Electrical Engineering › Section G · Capacitors › Topic G.2
Capacitance, dielectrics, and capacitor types
A capacitor is two conductors with an insulator between them, and its capacitance says how much charge it holds for each volt. Plate area, spacing and the insulating material set that value, while the insulator also sets how much voltage the part can survive.
Charge per volt
Connect a dc source across two metal plates separated by an insulator and, for a moment, current flows: the source moves electrons off one plate and onto the other, leaving \(+Q\) on one and \(-Q\) on the other. Charge stops moving once the plate voltage equals the source voltage. After that the capacitor passes no steady dc current at all. The ratio of stored charge to voltage is the capacitance:
Its unit is the farad, F, one coulomb per volt. A farad is huge; most practical parts run from picofarads to millifarads. A 47 µF capacitor charged to 9.0 V holds \(47 \times 10^{-6} \times 9.0 = 423\,\mu\text{C}\).
Capacitance of parallel plates
The field results from The electric field give the capacitance of two flat plates of area \(A\) a distance \(d\) apart. The field between them is \(E = V/d\), and the flux density is \(D = Q/A\). The ratio \(D/E\) is the permittivity \(\varepsilon\) of the material in the gap, so \(Q/A = \varepsilon V/d\), and dividing by \(V\):
Larger plates hold more charge, closer plates give a stronger field for the same voltage, and a dielectric of higher permittivity stores more flux per volt. Doubling the area doubles \(C\); halving the gap also doubles it.
Dielectrics and permittivity
The insulator between the plates is the dielectric. In a field, its molecules polarise: their positive and negative charges shift slightly, lining up against the field and partly cancelling it. The source must then put more charge on the plates to reach the same voltage, so capacitance rises. The factor is the relative permittivity (dielectric constant) \(\varepsilon_r = \varepsilon/\varepsilon_0\). A vacuum has \(\varepsilon_r = 1\) and air about 1.0006. Typical approximate values: PTFE (Teflon) about 2.1, polyester film about 3.3, mica about 5 to 7, and some ceramics, based on barium titanate, from hundreds to several thousand.
Worked example: a parallel-plate capacitor
Two plates 10 cm by 10 cm sit 0.10 mm apart. 1. Air gap: \(A = 0.010\,\text{m}^2\), so
2. Fill the gap with a dielectric of \(\varepsilon_r = 5.0\), typical of mica: \(C = 5.0 \times 885\,\text{pF} = 4.43\,\text{nF}\). 3. At 50 V, the air version holds \(Q = CV = 44.3\,\text{nC}\) and the mica version \(221\,\text{nC}\). 4. Field check: \(E = 50/(0.10 \times 10^{-3}) = 500\,\text{kV/m}\), safely below the 3 MV/m at which air breaks down. Note how small the result is: plates the size of a hand give under a nanofarad.
Dielectric strength and voltage rating
Every dielectric has a dielectric strength, the field at which it breaks down and conducts. Breakdown usually destroys a solid dielectric by punching a carbonised hole through it. Air manages about 3 MV/m; solid films and mica are many times stronger. US datasheets often quote dielectric strength in volts per mil, where a mil is 0.001 inch or 25.4 µm, so air's value is about 75 V/mil. Because \(E = V/d\), a thinner dielectric gives more capacitance but breaks down at a lower voltage. Every capacitor therefore carries a working voltage rating, set well below breakdown, that must not be exceeded.
Worked example: thickness against capacitance
A designer wants 100 nF rated at 250 V, using a film with \(\varepsilon_r = 3.3\) and an assumed dielectric strength of 20 MV/m. 1. Minimum thickness: \(d = \frac{250}{20 \times 10^6} = 12.5\,\mu\text{m}\). 2. Allow a safety factor of 2: \(d = 25\,\mu\text{m}\). 3. Plate area from \(C = \varepsilon_r\varepsilon_0 A/d\):
4. Interpret: as a strip 2.0 cm wide that is 4.28 m long. That is why film capacitors are made from long metallised strips rolled into a compact cylinder.
Leakage and other imperfections
No dielectric is a perfect insulator, so a small leakage current flows through it. A real capacitor behaves like an ideal one in parallel with a very large leakage resistance, which slowly discharges it when it is left disconnected. Film and ceramic types leak very little; electrolytic capacitors leak the most. Real parts also have an equivalent series resistance (ESR) from their leads, plates and electrolyte, which heats them when large currents flow, and a tolerance: the actual value may differ from the marked one by 5%, 10%, 20% or more.
Types of capacitor
Ceramic capacitors are small and cheap, from picofarads to tens of microfarads; class 1 types such as C0G are very stable, while high-value class 2 types such as X7R change value with temperature and applied voltage. Film capacitors (polyester, polypropylene) are stable and precise. Mica gives excellent stability at small values. Aluminium and tantalum electrolytics pack large capacitance into a small volume but are polarised: the marked − lead must stay negative, and reversing them can make them fail, sometimes violently. Variable capacitors, with interleaved plates, tune radios. Supercapacitors reach thousands of farads at low voltage for short-term energy storage.
Markings and uses
Small capacitors use a three-digit code in picofarads: two figures and a power of ten. "104" is \(10 \times 10^4\,\text{pF} = 100\,\text{nF}\), and "472" is 4.7 nF. A following letter gives tolerance: J is ±5%, K is ±10% and M is ±20%. Electrolytics print their value and voltage directly. Uses follow from the properties: decoupling capacitors beside chips supply quick bursts of current; filter capacitors smooth rectified dc; coupling capacitors pass changing signals between stages while blocking dc; and capacitors set the timing of oscillators.
Common mistakes to avoid
First, forgetting to convert area to square metres and spacing to metres in \(C = \varepsilon A/d\); 10 cm by 10 cm is 0.010 m², not 100. Second, leaving out \(\varepsilon_r\), or using it without \(\varepsilon_0\). Third, thinking a thicker dielectric raises capacitance; it lowers it, though it raises the voltage the part can withstand. Fourth, reading "104" as 104 pF instead of 100 nF. Fifth, fitting an electrolytic backwards or running any capacitor above its rated voltage.
Key takeaways
Capacitance is charge per volt, \(C = Q/V\), in farads. For parallel plates \(C = \varepsilon_r\varepsilon_0 A/d\), so area and permittivity raise it and spacing lowers it. Dielectrics polarise and raise capacitance by \(\varepsilon_r\). Each dielectric breaks down above its dielectric strength, about 3 MV/m for air, so thinner dielectrics trade voltage rating for capacitance. Real capacitors have leakage, ESR and tolerance. Ceramic, film, mica, electrolytic, variable and supercapacitor types suit different jobs, and electrolytics are polarised.
Flashcards
Flashcard
Capacitance: charge stored per volt
Test your understanding
Question 1 of 5
A capacitor holds 26.4 µC of charge when 12 V is across it. What is its capacitance?
Question 2 of 5
The plates of a parallel-plate capacitor are given twice the area and moved to half the spacing, with the same dielectric. How does its capacitance change?
Question 3 of 5
A parallel-plate capacitor has plates of 0.020 m², 0.20 mm apart, with a dielectric of relative permittivity 4.0. What is its capacitance?
Question 4 of 5
A small ceramic capacitor is marked 473J. What are its value and tolerance?
Question 5 of 5
Which statement about aluminium electrolytic capacitors is correct?
