Electrical Engineering › Section I · Sinusoidal waveforms and phasors › Topic I.3

Average and rms values

A changing waveform still has to be summed up by single numbers: how much dc it carries, and how hard it can heat a resistor. The average value answers the first question and the rms value the second, and the rms value is the one printed on every ac nameplate.

Two numbers for a changing wave

The instantaneous value of an ac voltage changes all the time, so a single figure on a nameplate must mean something more specific. Two summaries matter. The average value is the steady, dc part of the waveform, which a dc meter responds to. The effective or rms value measures the power the waveform delivers to a resistor, which a heater, a lamp or a fuse responds to. The two can be very different: a pure sinusoid has an average of zero but certainly heats things.

The average value

The average value of a periodic waveform is its net area over one period divided by the period:

V_{av} = \frac{\text{area over one cycle}}{T}

Areas above the axis count as positive and areas below as negative, so they can cancel. For simple shapes made of rectangles and triangles you can add the areas directly; for curves you integrate. A sinusoid has equal areas above and below the axis, so its average over a full cycle is exactly zero. A dc meter connected to a pure sinusoid therefore reads zero, however large the wave.

Average of half a sine wave

Over one positive half cycle the area under \(V_m \sin\alpha\) is \(2V_m\), so the half-cycle average is

V_{av} = \frac{1}{\pi}\int_0^{\pi} V_m \sin\alpha \, d\alpha = \frac{2V_m}{\pi}

That is about \(0.637V_m\). The result matters for rectifiers. A full-wave rectified sine, where every negative half is flipped upward, repeats that half cycle, so its average is \(0.637V_m\). A half-wave rectified sine, with the negative halves removed and replaced by zero, has the same area spread over twice the time, giving \(V_m/\pi \approx 0.318V_m\).

A dc level plus an ac wave

Many signals are a sinusoid riding on a dc level: \(v(t) = V_0 + V_m \sin(\omega t + \theta)\). The sinusoidal part averages to zero, so the average of the whole signal is simply \(V_0\). On an oscilloscope set to dc coupling, \(V_0\) appears as the height of the wave's centre line above the ground trace. The output of a transistor amplifier, which carries an ac signal on a dc bias, is a common example. Shifting a waveform up or down changes its average by exactly the size of the shift and leaves its shape and peak-to-peak value unchanged.

Worked example: a pulse train

A waveform sits at +12 V for 3 ms, then at −4 V for 1 ms, and repeats. Find its average value. 1. Period: \(T = 3 + 1 = 4\,\text{ms}\). 2. Areas: the positive part gives \(12 \times 3 = 36\,\text{V}\cdot\text{ms}\) and the negative part \(-4 \times 1 = -4\,\text{V}\cdot\text{ms}\). 3. Net area: \(32\,\text{V}\cdot\text{ms}\). 4. Average: \(V_{av} = 32/4 = 8\,\text{V}\). 5. Check: the wave spends three quarters of its time at +12 V, so the average should lie closer to 12 than to −4, and 8 V does. A dc voltmeter on this signal would read 8 V.

The effective, or rms, value

The effective value of an ac voltage is the dc voltage that would deliver the same average power to the same resistor. Because power in a resistor is \(v^2/R\), matching the average power means matching the average of \(v^2\). So you square the waveform, find the mean over one period, and take the square root:

V_{rms} = \sqrt{\frac{1}{T}\int_0^{T} v^2 \, dt}

The name records the steps backwards: root of the mean of the square. Squaring makes every part of the wave count positively, which is why a sinusoid with zero average still has a large rms value. The same definition applies to currents.

The rms value of a sinusoid

For \(v = V_m \sin\alpha\), the identity \(\sin^2\alpha = (1 - \cos 2\alpha)/2\) shows that \(\sin^2\) averages to one half over a cycle, because the cosine term averages to zero. So the mean of \(v^2\) is \(V_m^2/2\) and

V_{rms} = \frac{V_m}{\sqrt{2}} \approx 0.707V_m

Conversely \(V_m = \sqrt{2}\,V_{rms}\). A US outlet's 120 V is an rms value: its peak is about 170 V and its peak-to-peak value about 339 V. A 230 V supply peaks near 325 V. In this course an ac magnitude written as a capital letter, such as V or I, is rms unless it is labelled peak.

Worked example: the pulse train's rms

Find the rms value of the same pulse train: +12 V for 3 ms, then −4 V for 1 ms. 1. Square each level: \(12^2 = 144\,\text{V}^2\) and \((-4)^2 = 16\,\text{V}^2\). 2. Area of the squared wave: \(144 \times 3 + 16 \times 1 = 448\,\text{V}^2\cdot\text{ms}\). 3. Mean: \(448/4 = 112\,\text{V}^2\). 4. Root: \(V_{rms} = \sqrt{112} = 10.6\,\text{V}\), to three significant figures. 5. Check: the rms value, 10.6 V, is larger than the 8 V average, because the negative part now adds to the heating instead of cancelling. Across a 10 Ω resistor this wave would deliver \(112/10 = 11.2\,\text{W}\).

Worked example: a heater on 120 V

A 24 Ω heating element is connected to 120 V, 60 Hz mains. 1. The 120 V is rms, so the average power is \(P = V^2/R = 120^2/24 = 600\,\text{W}\). 2. The rms current is \(I = 120/24 = 5\,\text{A}\). 3. The peak current is \(\sqrt{2} \times 5 = 7.07\,\text{A}\). 4. The instantaneous power swings between 0 and \((\sqrt{2} \times 120)^2/24 = 1200\,\text{W}\), twice per cycle; its average is half the peak, 600 W, matching step 1. 5. Check: a 120 V dc supply would give the same 600 W, which is exactly what "effective value" promises.

Other shapes, and dc plus ac

Each waveform shape has its own ratio of rms to peak. A square wave alternating between \(+V_m\) and \(-V_m\) has \(v^2 = V_m^2\) all the time, so its rms value equals \(V_m\). A symmetrical triangle wave has \(V_{rms} = V_m/\sqrt{3} \approx 0.577V_m\). For a dc level plus a sinusoid, the cross terms average to zero and the powers simply add:

V_{rms} = \sqrt{V_0^2 + V_{ac}^2}

where \(V_{ac}\) is the rms value of the sinusoidal part. For \(v = 5 + 10\sin\omega t\,\text{V}\), that gives \(\sqrt{25 + 50} = 8.66\,\text{V}\), while the average is 5 V.

Common mistakes to avoid

First, using \(0.707V_m\) for a waveform that is not a sinusoid; the factor belongs to sine waves only. Second, treating mains 120 V as a peak value, which understates the true peak by 50 V. Third, adding rms values of a dc part and an ac part directly instead of combining their squares. Fourth, forgetting that areas below the axis are negative when finding an average. Fifth, quoting \(0.637V_m\) as the full-cycle average of a sinusoid; it is the half-cycle or rectified average, and the full-cycle average is zero.

Key takeaways

The average value is net area over one period divided by T; a sinusoid averages to zero over a full cycle, and to 2V_m/π ≈ 0.637V_m over a half cycle. Full-wave rectified sines average 0.637V_m and half-wave ones 0.318V_m. A dc level V_0 under any zero-average wave is the average. The rms value is the root of the mean of the square, the dc value giving the same heating. For a sinusoid V_rms = V_m/√2 ≈ 0.707V_m, so 120 V mains peaks at about 170 V. Square waves have V_rms = V_m, triangles V_m/√3, and dc plus ac combines as √(V_0² + V_ac²).

Flashcards

Flashcard

Average value

Net area over one period divided by the period

Areas below the axis count as negative.

Test your understanding

Question 1 of 5

A sinusoidal voltage has a peak value of 18 V. What is its rms value?

Question 2 of 5

A waveform is +10 V for 2 ms and −6 V for 2 ms, repeating. What is its average value?

Question 3 of 5

What is the rms value of v = 6 + 8√2 sin(ωt) V?

Question 4 of 5

What is the average value of a full-wave rectified sine with a peak of 50 V?

Question 5 of 5

A 48 Ω resistor is connected to 120 V rms mains. What average power does it absorb?

← Previous topicNext topic →