Electrical Engineering › Section P · Semiconductor theory, diodes, and transistors › Topic P.7
Special-purpose diodes: LEDs, photodiodes, Schottky, and others
Change the materials, the doping or the structure of a diode and it takes on a new job: switching faster, emitting light, detecting light, generating microwaves or acting as a voltage-controlled capacitor. This topic tours the family and the circuit rules that come with each member.
One junction, many jobs
So far every diode has been a silicon P-N junction used as a one-way switch, or a Zener in breakdown. The same structure, retuned, does much more. A metal-semiconductor junction gives the fast, low-drop Schottky diode; extreme doping gives the tunnel diode. Compound semiconductors turn current into light in LEDs and laser diodes, and photodiodes and solar cells turn light into current. Junction capacitance, exploited on purpose, gives the varactor. Each has its own circuit rules.
Schottky diodes
A Schottky diode is a junction between a metal and lightly doped n-type silicon rather than between p-type and n-type silicon. Its forward voltage is lower than a P-N diode's, typically about 0.2 to 0.5 V depending on current. Conducting with majority carriers only, it stores almost no minority charge, so its reverse recovery time is tiny and its capacitance small: the natural rectifier for switch-mode supplies at hundreds of kilohertz. The drawbacks: higher reverse leakage, which grows quickly with temperature, and lower reverse-voltage ratings in silicon, mostly below about 200 V. Silicon carbide Schottky diodes now extend the idea to over 1000 V.
Worked example: reverse-polarity protection
A gadget runs on 5.0 V at 2.0 A, and a series diode protects it if the supply is plugged in backwards. Assume typical drops at 2 A of 0.90 V for a silicon rectifier and 0.45 V for a Schottky. 1. Silicon: it wastes \(0.90 \times 2.0 = 1.8\) W and takes \(0.90/5.0 = 18\%\) of the supply voltage. 2. Schottky: \(0.45 \times 2.0 = 0.90\) W, or 9%. 3. Interpret: the Schottky halves the heat and leaves 4.55 V for the gadget instead of 4.10 V. 4. On a 48 V supply, 0.9 V would be under 2%; the lower the voltage, the more a drop costs. 5. The Schottky's higher leakage is harmless here, with only 5 V reverse.
Negative-resistance diodes
Some diodes have a region where current falls as voltage rises, a negative resistance that can feed energy into a resonant circuit and make it oscillate. The tunnel diode, discovered by Leo Esaki in the late 1950s, is doped about a thousand times more heavily than a rectifier, so its depletion region is thin enough for electrons to tunnel straight through; its current peaks at a low forward voltage, dips to a valley, then rises normally. It switches extremely fast but is now rare. The Gunn diode, only n-type gallium arsenide and not a junction at all, oscillates at microwave frequencies. The IMPATT diode, run in avalanche breakdown, generates higher microwave power but is noisy.
Light-emitting diodes
When electrons and holes recombine in a forward-biased junction, the energy released is about the band gap. In silicon it becomes heat; in compound semiconductors such as gallium arsenide phosphide or indium gallium nitride, much of it leaves as light, electroluminescence. The gap sets the colour through \(\lambda \approx 1240/E_g\) nm, so wider gaps give shorter wavelengths, and forward voltage rises from infrared, about 1.2 to 1.5 V, through red, about 1.6 to 2.2 V, to blue and white, about 3 V or more. Reverse ratings are low, often about 5 V. Efficient blue LEDs earned Isamu Akasaki, Hiroshi Amano and Shuji Nakamura the 2014 Nobel Prize in Physics; a white LED is a blue one coated with a yellow phosphor.
Worked example: driving LEDs
Run a white LED at 15 mA from 12.0 V, taking \(V_F = 3.1\) V. 1. Resistor: \(R = (12.0 - 3.1)/0.015 = 593\,\Omega\); the nearest E24 value, 620 Ω, gives \(8.9/620 = 14.4\) mA, close enough. 2. Resistor power: \(8.9^2/620 = 0.128\) W, more than a 1/8 W part should carry, so use 1/4 W. 3. Better: put three LEDs in series. \(R = (12.0 - 9.3)/0.015 = 180\,\Omega\), an E12 value, giving 15.0 mA and only 40.5 mW in the resistor. 4. Interpret: the LEDs now receive \(9.3/12 = 78\%\) of the supply power instead of 26%. 5. Rule: LEDs in parallel each need their own resistor, because their forward voltages never match exactly.
Laser diodes
A laser diode is an LED built with mirror-like ends so that emitted photons trigger further emission in step with themselves, stimulated emission. The result is coherent light: one wavelength, in phase, in a tight beam. Below a threshold current it glows dimly like an LED; above it, output rises steeply, so a small current error means a large change in light and risks instant damage. Laser diodes are therefore driven by regulated current sources, often steered by a monitor photodiode in the package. They carry fibre-optic data and read optical discs and barcodes. Even low-power beams can harm eyes.
Photodiodes and solar cells
A photodiode runs the LED in reverse: photons with at least the gap energy create electron-hole pairs, and the depletion region's field sweeps them apart as a photocurrent. Reverse biased (photoconductive mode), or held at zero volts, its current is proportional to light over many decades; a transimpedance amplifier turns that current into a voltage. Left open-circuit (photovoltaic mode), it develops its own voltage, which grows only logarithmically with light. PIN photodiodes add an intrinsic layer, lowering capacitance for gigahertz speeds; avalanche photodiodes add internal gain. A solar cell is a large photodiode delivering power: a silicon cell gives about 0.5 to 0.6 V, so modules wire dozens in series. Modern silicon modules convert about a fifth of sunlight.
Varactors and RF diodes
A reverse-biased junction is a capacitor whose depletion region is the dielectric, and more reverse voltage widens it and lowers the capacitance. A varactor, or varicap, exaggerates this so a control voltage can tune a resonant circuit. Since \(f = 1/(2\pi\sqrt{LC})\), a 4:1 capacitance change gives a 2:1 frequency change: with 2.2 µH, 40 pF resonates at 17.0 MHz and 10 pF at 33.9 MHz. Hyperabrupt types give larger ratios. The PIN switching diode, with an intrinsic layer between p and n, has very low capacitance and serves as an RF switch or, with varied forward current, an attenuator. The step-recovery or snap diode stops conducting abruptly, generating sharp pulses rich in harmonics.
More of the family
A constant-current diode is really a JFET with its gate tied to its source; it passes a fixed current of a few milliamperes over a wide voltage range, handy for driving LEDs. The Shockley diode is a four-layer thyristor that conducts once its breakover voltage is reached, covered in "Hysteresis, gas discharge tubes, the Shockley diode, and the DIAC". Silicon carbide diodes tolerate far higher temperatures and voltages than silicon and now appear in electric-vehicle chargers and solar inverters. Organic, carbon-based semiconductors are deposited at low temperature; organic LEDs, OLEDs, are now common in phone and television displays.
Common mistakes to avoid
First, connecting an LED without current limiting; its current rises steeply above \(V_F\) and destroys it. Second, sharing one resistor between parallel LEDs. Third, exceeding an LED's low reverse rating. Fourth, using a Schottky in a high-voltage or hot circuit without checking leakage and rating. Fifth, driving a laser diode from a voltage source. Sixth, expecting photodiode voltage, not current, to track light. Seventh, assuming frequency changes in the same ratio as capacitance.
Key takeaways
Schottky diodes, metal-semiconductor junctions, drop about 0.2 to 0.5 V and recover almost instantly, but leak more and block less. Tunnel, Gunn and IMPATT diodes use negative resistance to oscillate. LEDs emit at λ ≈ 1240/E_g nm, with V_F from about 1.6 V (red) to 3 V or more (blue, white), and need a series resistor, R = (V_S − V_F)/I. Laser diodes need regulated current. Photodiodes give current proportional to light; solar cells give about 0.5 to 0.6 V each. Varactors tune circuits, with f changing as the square root of C. Constant-current, SiC and organic diodes complete the family.
Flashcards
Flashcard
A metal-semiconductor junction with low V_F and almost no recovery time
Test your understanding
Question 1 of 5
A red LED with V_F = 2.0 V must run at 10 mA from a 9.0 V supply. What series resistance gives exactly 10 mA?
Question 2 of 5
Why are Schottky diodes favoured as rectifiers in low-voltage switch-mode supplies?
Question 3 of 5
For a light meter that must respond in proportion to light over many decades, how should a photodiode be operated?
Question 4 of 5
A varactor's capacitance is varied over a 4:1 range in an LC tuned circuit. Over what range does the resonant frequency change?
Question 5 of 5
Which of these LEDs typically has the highest forward voltage?
