Electrical Engineering › Section E · Methods of analysis (dc) › Topic E.5
Bridge networks and Y-delta conversions
The bridge is the classic network that no series or parallel step can simplify. It is also one of the most useful circuits in measurement. This topic analyses bridges, states the balance condition behind the Wheatstone bridge, and introduces the Y-delta conversions that turn a bridge back into a series-parallel network.
A network that will not reduce
Try to find the resistance seen by the source in a bridge and you get stuck at once: no two resistors share a current on their own, and no two sit across the same pair of nodes. Series-parallel reduction has nothing to work on. The methods of this section still apply, and mesh or nodal analysis will solve any bridge. But bridges are common enough to deserve their own tools. When a bridge is balanced, one resistor can be ignored entirely. When it is not, a Y-delta conversion rearranges three of its resistors into an equivalent shape that series and parallel steps can finish.
The bridge network
Describe a bridge by its four nodes. The source connects between the top node a (+) and the bottom node, ground. Resistor \(R_1\) runs from a to the left node b, \(R_2\) from a to the right node c, \(R_3\) from b to ground and \(R_4\) from c to ground. A fifth resistor \(R_5\), the bridge arm, joins b and c. So there are two dividers side by side, \(R_1\) over \(R_3\) and \(R_2\) over \(R_4\), with \(R_5\) linking their midpoints. Drawn as a diamond, a rectangle or a lattice, the network can look quite different, so identify it by its connections: four nodes, five resistors, and one resistor bridging two midpoints.
Worked example: an unbalanced bridge
Let \(E = 12\,\text{V}\), \(R_1 = 1.0\), \(R_2 = 2.2\), \(R_3 = 3.3\), \(R_4 = 1.5\) and \(R_5 = 4.7\,\text{k}\Omega\). Use nodal analysis, in kΩ, mA and V, with a fixed at 12 V. 1. Node b: \(\frac{V_b - 12}{1.0} + \frac{V_b}{3.3} + \frac{V_b - V_c}{4.7} = 0\). 2. Node c: \(\frac{V_c - 12}{2.2} + \frac{V_c}{1.5} + \frac{V_c - V_b}{4.7} = 0\). 3. Solving: \(V_b = 8.69\,\text{V}\) and \(V_c = 5.47\,\text{V}\). 4. Bridge-arm current: \((8.69 - 5.47)/4.7 = 0.683\,\text{mA}\) from b to c. 5. Source current:
so the bridge presents \(R_T = 12 / 6.28 = 1.91\,\text{k}\Omega\) to the source.
The balance condition
A bridge is balanced when the bridge arm carries no current. That happens when b and c sit at the same voltage, which means the two dividers have the same ratio:
The cross products of opposite arms are equal. With 1.0 kΩ over 1.5 kΩ on the left and 2.2 kΩ over 3.3 kΩ on the right, both ratios are 2:3 and both midpoints sit at 7.2 V from a 12 V source. In a balanced bridge \(R_5\) has no effect at all: replace it with an open circuit or a short circuit and nothing else changes, so the network reduces to two simple dividers in parallel.
The Wheatstone bridge
Put a sensitive current detector in the bridge arm and the balance condition becomes a way to measure resistance. With an unknown \(R_x\) in place of \(R_4\), adjust a calibrated resistor \(R_3\) until the detector reads zero, then \(R_x = R_2R_3 / R_1\). For instance, with \(R_1 = 1.0\,\text{k}\Omega\) and \(R_2 = 10\,\text{k}\Omega\), a null at \(R_3 = 472\,\Omega\) means \(R_x = 4.72\,\text{k}\Omega\). The reading does not depend on the source voltage, and detecting zero is easier than reading a value accurately. Samuel Hunter Christie described the circuit in about 1833, and Charles Wheatstone popularised it in about 1843. Today bridges read strain gauges and other resistive sensors, where a tiny resistance change gives a small, measurable imbalance.
Delta and Y networks
Three resistors can join three terminals, a, b and c, in two ways. In a delta (Δ), also drawn as a pi (π), each resistor connects one pair of terminals: \(R_{ab}\), \(R_{bc}\) and \(R_{ca}\). In a Y, also called a star or tee (T), each resistor runs from one terminal to a shared central point: \(R_a\), \(R_b\) and \(R_c\). A bridge contains both shapes; its top three resistors, \(R_1\), \(R_2\) and \(R_5\), form a delta between a, b and c. For any delta there is a Y that behaves identically at the three terminals, and the reverse is also true. Replacing one by the other can turn an irreducible network into a series-parallel one.
The conversion formulas
Delta to Y: each Y resistor equals the product of the two delta resistors that touch its terminal, divided by the sum of all three:
and likewise for \(R_b\) and \(R_c\). Y to delta: each delta resistor equals the sum of the pairwise products of the Y resistors, divided by the Y resistor opposite it:
For three equal resistors the formulas reduce to \(R_Y = R_\Delta / 3\) and \(R_\Delta = 3R_Y\). A quick check: a Y resistor is always smaller than either delta resistor touching its terminal.
Worked example: removing the bridge by conversion
Convert the top delta of the unbalanced bridge, \(R_{ab} = R_1 = 1.0\), \(R_{ac} = R_2 = 2.2\) and \(R_{bc} = R_5 = 4.7\,\text{k}\Omega\), into a Y. 1. Sum: \(7.9\,\text{k}\Omega\). 2. \(R_a = 1.0 \times 2.2 / 7.9 = 0.278\,\text{k}\Omega\), \(R_b = 1.0 \times 4.7 / 7.9 = 0.595\,\text{k}\Omega\) and \(R_c = 2.2 \times 4.7 / 7.9 = 1.31\,\text{k}\Omega\). 3. Now \(R_a\) runs from a to the centre, and two paths lead from the centre to ground: \(R_b + R_3 = 3.89\,\text{k}\Omega\) and \(R_c + R_4 = 2.81\,\text{k}\Omega\). 4. In parallel: \(1.63\,\text{k}\Omega\). 5. \(R_T = 0.278 + 1.63 = 1.91\,\text{k}\Omega\) and \(I_s = 6.28\,\text{mA}\), matching the nodal result exactly.
Common mistakes to avoid
First, mistaking a bridge for a series-parallel network because of how it is drawn; check the nodes. Second, writing the balance condition with the wrong pairs: the ratio of the two left arms must equal the ratio of the two right arms, or the cross products of opposite arms must match. Third, in a delta-to-Y conversion, dividing by the wrong quantity: always the sum of all three delta resistors. Fourth, in Y-to-delta, dividing by an adjacent Y resistor instead of the opposite one. Fifth, expecting a converted network to show the original internal currents; only the terminal behaviour is preserved.
Key takeaways
A bridge is two dividers whose midpoints are joined by a fifth resistor; it cannot be reduced by series and parallel steps alone, but mesh or nodal analysis always works. It is balanced when \(R_1 / R_3 = R_2 / R_4\), or \(R_1R_4 = R_2R_3\); then the bridge arm carries no current and may be opened or shorted. The Wheatstone bridge uses that null to measure resistance, \(R_x = R_2R_3 / R_1\). Delta to Y: product of adjacent delta resistors over their sum. Y to delta: sum of pairwise products over the opposite Y resistor. Equal resistors: \(R_Y = R_\Delta / 3\).
Flashcards
Flashcard
Two dividers with a fifth resistor joining their midpoints
Test your understanding
Question 1 of 5
A bridge has R1 = 2.0 kΩ and R3 = 3.0 kΩ in the left divider and R2 = 4.0 kΩ in the right divider's top arm. What value of R4, the right divider's bottom arm, balances it?
Question 2 of 5
A Wheatstone bridge reaches a null with R1 = 1.0 kΩ, R2 = 100 Ω and R3 = 3.3 kΩ. What is the unknown Rx = R2R3 ÷ R1?
Question 3 of 5
A delta has Rab = 3.0 kΩ, Rbc = 6.0 kΩ and Rca = 3.0 kΩ. What is Ra in the equivalent Y?
Question 4 of 5
Three equal 2.7 kΩ resistors form a Y. What is each resistor of the equivalent delta?
Question 5 of 5
In a balanced bridge, what happens if the bridge-arm resistor is replaced by a short circuit?
