Electrical Engineering › Section I · Sinusoidal waveforms and phasors › Topic I.2

Phase relations

In an ac circuit the voltage across an element and the current through it usually rise and fall at the same rate but not in step. The phase relation between them, which one leads and by how much, decides how the element behaves and how much power it takes.

Same frequency, different timing

Watch the voltage across a motor and the current into it on a dual-trace oscilloscope and you see two sinusoids of exactly the same frequency, but their peaks do not line up. One reaches each peak a fixed time before the other, every cycle. That fixed offset is the phase relation. In the general format from "Sinusoidal waveforms and their general format", \(v(t) = V_m \sin(\omega t + \theta)\), the timing of each wave is carried entirely by its phase angle \(\theta\), so comparing two waves comes down to comparing their phase angles.

Leading and lagging

Take two sinusoids of the same frequency, \(v = V_m \sin(\omega t + \theta_v)\) and \(i = I_m \sin(\omega t + \theta_i)\). The phase difference is \(\theta_v - \theta_i\). If it is positive, the voltage reaches every peak, and every zero crossing, earlier than the current: the voltage leads the current, and the current lags the voltage. If it is negative, the roles swap. The two statements are one fact told from each side: "v leads i by 40°" and "i lags v by 40°" mean the same thing. The peak values play no part; a tiny current can lead a huge voltage.

Rules for a fair comparison

A phase comparison only means something when three conditions hold. First, the two waves must have the same frequency; otherwise their timing drifts every cycle and no fixed lead exists. Second, both must be written in the same form, as sines with positive peak values. Third, the difference should be quoted between −180° and +180°. A lead of 270° is the same timing as a lag of 90°, because adding or subtracting 360° changes nothing, and engineers always quote the smaller description. Phase angles are written in radians inside a sine whose \(\omega\) is a number, but leads and lags are usually stated in degrees.

Converting to the sine form

Waves often arrive as cosines or with minus signs, so you need a few identities. A cosine is a sine that started a quarter cycle earlier:

\cos x = \sin\left(x + \frac{\pi}{2}\right)

A minus sign is a half-cycle shift, which you may take either way: \(-\sin x = \sin(x \pm \pi)\). Combining the two gives \(-\cos x = \sin(x - \pi/2)\). Choose the sign of the \(\pm\pi\) shift that keeps the final phase angle between \(-\pi\) and \(\pi\). After converting, every wave has a positive peak value and a sine, and the phase angles can be compared directly.

In phase, out of phase, and quadrature

Three phase differences have names. Two waves are in phase when the difference is zero: they peak and cross zero together, as the voltage and current of a resistor do. They are out of phase, or in antiphase, when the difference is 180°: one peaks positive just as the other peaks negative, so their sum is the difference of their peaks. They are in quadrature when the difference is 90°: one is at zero when the other is at a peak. The topic "Response of R, L, and C to sinusoids" shows that an inductor's voltage leads its current by 90° and a capacitor's current leads its voltage by 90°.

Phase difference as a time shift

A phase difference \(\Delta\theta\) in radians corresponds to a time offset \(\Delta t = \Delta\theta / \omega\). With degrees it is often easier to use a fraction of the period:

\Delta t = \frac{\Delta\theta}{360^\circ}\,T

At 60 Hz, where \(T = 16.7\,\text{ms}\), a 120° phase difference is one third of a cycle, 5.56 ms. The same 120° at 1 kHz is only 0.333 ms. Phase is therefore the more useful description: the time offset between two waves depends on the frequency, but 120° always means one third of a cycle.

Worked example: which one leads?

A voltage \(v = 12 \sin(377t + \pi/4)\,\text{V}\) is applied across a load carrying \(i = 3 \sin(377t - \pi/12)\,\text{A}\). 1. Both are sines with positive peaks at the same \(\omega\), so they can be compared. 2. Phase difference: \(\theta_v - \theta_i = \pi/4 + \pi/12 = \pi/3\) rad, which is 60°. 3. It is positive, so the voltage leads the current by 60°; the current lags by 60°. 4. Time offset: \(\Delta t = (\pi/3)/377 = 2.78\,\text{ms}\). 5. Check: 2.78 ms is one sixth of the 16.7 ms period, and 60° is one sixth of 360°.

Worked example: a cosine and a minus sign

Compare \(v = 8 \cos(1000t - \pi/6)\,\text{V}\) with \(i = -2 \sin(1000t + \pi/6)\,\text{A}\). 1. Convert the cosine by adding \(\pi/2\): \(v = 8 \sin(1000t + \pi/3)\). 2. Remove the minus sign by subtracting \(\pi\), which keeps the angle inside \(\pm\pi\): \(i = 2 \sin(1000t - 5\pi/6)\). 3. Difference: \(\pi/3 - (-5\pi/6) = 7\pi/6\) rad, which is 210°. 4. Reduce to the range ±180°: \(210^\circ - 360^\circ = -150^\circ\). 5. Conclusion: the current leads the voltage by 150°, a time offset of \((5\pi/6)/1000 = 2.62\,\text{ms}\).

Worked example: phase on an oscilloscope

Two signals of equal frequency are shown on a dual-trace oscilloscope at 0.1 ms per division. One full cycle spans 8 divisions. Channel 2 crosses zero going positive 1.2 divisions after channel 1 does. 1. Period: \(T = 8 \times 0.1\,\text{ms} = 0.8\,\text{ms}\), so \(f = 1.25\,\text{kHz}\). 2. Time offset: \(\Delta t = 1.2 \times 0.1\,\text{ms} = 0.12\,\text{ms}\). 3. Phase: \(\Delta\theta = 360^\circ \times 1.2/8 = 54^\circ\). 4. Channel 2 is later, so it lags channel 1 by 54°. Measuring between matching zero crossings is more precise than between rounded peaks.

Common mistakes to avoid

First, comparing waves of different frequencies, which have no fixed phase relation. Second, comparing a cosine with a sine, or a wave with a negative peak, before converting both to positive sines. Third, getting the direction backwards: the wave with the larger phase angle leads, and a larger angle means earlier, not later. Fourth, quoting a lead of 270° instead of a lag of 90°. Fifth, letting the peak values influence the answer; only the phase angles decide which wave leads.

Key takeaways

For two sinusoids of the same frequency written as positive sines, the phase difference is θ_v − θ_i; the wave with the larger angle leads and the other lags by the same amount. Convert first with cos x = sin(x + π/2) and −sin x = sin(x ± π). Quote differences between −180° and +180°. Zero is in phase, 180° is out of phase, 90° is quadrature. A phase difference Δθ is a time offset Δt = Δθ/ω, or (Δθ/360°) × T. On an oscilloscope, measure the offset between matching zero crossings as a fraction of the period.

Flashcards

Flashcard

Phase difference

θ_v − θ_i for two same-frequency sinusoids

Compare only waves of equal frequency.

Test your understanding

Question 1 of 5

Given v = 10 sin(ωt + π/3) V and i = 2 sin(ωt − π/6) A, what is the phase relation?

Question 2 of 5

Written as a sine with a positive peak and a phase angle between −π and π, what is i = −4 sin(ωt + π/4)?

Question 3 of 5

At 60 Hz, what time offset corresponds to a phase difference of 90°?

Question 4 of 5

A calculation gives a voltage leading its current by 270°. How should this be quoted?

Question 5 of 5

On a dual-trace oscilloscope one cycle spans 10 divisions, and channel B crosses zero rising 2 divisions before channel A. Which statement is correct?

← Previous topicNext topic →