Electrical Engineering › Section E · Methods of analysis (dc) › Topic E.1

Current sources and source conversions

A voltage source fixes a voltage and lets the circuit decide the current. A current source does the reverse. Learning how current sources behave, and how to swap a practical voltage source for an equivalent current source, gives you the tools the analysis methods of this section rely on.

The dual of a voltage source

Every source so far has been a voltage source: it holds its terminal voltage and the connected network sets the current. A current source is its dual. It holds the current through its terminals fixed, and the network sets the voltage across it. Transistor circuits approximate current sources closely, and they appear inside integrated circuits, battery chargers, LED drivers and the sensor loops of some alarm systems, where a steady current flows round a loop of door and window switches and any break is detected at once. In analysis, current sources also make some problems much simpler, which is why the methods that follow, from "Branch-current analysis" onwards, need them.

The ideal current source

An ideal current source delivers its rated current whatever is connected to it. Its symbol is a circle containing an arrow that shows the direction of that current. A 5 mA source driving a 2.2 kΩ resistor develops \(5\,\text{mA} \times 2.2\,\text{k}\Omega = 11\,\text{V}\) across it; swap in 4.7 kΩ and the same source develops 23.5 V, still at 5 mA. Two consequences follow. Any element in series with a current source carries exactly the source current. And the voltage across the source itself must be found from the rest of the circuit, usually with KVL. A real current source can only supply its current up to a limited voltage, its compliance voltage, so it cannot drive an open circuit.

Worked example: current sources in simple circuits

Part A: a 12 mA current source feeds node a, and \(R_1 = 1.5\,\text{k}\Omega\) and \(R_2 = 3.0\,\text{k}\Omega\) run from a to ground. 1. The resistors are in parallel: \(1.0\,\text{k}\Omega\). 2. \(V_a = 12\,\text{mA} \times 1.0\,\text{k}\Omega = 12\,\text{V}\). 3. \(I_1 = 12 / 1.5\,\text{k} = 8\,\text{mA}\) and \(I_2 = 4\,\text{mA}\); check \(8 + 4 = 12\). Part B: a 2 mA source pushes current up from ground to node a, through 1.8 kΩ to node b, into the + terminal of a 9 V battery and out of its − terminal to ground. 4. The loop current is 2 mA, whatever the battery. 5. KVL: \(V_a = 9 + (2\,\text{mA})(1.8\,\text{k}\Omega) = 12.6\,\text{V}\). 6. Powers: the source delivers 25.2 mW, the battery absorbs 18 mW and the resistor 7.2 mW.

Practical sources

No real source is ideal. A practical voltage source, as "Internal resistance and voltage regulation" showed, is an ideal source \(E\) in series with an internal resistance, there called \(R_{int}\) and here \(R_s\), so its terminal voltage sags as the load current rises. A practical current source is modelled the other way round: an ideal current source \(I\) in parallel with an internal resistance \(R_p\). Some of the source current leaks through \(R_p\) instead of the load, and the leak grows as the load resistance rises. A good current source has a very large \(R_p\), just as a good voltage source has a very small \(R_s\). An ideal current source is the limit \(R_p \to \infty\).

Source conversions

A practical voltage source and a practical current source can be made to behave identically at their terminals. The rule is

I = \frac{E}{R_s}, \qquad R_p = R_s

and in reverse \(E = IR_p\). The current arrow must point towards the terminal that was +, so that both versions push current out of the same terminal into a load. The check is quick: shorting the terminals gives \(E / R_s\) from the voltage version and all of \(I\) from the current version, while open terminals give \(E\) and \(IR_p\). The equivalence holds only at the external terminals. Inside, the two models dissipate different powers, so never use a converted model to find the source's own losses.

Worked example: checking a conversion

Convert an 18 V source with \(R_s = 1.2\,\text{k}\Omega\) into a current source, and compare both with a 3.3 kΩ load. 1. \(I = 18 / 1.2\,\text{k} = 15\,\text{mA}\), with \(R_p = 1.2\,\text{k}\Omega\) in parallel. 2. Voltage form: \(I_L = 18 / (1.2 + 3.3)\,\text{k} = 4.0\,\text{mA}\), so \(V_L = 13.2\,\text{V}\). 3. Current form, by the current divider rule: \(I_L = 15 \times \frac{1.2}{1.2 + 3.3} = 4.0\,\text{mA}\). The load cannot tell the difference. 4. Internal power: in the voltage form \(R_s\) dissipates \((4.0\,\text{mA})^2(1.2\,\text{k}\Omega) = 19.2\,\text{mW}\), but in the current form \(R_p\) has 13.2 V across it and dissipates 145 mW. The models agree outside and differ inside.

Current sources in parallel and in series

Current sources in parallel combine by KCL: add the currents pointing into a node and subtract those pointing out, and combine their internal resistances in parallel. An 8 mA source into node a and a 3 mA source out of a give a single 5 mA source into a. With 2.0 kΩ and 3.0 kΩ also from a to ground, their 1.2 kΩ combination gives \(V_a = 6.0\,\text{V}\). Current sources in series are another matter. KCL demands one current in a series path, so two ideal current sources of different values can never be in series, just as unequal ideal voltage sources can never be in parallel. Equal ones in series are allowed but pointless.

Worked example: combining sources by conversion

Two practical sources feed node a: 12 V with 2.0 kΩ in series and 9 V with 3.0 kΩ in series, both + towards a. A 1.2 kΩ load runs from a to ground. Find \(V_a\). 1. Convert: \(12 / 2.0\,\text{k} = 6\,\text{mA}\) with 2.0 kΩ in parallel, and \(9 / 3.0\,\text{k} = 3\,\text{mA}\) with 3.0 kΩ in parallel, both into a. 2. Combine sources: \(6 + 3 = 9\,\text{mA}\). 3. Combine resistors: \(2.0 \parallel 3.0 \parallel 1.2 = 0.60\,\text{k}\Omega\). 4. \(V_a = 9\,\text{mA} \times 0.60\,\text{k}\Omega = 5.4\,\text{V}\), and the load current is 4.5 mA. 5. Check in the original circuit: the 12 V source supplies \((12 - 5.4)/2.0\,\text{k} = 3.3\,\text{mA}\) and the 9 V source \((9 - 5.4)/3.0\,\text{k} = 1.2\,\text{mA}\), and \(3.3 + 1.2 = 4.5\,\text{mA}\).

Common mistakes to avoid

First, assuming the voltage across a current source is zero, or equal to some nearby source; it must be found from the circuit. Second, converting with the wrong arrow direction: the current must point towards the original + terminal. Third, keeping the series resistor in series after converting; it moves into parallel with the current source. Fourth, using a converted model to compute the power lost inside the source. Fifth, placing unequal current sources in series, which breaks KCL. Sixth, forgetting that an element in series with a current source carries the source current exactly.

Key takeaways

An ideal current source fixes its current; its voltage is set by the network. Any element in series with it carries that current. A practical voltage source is \(E\) in series with \(R_s\); a practical current source is \(I\) in parallel with \(R_p\). Convert with \(I = E / R_s\) and \(R_p = R_s\), arrow towards the former + terminal; the two agree only at the terminals. Parallel current sources add algebraically, with their resistances in parallel. Unequal current sources may never be placed in series.

Flashcards

Flashcard

Ideal current source

Fixed current whatever the load; voltage set by the network

Dual of a voltage source.

Test your understanding

Question 1 of 5

A 9 V source with 450 Ω internal resistance is converted to an equivalent current source. What is the result?

Question 2 of 5

A 4 mA ideal current source drives a 3.3 kΩ resistor. The resistor is replaced by a 6.8 kΩ resistor. What is the current now?

Question 3 of 5

A 3 mA current source pushes current up from ground into node a, through a 2.0 kΩ resistor to node b, into the + terminal of a 5 V battery and out of its − terminal to ground. What is the voltage at node a?

Question 4 of 5

A 10 mA current source points into node a, and a 4 mA current source points out of node a. Resistors of 3.3 kΩ and 2.2 kΩ run from a to ground. What is Va?

Question 5 of 5

Why can two ideal current sources of 2 mA and 5 mA never be connected in series?

← Previous topicNext topic →