Electrical Engineering › Section H · Magnetic circuits and inductors › Topic H.7

Inductors in series and parallel, and stored energy

Inductors combine by the same rules as resistors, provided they do not share flux, and in steady dc they simply vanish into short circuits. What they leave behind is stored energy, ½LI², which power converters use on purpose and switches must survive.

Why combine inductors

Inductors come in standard values, so a designer who needs an odd value, a higher current rating or a spread of heat across several parts may connect two or more together. Analysing a circuit also means recognising inductors that are already in series or parallel and reducing them to one. Then there is the question this topic ends with: how much energy an inductor holds, which decides how big it must be and how dangerous it is to interrupt.

Inductors in series

Inductors in series carry the same current, so each has the same \(di/dt\). Their voltages add, \(v = L_1\,di/dt + L_2\,di/dt\), which is the voltage of a single inductor

L_T = L_1 + L_2 + \cdots + L_N

This is the same rule as for resistors in series. The total is always larger than any one inductor. In a real circuit each coil's winding resistance is also in series, so those resistances add too, and the combination behaves as \(L_T\) in series with the sum of the winding resistances.

Inductors in parallel

Inductors in parallel share the same voltage, and their currents add, so the rates of change add: \(di/dt = v/L_1 + v/L_2\). That gives

\frac{1}{L_T} = \frac{1}{L_1} + \frac{1}{L_2} + \cdots + \frac{1}{L_N}

again the resistor rule. For two inductors, \(L_T = L_1L_2/(L_1 + L_2)\), product over sum. For \(N\) equal inductors, \(L_T = L/N\). The total is always smaller than the smallest one. Notice that capacitors behave the other way round: they add in parallel and combine by reciprocals in series.

Worked example: reducing a network

Between terminals a and b, inductor \(L_1 = 22\,\text{mH}\) runs from a to node c. From node c to b are two branches in parallel: \(L_2 = 120\,\text{mH}\) alone, and \(L_3 = 47\,\text{mH}\) in series with \(L_4 = 33\,\text{mH}\). Find the inductance between a and b, assuming no coupling. 1. The series branch: \(47 + 33 = 80\,\text{mH}\). 2. That 80 mH in parallel with 120 mH gives

\frac{80 \times 120}{80 + 120} = 48\,\text{mH}

3. Add the series part: \(L_T = 22 + 48 = 70\,\text{mH}\). 4. Check: the parallel group, 48 mH, is below its smaller branch, 80 mH, as it must be, and the total lies above \(L_1\).

A warning about shared flux

Both rules assume the coils are uncoupled, meaning no flux from one passes through another. Wind two coils on the same core, or mount them close together, and they share flux. Each then induces a voltage in the other through their mutual inductance, \(M\), and the simple totals no longer hold: two coils in series give more than \(L_1 + L_2\) when their fluxes aid and less when they oppose. Transformers are built on this coupling, and the topic "Mutual inductance" and the transformer topics after it give the rules. When coupling is unwanted, designers space coils apart, mount them at right angles, or use toroids, which keep their flux inside the ring.

Circuits with L and C at dc steady state

Once a dc circuit has settled, after more than five time constants, every inductor carries a steady current, so \(v_L = 0\) and it can be replaced by a short circuit. Every capacitor carries no current, so it counts as an open circuit. The steady currents and voltages then come from ordinary dc analysis. A circuit holding both inductance and capacitance is second order. A series R-L-C transient is overdamped (slow, no overshoot) when \(R > 2\sqrt{L/C}\), critically damped (fastest without overshoot) when they are equal, and underdamped (it rings, oscillating as it decays) when \(R\) is smaller. The final steady state, though, needs only the short and open replacements.

Worked example: L and C in one circuit

A 12 V source has its + terminal at node a. Resistor \(R_1 = 10\,\Omega\) runs from a to node b, and a 100 µF capacitor from node b to ground. A 2.2 mH inductor runs from node b to node c, and \(R_2 = 22\,\Omega\) from node c to ground. Find the steady inductor current and capacitor voltage. 1. Short the inductor, so nodes b and c join; open the capacitor. 2. One loop remains: \(I_L = 12/(10 + 22) = 0.375\,\text{A}\). 3. The capacitor sits across \(R_2\): \(V_C = 0.375 \times 22 = 8.25\,\text{V}\). 4. Stored energies, using the formulas below: \(W_L = \tfrac{1}{2}(0.0022)(0.375)^2\), which is 0.155 mJ, and \(W_C = \tfrac{1}{2}(100 \times 10^{-6})(8.25)^2\), which is 3.40 mJ.

Energy stored by an inductor

While the current in an ideal inductor builds up, \(v_L\) and \(i_L\) are both positive, so the power \(p = v_Li_L\) flows in. None of it is dissipated; it is stored in the magnetic field. Adding up that power over the build-up, the area under the power curve, gives

W = \tfrac{1}{2}LI^2

in joules, where \(I\) is the final current. When the current falls, the same energy comes back out. The 470 mH coil carrying 120 mA in the topic "R-L transients" holds \(\tfrac{1}{2}(0.470)(0.120)^2 = 3.38\,\text{mJ}\), all turned to heat in the two resistors during its decay. Because \(W\) grows with \(I^2\), doubling the current quadruples the energy.

Capacitor and inductor side by side

The two storage elements are duals; swap \(v\) with \(i\) and \(C\) with \(L\) to turn one column into the other:

\begin{array}{ll} \text{Capacitor} & \text{Inductor} \\ \hline i_C = C\,dv_C/dt & v_L = L\,di_L/dt \\ v_C \text{ cannot jump} & i_L \text{ cannot jump} \\ \text{dc: open} & \text{dc: short} \\ W = \tfrac{1}{2}CV^2 & W = \tfrac{1}{2}LI^2 \\ \tau = RC & \tau = L/R \end{array}

The series and parallel rules swap as well, as the earlier cards showed.

Stored energy at work

A switch-mode power supply charges an inductor with current, then releases its energy into the output, thousands to millions of times a second. Each cycle moves about \(\tfrac{1}{2}LI^2\), so the inductor must reach its peak current without saturating, which sets its size. Chokes in mains filters and lamp dimmers slow sudden current changes and block high-frequency noise from switching parts. An ignition coil stores energy in its field and releases it as a high-voltage spark. Where release is unwanted, as with a relay coil, the stored energy is the reason for a flyback diode or discharge resistor.

Common mistakes to avoid

First, using the capacitor rules for inductors: inductors add in series and combine by reciprocals in parallel. Second, forgetting that the parallel total must be below the smallest value, a quick check on any answer. Third, ignoring mutual inductance when coils share a core. Fourth, at dc steady state, treating an inductor as an open circuit instead of a short. Fifth, writing \(W = LI\) or \(\tfrac{1}{2}LI\), leaving out the square. Sixth, assuming an ideal inductor uses up energy; it stores and returns it.

Key takeaways

Uncoupled inductors follow the resistor rules: \(L_T = L_1 + L_2 + \cdots\) in series, \(1/L_T = 1/L_1 + 1/L_2 + \cdots\) in parallel, product over sum for two and \(L/N\) for \(N\) equal parts. Coils that share flux need the mutual-inductance rules. At dc steady state, inductors become short circuits and capacitors open circuits. An ideal inductor stores \(W = \tfrac{1}{2}LI^2\) in its magnetic field and returns it when the current falls, the dual of a capacitor's \(\tfrac{1}{2}CV^2\). That energy sizes power-converter inductors and explains switching spikes.

Flashcards

Flashcard

Inductors in series

L_T = L₁ + L₂ + … + L_N

Same current; voltages add.

Test your understanding

Question 1 of 5

A 330 mH inductor and a 220 mH inductor are connected in parallel, with no coupling. What is the total inductance?

Question 2 of 5

How much energy does a 0.50 H inductor store when it carries a steady 2.0 A?

Question 3 of 5

Three uncoupled 60 mH inductors are connected in parallel. What is the total inductance?

Question 4 of 5

A 24 V source drives R₁ = 47 Ω from node a to node b, an inductor from node b to node c, and R₂ = 33 Ω from node c to ground, with a capacitor from node b to ground. What is the steady inductor current?

Question 5 of 5

Two uncoupled coils, 47 mH with 3.0 Ω of winding resistance and 100 mH with 5.0 Ω, are connected in series. What single coil is the pair equivalent to?

← Previous topicNext topic →