Electrical Engineering › Section P · Semiconductor theory, diodes, and transistors › Topic P.8

The BJT as a switch, meter checks, and active-mode operation

A bipolar junction transistor lets a small current steer a much larger one. Used fully on or fully off it is a switch; held in between it is the heart of an amplifier, and both uses rest on the same three terminals and three operating regions.

One current controls another

The first transistor was demonstrated at Bell Labs in late 1947, and transistors soon replaced fragile, power-hungry vacuum tubes. A bipolar junction transistor (BJT) is a three-layer sandwich of doped silicon, N-P-N or P-N-P, with a lead on each layer: emitter, base and collector. A small current into the base controls a much larger current through the collector. Why the thin middle layer does this is the subject of "Inside BJTs, JFETs, MOSFETs, and thyristors"; here the BJT is a component, judged at its terminals.

Terminals, arrows and current directions

The schematic symbol marks the emitter with an arrow, and the arrow shows the direction of conventional current. In an NPN transistor the arrow points out: current flows into the base and into the collector, and both leave together through the emitter. In a PNP every direction and polarity is reversed. The arrow follows the course's current-direction convention, set out in "Atoms, current, and voltage". Kirchhoff's current law ties the three currents together:

I_E = I_B + I_C

The base current is small, so the emitter and collector currents are nearly equal.

Two junctions, two jobs

Inside the BJT are two PN junctions. For the transistor to control current, the base-emitter junction must be forward biased, which for silicon takes about 0.7 V, base positive for NPN. The collector-base junction is normally reverse biased, so on its own it would block. Base current overrides that block: each unit of base current lets a limited multiple of it cross into the collector. Emitter and collector are both N-type in an NPN but not interchangeable; the emitter is far more heavily doped, and a transistor wired backwards controls current poorly.

Three operating regions

A BJT works in one of three regions. In cutoff, the base-emitter junction is not forward biased, the base current is zero and the collector passes almost nothing: an open switch. In the active region, the base-emitter junction is forward biased and the collector-base junction is reverse biased, so the collector current is set by the base current. In saturation, both junctions are forward biased; the transistor passes as much current as the supply and load allow, and the collector-emitter voltage falls to \(V_{CE(sat)}\), typically 0.1 to 0.3 V for a small-signal part. Switches use cutoff and saturation; amplifiers stay in the active region.

The transistor as a switch

To switch a load, connect it between the positive supply and the collector of an NPN transistor, with the emitter grounded; this is a low-side switch. A resistor \(R_B\) from the control signal to the base limits the base current. With the control at 0 V the transistor is cut off. With the control high, enough base current flows to saturate it and the load sees nearly the whole supply. The control source carries only the base current, so a logic pin or sensor can command a heavy load, whose power still comes from the supply.

Worked example: a relay from a 3.3 V pin

A microcontroller pin at 3.3 V must operate a 12 V relay with a 240 Ω coil. The transistor's data sheet guarantees \(\beta \ge 100\) at this current. 1. Saturated load current: \(I_C = (12 - 0.2)/240 = 49.2\,\text{mA}\), far more than a pin should supply. 2. Minimum base current: \(49.2/100 = 0.492\,\text{mA}\). 3. Overdrive about five times to guarantee saturation: about 2.46 mA. 4. Base resistor: \(R_B = (3.3 - 0.7)/2.46\,\text{mA}\) = 1.06 kΩ; the E12 value 1.0 kΩ gives 2.60 mA, within a typical pin rating. 5. Check: the transistor dissipates only \(0.2 \times 49.2 = 9.8\,\text{mW}\). The coil is inductive, so it needs a flyback diode across it, as "Inductor commutating and diode switching circuits, and Zener diodes" explains.

Meter checks: two back-to-back diodes

On a multimeter's diode-check range, whose red lead is positive, a good BJT looks like two diodes sharing the base. For an NPN, red on the base and black on the emitter or collector reads about 0.6 to 0.7 V; reversed, both read OL, as does collector to emitter either way. A PNP gives the mirror image. The base-emitter reading is usually slightly higher, because the collector-base junction is larger and more lightly doped. Two conducting readings out of six is healthy; any other count means a fault or a different device. The method is in "Diode basics, meter checks, ratings, and rectifier circuits".

Worked example: naming the leads

An unmarked transistor has pins X, Y and Z. On diode check, red on Y and black on X reads 0.684 V; red on Y and black on Z reads 0.671 V; the other four combinations read OL. 1. Y appears in both conducting readings, so Y is the base. 2. The positive red lead was on the base, so the base is P-type: an NPN. 3. The higher reading, 0.684 V, marks the base-emitter junction, so X is the emitter. 4. So Z is the collector. 5. Check: exactly two of six readings conduct. Lead order varies between packages, so test or read the data sheet.

Active mode: a current regulator

Hold the base current fixed and sweep the collector-emitter voltage. Above a few tenths of a volt the collector current barely changes: the transistor regulates it at a multiple of the base current. One such curve per base current forms the characteristic curves. The multiple is the current gain:

\beta = \frac{I_C}{I_B}

Data sheets call the dc value \(h_{FE}\). For small-signal parts it is typically 50 to 300, varying between units and with current and temperature, so good designs never rely on an exact value. The best simple model is a base-emitter diode driving a current source of \(\beta I_B\) that draws its energy from the supply; a diode plus a variable resistor is poorer, because it predicts current rising with voltage.

Worked example: active or saturated?

An NPN with \(\beta = 150\) has its collector fed from 15 V through \(R_C = 2.2\,\text{k}\Omega\), emitter grounded. 1. With \(I_B = 30\,\mu\text{A}\): assume active, \(I_C = 150 \times 30\,\mu\text{A} = 4.50\,\text{mA}\). 2. Then \(V_{CE} = 15 - 4.50 \times 2.2 = 5.10\,\text{V}\), well above 0.2 V, so the assumption holds. 3. With \(I_B = 60\,\mu\text{A}\): active mode would need 9.00 mA and give \(V_{CE} = -4.80\,\text{V}\), which is impossible. 4. So the transistor saturates, and the circuit sets the current: \(I_C = (15 - 0.2)/2.2\,\text{k}\Omega = 6.73\,\text{mA}\). 5. Check: saturation begins at \(6.73\,\text{mA}/150 = 44.8\,\mu\text{A}\), between the two base currents.

Common mistakes to avoid

First, applying \(I_C = \beta I_B\) without checking \(V_{CE}\): if the result needs more current than the load allows, the transistor is saturated. Second, giving a switch only the minimum base current; overdrive it so a low-β part still saturates. Third, omitting the base resistor, which lets the junction draw destructive current. Fourth, drawing electron-flow arrows: in an NPN, conventional current enters the base and collector. Fifth, assuming the middle pin is the base.

Key takeaways

A BJT has emitter, base and collector in NPN or PNP form, with \(I_E = I_B + I_C\) and the emitter arrow showing conventional current. A base-emitter forward bias of about 0.7 V lets base current control collector current. Cutoff is an open switch, saturation a closed one with \(V_{CE(sat)}\) near 0.2 V, and the active region regulates \(I_C = \beta I_B\), β typically 50 to 300. On diode check a good BJT shows two junctions sharing the base. To analyse a circuit, assume active mode and compute \(V_{CE}\); below about 0.2 V, use the saturation result.

Flashcards

Flashcard

BJT

Bipolar junction transistor: emitter, base, collector in NPN or PNP layers

A small base current controls a large collector current.

Test your understanding

Question 1 of 5

An NPN low-side switch must saturate a load drawing 100 mA. The data sheet guarantees β of at least 50. What is the minimum base current, before any overdrive?

Question 2 of 5

On diode check, red on pin 2 and black on pin 1 reads 0.69 V; red on pin 2 and black on pin 3 reads 0.67 V; all other combinations read OL. What is the transistor?

Question 3 of 5

An NPN with β = 200 has its collector fed from 10 V through 1.0 kΩ, emitter grounded, and a base current of 40 µA. What is its state?

Question 4 of 5

A transistor in active mode has a base current of 25 µA and a collector current of 3.0 mA. What are its emitter current and β?

Question 5 of 5

In an NPN transistor working in its active region, which way does conventional current flow at the terminals?

← Previous topicNext topic →