Electrical Engineering › Section I · Sinusoidal waveforms and phasors › Topic I.1
Sinusoidal waveforms and their general format
The voltage at a wall outlet does not sit at one value: it swings smoothly up and down sixty times a second. This topic gives you the vocabulary and the single equation used to describe that swing, and every ac topic after it builds on them.
From steady dc to alternating ac
So far every source in the course has been dc: a battery or supply whose voltage stays fixed once any transient has died away. Now the source itself changes with time in a set pattern. The most important pattern is the sinusoid, the smooth wave traced by a sine function. Power stations generate it, and audio, radio and control signals are built from it. Strictly, "ac" means alternating current, but engineers also say "ac voltage", and in this course an unqualified "ac" means sinusoidal.
Words that describe a waveform
A waveform is a graph of a quantity against time. Its value at any one instant is the instantaneous value, written in lower case: \(v(t)\) or \(i(t)\). The peak amplitude \(V_m\) is the largest value measured from the average level, here zero, and the peak value is the largest value measured from zero. For a pure sinusoid the two are equal. The peak-to-peak value \(V_{pp}\) runs from the positive peak to the negative peak, so \(V_{pp} = 2V_m\). A periodic waveform repeats itself; one complete repeat is a cycle, and the time a cycle takes is the period \(T\), in seconds.
Frequency and the hertz
Frequency \(f\) is the number of cycles completed each second. It is the reciprocal of the period:
Its unit is the hertz (Hz), one cycle per second. US mains runs at 60 Hz, so each cycle lasts \(1/60\) s, about 16.7 ms. Most of Europe, Africa, Asia and Australia use 50 Hz, a period of 20 ms. Human hearing spans roughly 20 Hz to 20 kHz, and radio uses kilohertz to gigahertz, where a period of \(0.25\,\mu\text{s}\) belongs to a 4 MHz signal.
Worked example: reading an oscilloscope trace
An oscilloscope shows a sinusoid with the horizontal scale at 0.5 ms per division and the vertical scale at 2 V per division. One full cycle spans 4 divisions, and the positive peak sits 3 divisions above the centre line. 1. Period: \(T = 4 \times 0.5\,\text{ms} = 2\,\text{ms}\). 2. Frequency: \(f = 1/T = 1/(2\,\text{ms}) = 500\,\text{Hz}\). 3. Peak value: \(V_m = 3 \times 2\,\text{V} = 6\,\text{V}\). 4. Peak-to-peak: \(V_{pp} = 2V_m = 12\,\text{V}\), which should cover 6 divisions on screen. 5. Check: 500 cycles of 2 ms each fill exactly one second, as they must.
The sine wave and the rotating vector
Picture an arrow of fixed length \(V_m\) pivoted at the origin and spinning anticlockwise at a steady rate. Its vertical projection, the height of its tip, is \(V_m \sin\alpha\), where \(\alpha\) is the angle it has turned through from the positive horizontal axis. Plot that height against \(\alpha\) and you trace a sine wave: one full turn is one cycle. This is close to what happens inside a generator, where a coil turns steadily in a magnetic field. Angles here are best measured in radians. One radian is the angle that cuts off an arc equal to the radius, and a full turn is \(2\pi\) rad, so \(\pi\) rad equals 180°.
Angular frequency
If the arrow turns at a steady angular velocity \(\omega\), in radians per second, the angle after time \(t\) is \(\alpha = \omega t\). One cycle, \(2\pi\) rad, takes one period, so
For 60 Hz mains, \(\omega = 2\pi \times 60 \approx 377\,\text{rad/s}\); for 50 Hz it is about 314 rad/s. Engineers call \(\omega\) the angular frequency. Keep \(f\) in hertz and \(\omega\) in radians per second: they describe the same wave but differ by the factor \(2\pi\).
The general format
This course writes every sinusoidal voltage and current in one form:
Here \(V_m\) is the peak value, \(\omega\) the angular frequency and \(\theta\) the phase angle, the angle the wave has already reached at \(t = 0\). When \(\omega\) is a number, \(\omega t\) is in radians, so \(\theta\) must be too: a 30° phase angle appears as \(\pi/6\). With a symbolic \(\omega t\), a degree angle such as \(\sin(\omega t + 30^\circ)\) is also accepted. A positive \(\theta\) shifts the wave to the left, so it reaches each peak earlier; a negative \(\theta\) shifts it right. For example, \(v(t) = 10 \sin(1000t + \pi/3)\,\text{V}\) starts at \(10\sin(\pi/3) = 8.66\,\text{V}\) and first peaks at \(t = 0.524\,\text{ms}\).
Polarity and direction
A sinusoid is positive for half of each cycle and negative for the other half, so a sign only means something against a reference. A source between nodes a and b is marked with a + at a and a − at b. When \(v(t)\) is positive, node a is at the higher potential; when it is negative, b is higher. A current \(i(t)\) is drawn with a reference arrow. This course uses conventional current, the flow of positive charge, so a positive \(i(t)\) means current in the arrow's direction, and a negative value means it flows the other way. The references stay fixed while the wave reverses.
Worked example: instantaneous values
A source produces \(v(t) = 170 \sin(377t)\,\text{V}\). Find its frequency, period and the voltage at \(t = 2\,\text{ms}\), and when it first reaches 100 V. 1. Frequency: \(f = \omega/2\pi = 377/2\pi \approx 60.0\,\text{Hz}\), so \(T \approx 16.7\,\text{ms}\). 2. Angle at 2 ms: \(\omega t = 377 \times 0.002 = 0.754\,\text{rad}\). 3. Value, with the calculator in radian mode: \(v = 170 \sin(0.754) = 116\,\text{V}\). 4. First time at 100 V: \(\sin(377t) = 100/170\), so \(377t = 0.629\,\text{rad}\) and \(t = 1.67\,\text{ms}\). 5. Check: the first peak comes a quarter period in, at 4.17 ms, so 116 V at 2 ms, while still rising, is sensible.
Why sinusoids matter
Three facts make the sinusoid the standard ac waveform. First, a coil turning steadily in a uniform magnetic field generates it naturally, which is why power systems produce it. Second, a linear circuit of resistors, inductors and capacitors driven by a sinusoid responds, once transients have died away, with sinusoids of the same frequency: only the peak values and phase angles change. Third, by Fourier analysis almost any periodic waveform, such as a square wave, can be built from sinusoids of different frequencies, as the topic "Fourier series and nonsinusoidal circuits" shows.
Common mistakes to avoid
First, leaving the calculator in degree mode while evaluating \(\sin(377t)\): the argument is in radians. Second, confusing \(f\) and \(\omega\), for instance writing \(\sin(60t)\) for a 60 Hz wave instead of \(\sin(377t)\). Third, mixing a degree phase angle into a radian argument, as in \(\sin(377t + 30)\); convert 30° to \(\pi/6\) first. Fourth, calling the peak-to-peak value the peak value, which doubles every later answer. Fifth, reading the sign of \(v(t)\) without checking the polarity marks it refers to.
Key takeaways
A sinusoid is described by its peak value V_m, its period T and frequency f = 1/T in hertz, and its phase angle. The peak-to-peak value is 2V_m. Angular frequency is ω = 2πf in radians per second, about 377 rad/s for 60 Hz. The course's general format is v(t) = V_m sin(ωt + θ), with θ in radians whenever ω is a number; positive θ shifts the wave earlier. Lower-case v and i are instantaneous values, measured against fixed polarity marks and conventional-current arrows. Sinusoids matter because generators produce them, linear circuits preserve their frequency, and other waveforms are built from them.
Flashcards
Flashcard
The value at one instant, written v(t) or i(t)
Test your understanding
Question 1 of 5
An oscilloscope shows one full cycle of a sinusoid across 5 divisions at 0.2 ms per division. What is the frequency?
Question 2 of 5
What is the angular frequency of a 50 Hz sinusoid?
Question 3 of 5
For v(t) = 20 sin(1000t) V, what is v at t = 1 ms?
Question 4 of 5
A sinusoid measures 24 V peak-to-peak. What is its peak value?
Question 5 of 5
How does v(t) = 5 sin(ωt + π/4) compare with 5 sin(ωt)?
