench power supply

A typical bench supply has an adjustable, regulated output and three terminals: positive (often red), negative (often black) and ground (often green), bonded to mains earth through the power cord. Joining the negative terminal to ground puts the positive terminal above ground. Joining the positive terminal to ground instead gives a negative output: set to 15 V, the black terminal sits at \(-15\) V. With neither terminal grounded the output is floating: the set voltage still appears between the terminals, but neither has a defined voltage relative to ground.

Worked example: a split supply

A circuit needs +10 V and \(-15\) V, both relative to a common ground, from two bench supplies, A and B. 1. Set supply A to 10 V and join its negative terminal to ground; its positive terminal is then at \(V = +10\) V. 2. Set supply B to 15 V and join its positive terminal to ground; its negative terminal is then at \(V = -15\) V. 3. The voltage between the two live terminals is \(V_{ab} = V_a - V_b = 10 - (-15) = 25\) V, where \(a\) is A's positive terminal and \(b\) is B's negative terminal. 4. Check: a meter across those two terminals, red lead on \(a\), should read +25 V.

Conductors

A conductor lets charge flow easily, because it has many free electrons. Metals with a single loosely bound valence electron are the best. Conductivity is often stated as a percentage of annealed copper's:

\begin{array}{ll} \text{tungsten} & \approx 31\% \\ \text{aluminium} & \approx 61\% \\ \text{gold} & \approx 70\% \\ \text{copper} & 100\% \\ \text{silver} & \approx 108\% \end{array}

Silver is best but expensive, so copper is used for most wiring. Gold plates connector contacts because it does not corrode. Aluminium, though it conducts less well, is so much lighter that it is preferred for overhead transmission lines.

Insulators

An insulator has very few free electrons, so it carries almost no current under normal conditions. Rubber, PVC and other plastics, glass, porcelain, mica and dry air are common examples, used to coat wires and support power lines. Every insulator has a breakdown strength, the electric stress at which it suddenly conducts: dry air breaks down at roughly 3 kV per millimetre, which is why sparks jump small gaps at high voltage, while good solid insulators withstand tens of kilovolts per millimetre or more. Between conductors and insulators lie the semiconductors, the subject of the next topic.

Worked example: energy stored in a battery

A phone battery is rated 3.7 V and 4000 mAh. How much energy does it hold? 1. Capacity in coulombs: \(4.000\,\text{Ah} \times 3600\,\text{C/Ah} = 14{,}400\) C. 2. Energy from \(W = VQ\): \(3.7 \times 14{,}400 = 53{,}280\) J, about \(5.33 \times 10^{4}\) J. 3. The same energy in watt-hours is simply volts times ampere-hours: \(3.7 \times 4.000 = 14.8\) Wh. 4. Check: \(14.8\,\text{Wh} \times 3600\,\text{s/h} = 53{,}280\) J, which agrees. Airline battery limits are stated in watt-hours because it measures stored energy directly.

Common mistakes to avoid

First, treating an ampere-hour rating as energy: it is charge, and you need the voltage too to find energy. Second, assuming a battery delivers its rated capacity at any current; capacity falls at high drain and low temperature. Third, putting a primary cell in a charger designed for secondary cells. Fourth, thinking a floating supply has no voltage: the voltage between its terminals is there, but neither terminal is referenced to ground. Fifth, confusing the green ground terminal with the negative terminal of a bench supply. Sixth, assuming any insulator blocks any voltage; above its breakdown strength it conducts.

Key takeaways

DC sources keep a fixed polarity: batteries, generators, rectifying power supplies and solar cells. Primary cells are single-use; secondary cells recharge. Nominal cell voltages are about 1.5 V alkaline, 2.0 V lead-acid (2.1 V charged), 1.2 V NiMH and 3.6 to 3.7 V lithium-ion. Life in hours is capacity in Ah divided by current, an upper limit at high drain. Energy is volts times ampere-hours, in watt-hours. A bench supply's output can be positive, negative or floating relative to ground. Silver, copper, gold and aluminium conduct well; insulators conduct almost nothing until they break down.

Flashcards

Flashcard

DC source

Keeps a fixed polarity between its terminals

Current in the circuit flows one way only.

Test your understanding

Question 1 of 5

A battery rated 1.2 Ah supplies a steady 300 mA. Ideally, how long will it last?

Question 2 of 5

A bench supply is set to 12 V with its positive terminal joined to ground. What is the voltage of its negative terminal relative to ground?

Question 3 of 5

Which statement about a 12.6 V, 60 Ah car battery is correct?

Question 4 of 5

Why is aluminium, rather than copper, usually chosen for overhead transmission lines?

Question 5 of 5

Which of these cells is a primary cell?

← Previous topicNext topic →