Electrical Engineering › Section P · Semiconductor theory, diodes, and transistors › Topic P.4

Diode basics, meter checks, ratings, and rectifier circuits

A diode is a one-way valve for current, and its most important job is rectification: turning the alternating voltage from the mains into the one-directional voltage electronics need. This topic covers how a diode behaves in a circuit, how to test one, how to read its ratings, and the rectifier circuits built from it.

A one-way valve

"Electrons, holes, the P-N junction, and junction diodes" explained why a junction conducts one way. In a circuit, the simplest picture is a self-operating switch: closed when forward biased, with the anode more positive than the cathode, and open when reverse biased. In series with a 12 V battery and a lamp, the diode lights the lamp one way round; reversed, it drops the whole 12 V and the lamp stays dark. Small-signal parts are just called diodes; power parts, from about 1 A up, are often called rectifiers.

Forward voltage and simple models

Unlike a closed switch, a conducting diode drops a noticeable voltage, its forward voltage \(V_F\). For silicon it stays near 0.7 V over a wide range of currents; for germanium it is about 0.3 V. The ideal-diode model is a perfect switch with no drop. The constant-drop model, this course's default, treats a conducting silicon diode as a fixed 0.7 V and a reverse-biased one as an open circuit. The diode equation, next, is the most exact. Forward voltage also falls as the junction warms, by roughly 2 mV per °C, so a diode can sense temperature.

The diode equation

The exponential shape of the curve is captured by the Shockley diode equation:

I_D = I_S\left(e^{V_D/(nV_T)} - 1\right)

Here \(I_S\) is the saturation current, a tiny constant, often around \(10^{-14}\) A in small silicon diodes; n is the emission coefficient, 1 to 2; and \(V_T = kT/q\) is the thermal voltage, about 25.9 mV at 300 K. Once \(V_D\) exceeds about 0.1 V the −1 is negligible, and the current rises by a factor of e for every \(nV_T\) of extra voltage. Turn that around: each tenfold rise in current needs only \(nV_T \ln 10\) more volts, about 60 mV when n = 1.

Worked example: how little the drop changes

A silicon diode with n = 1 drops 0.620 V at 1.0 mA. Estimate its drop at 10 mA and 100 mA. 1. Voltage per decade: \(V_T \ln 10 = 0.02585 \times 2.303 = 0.0595\) V. 2. At 10 mA, one decade up: \(0.620 + 0.060 = 0.680\) V. 3. At 100 mA, two decades up: \(0.620 + 0.119 = 0.739\) V. 4. Interpret: a hundredfold change in current moved the drop by only about 0.12 V, which is why the constant 0.7 V model works for most analysis. 5. Caution: real diodes add a little bulk resistance, so at high currents the drop climbs faster than the equation predicts.

Checking a diode with a meter

An ohmmeter shows a diode's one-way nature: low resistance one way, very high or "OL" the other. The low reading itself means little, since it depends on the meter's test current, and you must know which lead is positive: the red one on most digital meters, but the black one on some analog meters' resistance ranges. A diode-test setting is better. It pushes about 1 mA and displays the forward voltage, typically 0.5 to 0.7 V for silicon with the red lead on the anode. Near 0 V both ways means a shorted diode; OL both ways, an open one. Some resistance ranges use under 0.3 V, too little to turn a junction on.

Reading a datasheet

\(V_{RRM}\) is the largest repetitive reverse voltage, often called the peak inverse voltage (PIV), and \(V_R\) the largest continuous one. \(I_{F(AV)}\) is the largest average forward current and \(I_{FSM}\) a much larger one-off surge, allowed because the junction takes time to heat. \(V_F\) is the forward voltage at a stated current, \(I_R\) the reverse leakage, \(C_J\) the junction capacitance, and \(t_{rr}\) the reverse recovery time, how long conduction continues after reversal: microseconds for ordinary rectifiers, nanoseconds for fast switching diodes. Heat sets most limits: \(T_J = T_A + P R_{\theta JA}\), so 0.9 W in a package rated 50 °C/W at 25 °C ambient puts the junction at 70 °C. The 1N4001 to 1N4007 family, for example, has maximum ratings of 1 A average, 30 A surge and 50 to 1000 V.

Half-wave rectification

Rectification converts ac to dc. The simplest rectifier is a single diode in series with the load: it conducts on the half-cycles that make its anode positive and blocks the others, so the load sees one-polarity pulses, one per cycle. With an ideal diode and peak input \(V_p\), the average output is \(V_p/\pi\), only 32% of the peak, and with a fixed resistance the load receives exactly half the power of full ac. Some two-level lamp dimmers once worked this way. As a power supply it is poor: half of each cycle is wasted, and widely spaced pulses are hard to smooth.

Full-wave: centre-tap and bridge

Full-wave rectifiers use both half-cycles, giving two pulses per cycle and an ideal average of \(2V_p/\pi\). The centre-tap circuit takes its negative output from a centre-tapped secondary, with two diodes from the winding ends to the positive output. Each half-cycle, one half-winding drives current through one diode, so the output loses one drop; but each idle diode must block nearly twice the half-winding's peak. The bridge rectifier uses four diodes and an ordinary winding. Current passes through two diodes each half-cycle, costing two drops, but each diode blocks only about one peak. Bridges are the usual choice.

Worked example: a bridge from a 12 V winding

A bridge of silicon diodes is fed from a 12.0 V rms, 60 Hz transformer secondary and drives a 100 Ω load. 1. Peak input: \(V_p = 12.0\sqrt{2} = 16.97\) V. 2. Peak output, two drops: \(16.97 - 1.4 = 15.57\) V. 3. Average: the ideal formula gives \(2V_p/\pi = 10.8\) V; averaging the waveform with the diode drops included gives about 9.44 V, or about 94 mA in the load. 4. Pulses: two per cycle, 120 Hz. 5. Diode stress: each off diode blocks about \(16.97 - 0.7 = 16.3\) V, so a 50 V part is ample. 6. Compare: a 12-0-12 V centre-tap circuit gives 16.27 V peak, but each diode blocks about 33 V.

Polyphase rectifiers

A rectifier can be described by its pulse number, the dc pulses per ac cycle: 1 for half-wave, 2 for any single-phase full-wave circuit. A three-phase bridge uses six diodes, a pair per line, one steering current to the positive output and one to the negative. Its output is 6-pulse: on 60 Hz the ripple is at 360 Hz and small, because the overlapping phases never let the output fall far. A Y-Δ transformer shifts its outputs 30° from a Y-Y one, so two bridges fed this way give 12 pulses. Less ripple means smaller filters, vital at high power. Capacitor filters for single-phase rectifiers come in "Peak detectors, clippers, clampers, and voltage multipliers".

Common mistakes to avoid

First, forgetting the drop: a bridge loses about 1.4 V, which matters in low-voltage supplies. Second, using rms where the peak belongs; a 12 V rms winding peaks at 17 V. Third, sizing centre-tap diodes for one peak instead of two. Fourth, treating an ohmmeter's forward "resistance" as a real diode property. Fifth, assuming every meter's red lead is positive on resistance ranges. Sixth, confusing average current with surge current, allowed only briefly.

Key takeaways

A diode conducts when its anode is more positive than its cathode; silicon drops about 0.7 V, germanium about 0.3 V. The diode equation, I_D = I_S(e^(V_D/nV_T) − 1) with V_T ≈ 25.9 mV, means each tenfold rise in current adds only about 60 mV. A diode-test meter reads the forward voltage and shows shorts and opens. Key ratings: V_RRM, I_F(AV), I_FSM, V_F, I_R, t_rr and thermal resistance. Half-wave rectifiers give one pulse per cycle and V_p/π average; centre-tap and bridge rectifiers give two pulses and 2V_p/π; three-phase bridges give six.

Flashcards

Flashcard

Forward bias

Anode more positive than cathode: the diode conducts

Reverse bias blocks.

Test your understanding

Question 1 of 5

A silicon diode with n = 1 drops 0.64 V at 2 mA. About what does it drop at 20 mA?

Question 2 of 5

A bridge rectifier of silicon diodes is fed from an 18 V rms winding. What is its peak output voltage?

Question 3 of 5

In a centre-tap full-wave rectifier, each half of the secondary peaks at 20 V. About what reverse voltage must each diode withstand?

Question 4 of 5

A meter on diode test reads 0.58 V one way and OL the other way across a diode. What does this show?

Question 5 of 5

How many output pulses per ac cycle does a three-phase full-wave bridge rectifier produce?

← Previous topicNext topic →