Electrical Engineering › Section G · Capacitors › Topic G.4
Capacitors in series and parallel, and stored energy
Capacitors combine by rules that look like the resistor rules turned inside out: parallel capacitances add, while series ones combine like parallel resistors. A charged capacitor also stores energy, half of C times V squared, which is useful in a camera flash and dangerous on a workbench.
Building the value you need
Capacitors come in standard values and voltage ratings, so designers often combine several to get a capacitance, a voltage rating or a charge they cannot buy in one part. Power supplies place many capacitors in parallel; high-voltage equipment stacks them in series. The rules follow directly from \(Q = CV\) and from Kirchhoff's laws, applied after the transients of Charging and discharging transients have died away, when every capacitor in a dc circuit is an open circuit and holds a steady charge. The second half of this topic asks where the energy goes.
Capacitors in parallel
Capacitors in parallel share the same voltage \(V\), because each connects across the same two nodes. Each stores its own charge, \(Q_k = C_kV\), and the total charge drawn from the source is the sum. Dividing by \(V\):
Physically, connecting capacitors side by side is like enlarging the plate area, and area adds. So parallel capacitances add like series resistances. The voltage rating of the bank is that of its lowest-rated member, since all see the same voltage. A 4.7 µF, a 2.2 µF and a 1.0 µF in parallel give 7.9 µF.
Capacitors in series
In a series string, charge drawn onto the first plate pushes an equal charge off the far plate of the first capacitor onto the next, and so on, so every capacitor in series carries the same charge \(Q\). Their voltages, \(V_k = Q/C_k\), add to the source voltage by KVL. Dividing that sum by \(Q\):
For two capacitors this is product over sum, \(C_T = \frac{C_1C_2}{C_1 + C_2}\). Series is like thickening the dielectric, so the total is smaller than the smallest capacitor. A 10 µF and a 15 µF in series give 6.0 µF.
How voltage divides in series
Since every series capacitor holds the same \(Q\) and \(V = Q/C\), the smallest capacitor takes the largest voltage. For two in series across \(E\):
Note that the other capacitor appears on top, the reverse of the resistor divider. Put 10 µF and 4.7 µF in series across 30 V and the 4.7 µF takes \(30 \times \frac{10}{14.7} = 20.4\,\text{V}\), the 10 µF only 9.59 V. Series strings raise the total voltage rating, but in practice leakage currents rather than capacitance often decide the sharing, so equal resistors are wired across each capacitor to balance the voltages.
Worked example: a series-parallel network
A 24 V source is connected across \(C_1 = 10\,\mu\text{F}\) in series with a parallel pair, \(C_2 = 22\,\mu\text{F}\) and \(C_3 = 4.7\,\mu\text{F}\). Find each voltage and charge once charging is complete. 1. Parallel pair: \(22 + 4.7 = 26.7\,\mu\text{F}\). 2. Total: \(C_T = \frac{10 \times 26.7}{36.7} = 7.28\,\mu\text{F}\). 3. Charge from the source: \(Q = 7.28 \times 24 = 175\,\mu\text{C}\), the charge on \(C_1\) and on the pair as a whole. 4. Voltages: \(V_1 = Q/C_1 = 17.46\,\text{V}\) (keeping an extra figure), so the pair has \(24 - 17.46 = 6.54\,\text{V}\). 5. Pair charges: \(Q_2 = 22 \times 6.54 = 144\,\mu\text{C}\) and \(Q_3 = 4.7 \times 6.54 = 30.7\,\mu\text{C}\). 6. Check: the full charge on the pair gives \(174.6/26.7 = 6.54\,\text{V}\) as well, and \(144 + 30.7 = 175\,\mu\text{C}\).
Energy stored in a capacitor
An ideal capacitor dissipates nothing; the energy delivered while it charges is stored in the electric field of its dielectric. Moving a small charge \(dq\) onto a capacitor already at voltage \(v = q/C\) takes energy \(v\,dq\), and adding up from 0 to \(Q\) gives the area of a triangle under the straight line \(v = q/C\):
in joules. The square matters: doubling the voltage on a capacitor stores four times the energy. That is why high-voltage capacitors are so much more dangerous than low-voltage ones of the same capacitance.
Worked example: energy in the network and a flash
1. In the series-parallel network, \(W_1 = \frac{1}{2} \times 10\,\mu\text{F} \times 17.46^2 = 1.52\,\text{mJ}\), \(W_2 = 0.470\,\text{mJ}\) and \(W_3 = 0.100\,\text{mJ}\). 2. Their sum, 2.10 mJ, equals \(\frac{1}{2}C_TE^2 = \frac{1}{2} \times 7.28\,\mu\text{F} \times 24^2\), a useful check. 3. A flash capacitor of 120 µF charged to 330 V stores \(\frac{1}{2} \times 120 \times 10^{-6} \times 330^2 = 6.53\,\text{J}\). 4. Released into the lamp in about 1 ms, that is an average power of roughly 6.5 kW, far beyond what the small battery could supply directly. The circuit gathers energy slowly and releases it quickly.
Half the energy is lost in charging
Charge a capacitor from a fixed source \(E\) through a resistor and the source delivers charge \(Q = CE\) at voltage \(E\), supplying energy \(QE = CE^2\). Only \(\frac{1}{2}CE^2\) ends up stored, so the other half is turned into heat in the resistance, whatever its value; a smaller resistor just wastes it faster. For the flash capacitor charged straight from a 330 V source, 13.1 J would be supplied to store 6.53 J. Real chargers reduce this loss by raising the voltage gradually. And stored energy remains after the power is switched off, so large capacitors must be safely discharged before anyone handles the circuit.
Stray capacitance and applications
Any two conductors close together form a capacitor, wanted or not. Stray capacitance appears between neighbouring wires and circuit-board tracks, between a transistor's terminals, and between the turns of a coil. It is usually only picofarads, harmless at dc, but at high frequencies it couples signals where they should not go and slows fast edges, so it must be considered in design. Deliberate uses of combining capacitors include parallel banks of decoupling and filter capacitors, series strings for high voltage, and capacitors connected across the mains in surge protectors and line filters, which shunt fast, high-frequency disturbances away from the equipment.
Common mistakes to avoid
First, combining capacitors with the resistor rules: parallel capacitances add and series ones combine reciprocally. Second, assuming series capacitors share voltage equally; the smallest takes the most. Third, using the resistor-divider pattern for series capacitors, with the capacitor of interest on top. Fourth, forgetting the ½ in \(W = \frac{1}{2}CV^2\), or squaring the charge instead of the voltage. Fifth, thinking a capacitor is safe once the supply is off; its stored energy remains until it is discharged.
Key takeaways
Parallel capacitors share one voltage and \(C_T = C_1 + C_2 + \cdots\). Series capacitors share one charge and \(1/C_T = 1/C_1 + 1/C_2 + \cdots\), so the total is below the smallest. In series, \(V = Q/C\), so the smallest capacitor takes the most voltage. Stored energy is \(W = \frac{1}{2}CV^2 = \frac{1}{2}QV = Q^2/(2C)\), growing with the square of voltage. Charging from a fixed source through resistance wastes as much energy as is stored. Stray capacitance exists between any nearby conductors and matters most at high frequencies.
Flashcards
Flashcard
C_T = C₁ + C₂ + …
Test your understanding
Question 1 of 5
Capacitors of 4.7 µF, 2.2 µF and 1.0 µF are connected in parallel. What is the total capacitance?
Question 2 of 5
A 10 µF capacitor and a 15 µF capacitor are connected in series. What is the total capacitance?
Question 3 of 5
A 10 µF and a 4.7 µF capacitor are in series across 30 V. Once they have charged, what voltage is across the 4.7 µF capacitor?
Question 4 of 5
How much energy does a 470 µF capacitor store when charged to 25 V?
Question 5 of 5
The voltage on a charged capacitor is raised from 50 V to 100 V. What happens to its stored energy?
