Electrical Engineering › Section P · Semiconductor theory, diodes, and transistors › Topic P.11

Feedback, amplifier impedances, current mirrors, ratings, and quirks

Real transistors are unpredictable: β wanders, currents drift with heat, and gain fades at high frequency. Negative feedback, careful impedance work, current mirrors and respect for ratings are how engineers build dependable circuits from them anyway.

Feeding the output back

Feedback sends a portion of the output signal back to mix with the input. Feedback that reinforces a change is called positive, or regenerative: a microphone held near its own loudspeaker howls because each pass round the loop grows louder. Controlled, it makes oscillators, as in "Differentiators, integrators, and positive feedback". Negative, or degenerative, feedback opposes any change. It lowers the gain, but the gain becomes steadier, distortion falls, bandwidth widens and the circuit depends far less on β and temperature. A common-emitter stage gets it from an unbypassed emitter resistor or a resistor from collector to base; a bypass capacitor keeps the feedback for dc only.

Worked example: emitter degeneration

A common-emitter stage has \(R_C = 3.3\,\text{k}\Omega\) and runs at \(I_E = 2.0\,\text{mA}\); then warming and a new transistor shift it to 1.0 mA. 1. Without feedback, \(R_E\) bypassed: \(r_e = 13\,\Omega\), so \(A_v = -3300/13 = -254\). 2. At 1.0 mA, \(r_e = 26\,\Omega\) and \(A_v = -127\): the gain has halved. 3. With 330 Ω unbypassed: \(A_v = -3300/343 = -9.62\) at 2.0 mA. 4. At 1.0 mA: \(A_v = -3300/356 = -9.27\), a change of under 4%. 5. Check: the feedback version gives up most of its gain, but its gain is now set mainly by the ratio \(R_C/R_E = 10\), two resistors, rather than by the transistor.

Feedback around high gain

Wrap negative feedback round an amplifier of open-loop gain \(A\), returning a fraction \(B\) (op-amp topics write β) of the output to subtract from the input. The closed-loop gain becomes

A_f = \frac{A}{1 + AB}

When \(AB\) is large, \(A_f\) approaches \(1/B\), which depends only on the resistors that set \(B\). With \(A = 10{,}000\) and \(B = 0.01\), \(A_f = 99.0\); halve \(A\) to 5000 and \(A_f\) is still 98.0, a change of 1%. Three direct-coupled common-emitter stages invert an odd number of times, so one resistor from output to input gives negative feedback. Op-amps carry the idea furthest, as "Negative feedback and divided feedback" shows.

Amplifier impedances

Input resistance decides how much a stage loads its source, as in "Input and output impedance, gains, and cascaded systems". From the base, emitter resistance looks \(\beta + 1\) times larger, \((\beta + 1)(r_e + R_E)\), with the bias divider \(R_{TH}\) in parallel. That is a few kilohms for a common-emitter stage with \(R_E\) bypassed, and high for an emitter follower, whose load is in the emitter. A common-base input is near \(r_e\), tens of ohms. Output resistance is about \(R_C\) for common-emitter and common-base stages, and low for the follower: \(r_e\) plus the source-side resistance over \(\beta + 1\).

Current mirrors

A current mirror copies one current into another. Transistor Q1 has its collector tied to its own base, so it acts as a diode, and a resistor \(R\) from the supply feeds it a reference current \(I_{ref} = (V_{CC} - V_{BE})/R\). Q2 shares Q1's base-emitter voltage. A matched transistor at the same temperature with the same \(V_{BE}\) carries the same current, so Q2's collector current mirrors \(I_{ref}\),

I_{out} = I_{ref}\,\frac{\beta}{\beta + 2}

whatever the load, while Q2 stays active. An NPN mirror sinks current; a PNP mirror sources it. On a chip, mirrors replace load resistors, and a transistor of twice the area carries twice the current.

Worked example: a current mirror

An NPN mirror on 15 V uses \(R = 6.8\,\text{k}\Omega\) and matched transistors with β = 100. Find the output current and the largest load it can drive. 1. Reference: \(I_{ref} = (15 - 0.7)/6800\) A = 2.10 mA. 2. Output: \(2.10 \times 100/102 = 2.06\,\text{mA}\). 3. Compliance: Q2 must keep about 0.3 V across it to stay active, so the load may drop at most 14.7 V. 4. Largest load: \(14.7/2.06\,\text{mA} = 7.13\,\text{k}\Omega\). 5. Check: any load from 0 to about 7 kΩ receives 2.06 mA, like a current source. In practice a slight rise of current with \(V_{CE}\) and any temperature difference spoil the copy, so discrete pairs are mounted in thermal contact.

Transistor ratings and packages

Every BJT has limits. Power dissipation \(P_D = V_{CE} I_C\) is rated at 25 °C and derated above it. Reverse-voltage ratings cover collector-emitter, collector-base and emitter-base; the emitter-base junction breaks down at only about 5 to 7 V in small-signal parts. Maximum collector current, saturation voltages and β are also listed. The common 2N3904 in TO-92 has maximum ratings \(V_{CEO}\) = 40 V, \(I_C\) = 200 mA and \(P_D\) = 625 mW derated at 5 mW/°C, with \(h_{FE}\) from 100 to 300 at 10 mA. Power packages such as the TO-220 handle tens of watts only on a heatsink, a watt or two in free air, and their metal tab is often the collector.

Worked example: derating

A 2N3904 drops 6.0 V while carrying 50 mA, inside an enclosure at 60 °C. Is it within rating? 1. Dissipation: \(P = 6.0 \times 0.050 = 0.300\,\text{W}\). 2. Allowed at 60 °C: \(625 - 5 \times (60 - 25) = 450\,\text{mW}\). 3. Margin: 300 mW is two thirds of the limit, acceptable. 4. Hottest safe ambient for this load: \(25 + (625 - 300)/5 = 90\) °C. 5. Check the other limits: 50 mA is under 200 mA and 6.0 V under 40 V. Saturated at 50 mA it would dissipate only about 10 mW; heat comes from the active region, where voltage and current coexist.

Quirks: distortion, drift and runaway

A BJT is nonlinear: collector current rises exponentially with \(V_{BE}\), and β changes with current, so large swings distort. Small signals and negative feedback reduce this. \(V_{BE}\) falls about 2 mV per °C and β rises with temperature, both raising the current; a differential pair, whose two \(V_{BE}\) drops track and cancel, is the usual cure in direct-coupled circuits. In thermal runaway, current heats the transistor, heat raises the current, and the cycle can destroy it; emitter resistance breaks the loop. Paralleled transistors do not share equally, because the hottest hogs the current; emitter ballast resistors, often well under an ohm, and a shared heatsink force sharing.

High frequency and noise

Junction capacitances make the gain fall at high frequency, the collector-base one magnified by the Miller effect of "Common-emitter, common-collector, common-base, and cascode amplifiers". The transition frequency \(f_T\) is where the small-signal current gain \(h_{fe}\) falls to 1; above the β roll-off, \(|h_{fe}| \approx f_T/f\), so a 300 MHz part offers a current gain of about 10 at 30 MHz. Noise sets the smallest usable signal. A resistance \(R\) at temperature \(T\) produces thermal noise

v_n = \sqrt{4kTR\,\Delta f}

in bandwidth \(\Delta f\), with k Boltzmann's constant: 1.82 µV rms for 10 kΩ at 300 K over 20 kHz. Transistors add shot noise and low-frequency 1/f noise. The noise figure, \(F = (S/N)_{in}/(S/N)_{out}\), is quoted as \(10\log_{10} F\) dB.

Common mistakes to avoid

First, judging feedback negative because the gain fell; the test is whether it opposes a change. Second, ignoring the bias divider when finding input resistance. Third, forgetting that emitter resistance looks \(\beta + 1\) times larger from the base. Fourth, using the 25 °C power rating in a hot enclosure. Fifth, assuming a current mirror drives any load; it needs compliance. Sixth, paralleling BJTs without ballast resistors.

Key takeaways

Positive feedback makes oscillators; negative feedback trades gain for stability, low distortion and bandwidth, and with high loop gain \(A_f \approx 1/B\). Emitter degeneration makes the common-emitter gain about \(R_C/R_E\). From the base, emitter resistance looks \(\beta + 1\) times larger, in parallel with the bias divider. A current mirror copies \(I_{ref} = (V_{CC} - V_{BE})/R\) into a load within its compliance. Respect \(P_D = V_{CE} I_C\) with derating, the voltage and current limits, and the spread of β. Distortion, temperature drift, thermal runaway, current hogging, junction capacitance and noise are the BJT's practical limits.

Flashcards

Flashcard

Positive feedback

Feedback that reinforces a change; used to build oscillators

Microphone howl is the uncontrolled kind.

Test your understanding

Question 1 of 5

An amplifier with open-loop gain 2000 has negative feedback with a fraction B = 0.02 returned to the input. What is its closed-loop gain?

Question 2 of 5

An NPN current mirror on 9.0 V uses a 3.9 kΩ reference resistor and high-β matched transistors. About what current does it copy into its load?

Question 3 of 5

A transistor is rated 625 mW at 25 °C, derated at 5.0 mW per °C. What is its power limit at an ambient temperature of 85 °C?

Question 4 of 5

A common-emitter stage has a bias divider with R_TH = 10 kΩ, β = 150, r_e = 25 Ω and an unbypassed 470 Ω emitter resistor. What is its input resistance?

Question 5 of 5

A transistor has a transition frequency f_T of 300 MHz. About what small-signal current gain does it offer at 30 MHz, above its β roll-off?

← Previous topicNext topic →