Electrical Engineering › Section P · Semiconductor theory, diodes, and transistors › Topic P.12

Junction field-effect transistors: switching and active mode

A field-effect transistor controls current with a voltage instead of a current, so its control input draws almost nothing. The junction FET, the simplest kind, is normally on, turns off when its gate is reverse biased, and can act as a switch, a current regulator or a voltage-controlled resistor.

Control by voltage

A BJT needs a steady base current. A field-effect transistor (FET) instead uses an electric field, set by the gate-source voltage, to widen or narrow a conducting path called the channel. Almost no current enters the gate, so the control supplies almost no power. FETs are also unipolar: the channel current is carried by one kind of carrier, electrons in an N-type channel or holes in a P-type one, and it never crosses a PN junction. This topic covers the junction FET (JFET); "Insulated-gate FETs (MOSFETs) and IGBTs" covers the other family.

Structure and symbol

A JFET is a bar of doped silicon, the channel, with a source lead at one end and a drain lead at the other. A region of the opposite type, the gate, is diffused into the side of the bar, forming a PN junction with the channel. In the schematic symbol the gate line carries an arrow pointing from P to N: into the channel for an N-channel JFET, out of it for P-channel. N-channel parts are more common. In use the gate-channel junction is reverse biased, so the gate current is only leakage, typically nanoamps or less. Because the channel is one piece, many JFETs work with source and drain swapped, though some are built asymmetrically.

Normally on, pinched off

With the gate shorted to the source, \(V_{GS} = 0\), the channel is wide open: a JFET is a normally-on device, the opposite of a BJT. The current it then regulates, given enough drain-source voltage, is \(I_{DSS}\), its maximum. Make an N-channel gate negative relative to the source and the reverse-biased junction's depletion region spreads into the channel and squeezes it, like a hand on a hose. At the pinch-off voltage \(V_P\), also written \(V_{GS(off)}\), the channel closes and the drain current falls to nearly zero. \(V_P\) is a few volts, negative for N-channel parts, and varies widely between units. Never forward-bias the gate by more than a few tenths of a volt.

The JFET as a switch

Put the drain and source where the contacts of a switch would be, with a load and supply in series. With \(V_{GS} = 0\) the JFET conducts and the load is on. To switch it off, apply a gate voltage beyond pinch-off, negative with respect to the source for an N-channel part, which usually needs a negative supply. The control delivers almost no current, an advantage over a BJT. One catch: the gate-channel junction has a small capacitance, which once charged can hold the JFET off after the control is disconnected. A gate-to-source bleed resistor, often hundreds of kilohms to a megohm, discharges it quickly. JFETs make good analogue signal switches.

Meter checks

The gate-channel junction tests like a diode on the diode-check range. For an N-channel JFET, red on the gate and black on the source or the drain reads about 0.6 to 0.7 V, and the reverse reads OL; a P-channel part is the mirror image. The drain-source path is a plain resistance, the same in both directions, typically tens to a few hundred ohms with no gate voltage. Charge on the gate capacitance, even from handling, can pinch the channel and give a misleading high reading, so first short gate to source or push the leads into conductive anti-static foam. A reverse gate voltage should then raise the drain-source reading.

Three regions and a naming trap

Drain characteristic curves plot \(I_D\) against \(V_{DS}\) for several values of \(V_{GS}\). For small \(V_{DS}\) the current rises in proportion: this is the ohmic, or triode, region, where the channel acts as a resistance set by \(V_{GS}\). Once \(V_{DS} \ge V_{GS} - V_P\) the current levels off and is regulated by \(V_{GS}\) alone; this is the region used for amplifying. FET texts call it the saturation, or pinch-off, region, which means current regulation, the equivalent of the BJT's active region, not the BJT's fully-on saturation. With \(V_{GS}\) beyond \(V_P\) the JFET is cut off, and at very high \(V_{DS}\) it breaks down and the current surges.

The square-law transfer curve

In the saturation region the drain current follows Shockley's equation:

I_D = I_{DSS}\left(1 - \frac{V_{GS}}{V_P}\right)^2

valid for \(V_{GS}\) between \(V_P\) and 0. The square makes the JFET nonlinear: equal steps in \(V_{GS}\) give unequal steps in current, so large signals distort, while a BJT's collector current is nearly proportional to its base current. Because the input is a voltage and the output a current, a JFET has no β. Its gain figure is the transconductance, \(g_m = \Delta I_D/\Delta V_{GS}\), in siemens. Differentiating Shockley's equation gives

g_m = \frac{2I_{DSS}}{|V_P|}\left(1 - \frac{V_{GS}}{V_P}\right)

largest at \(V_{GS} = 0\) and falling to zero at pinch-off.

Worked example: a transfer curve

A typical small-signal N-channel JFET has \(I_{DSS} = 8.0\,\text{mA}\) and \(V_P = -4.0\,\text{V}\). Find \(I_D\) and \(g_m\) in the saturation region. 1. At \(V_{GS} = -1\,\text{V}\): \(I_D = 8.0(1 - 0.25)^2 = 4.50\,\text{mA}\). 2. At −2 V: \(8.0(0.5)^2 = 2.00\,\text{mA}\). 3. At −3 V: \(8.0(0.25)^2 = 0.50\,\text{mA}\). 4. Each 1 V step removes 3.5, then 2.5, then 1.5 mA: the curve is not straight. 5. Transconductance at −2 V: \(g_m = (16/4.0)(0.5) = 2.0\,\text{mS}\), half of the 4.0 mS at \(V_{GS} = 0\). 6. Check the boundary: at −1 V the JFET is in saturation only for \(V_{DS} \ge -1 - (-4) = 3\,\text{V}\).

The JFET as a current regulator

Tie the gate to the source and the JFET passes \(I_{DSS}\) over a wide range of drain-source voltage, so it becomes a two-terminal constant-current device; packaged this way it is sold as a current-regulator diode. A resistor \(R_S\) in the source lead sets a smaller current, because the drain current through \(R_S\) makes \(V_{GS} = -I_D R_S\), a self-bias. For the JFET above with \(R_S = 470\,\Omega\), solving \(I_D = 8.0(1 - 0.47 I_D/4.0)^2\), with \(I_D\) in milliamperes, gives \(I_D = 3.16\,\text{mA}\) and \(V_{GS} = -1.49\,\text{V}\). The equation's other root, 22.9 mA, is rejected because it would put \(V_{GS}\) beyond pinch-off.

Worked example: a voltage-controlled resistor

For small \(V_{DS}\) in the ohmic region, Shockley's model gives a channel resistance

r_{DS} = \frac{|V_P|}{2I_{DSS}(1 - V_{GS}/V_P)}

Use the same JFET, \(I_{DSS} = 8.0\,\text{mA}\) and \(V_P = -4.0\,\text{V}\). 1. At \(V_{GS} = 0\): \(r_{DS} = 4.0/0.016 = 250\,\Omega\). 2. At −2 V: \(250/0.5 = 500\,\Omega\). 3. At −3 V: \(250/0.25 = 1.00\,\text{k}\Omega\). 4. As a signal switch in series with a 10 kΩ load, the on state passes \(10/10.25 = 97.6\%\) of a small signal, and beyond pinch-off almost nothing. 5. Check: more negative \(V_{GS}\) narrows the channel and raises the resistance, as it should. Keep \(V_{DS}\) to a few tenths of a volt, or the resistance stops being constant.

Common mistakes to avoid

First, treating a JFET like a BJT: it is normally on and needs reverse gate voltage to turn off. Second, forward-biasing the gate junction. Third, reading "saturation" as fully on; for FETs it is the current-regulating region. Fourth, assuming drain current is proportional to \(V_{GS}\); the law is square. Fifth, forgetting that \(V_P\) and \(V_{GS}\) are both negative for N-channel parts, so \(V_{GS}/V_P\) is positive. Sixth, testing the channel while charge is stored on the gate.

Key takeaways

FETs are voltage-controlled and unipolar, with almost no gate current. A JFET's reverse-biased gate junction squeezes its channel: normally on at \(I_{DSS}\), off beyond the pinch-off voltage \(V_P\). As a switch it needs a beyond-pinch-off gate voltage and a gate bleed resistor. The gate tests as one diode; the channel as a resistance either way. Regions are ohmic, saturation (current-regulating, for \(V_{DS} \ge V_{GS} - V_P\)) and cutoff. In saturation \(I_D = I_{DSS}(1 - V_{GS}/V_P)^2\) and the gain figure is \(g_m\) in siemens. In the ohmic region it is a voltage-controlled resistor; with gate tied to source, a current regulator.

Flashcards

Flashcard

FET

Field-effect transistor: gate voltage controls channel current

Almost no gate current.

Test your understanding

Question 1 of 5

An N-channel JFET has I_DSS = 12 mA and V_P = −3.0 V. In the saturation region, what drain current flows at V_GS = −1.5 V?

Question 2 of 5

For the same JFET (I_DSS = 12 mA, V_P = −3.0 V), what is the transconductance at V_GS = −1.5 V?

Question 3 of 5

An N-channel JFET with V_P = −4 V has V_GS = −1 V and V_DS = 2 V. Which region is it in?

Question 4 of 5

How is an N-channel JFET switch turned off so that it also turns back on reliably?

Question 5 of 5

A JFET with I_DSS = 10 mA and V_P = −5.0 V is used as a voltage-controlled resistor at small V_DS. What is its channel resistance at V_GS = −2.0 V?

← Previous topicNext topic →