Electrical Engineering › Section P · Semiconductor theory, diodes, and transistors › Topic P.5

Peak detectors, clippers, clampers, and voltage multipliers

Pair a diode with a capacitor or a reference voltage and it stops being just a rectifier. It can hold a peak, cut off part of a wave, shift a whole wave up or down, or stack peaks into a higher dc voltage.

Shaping waves with diodes

"Diode basics, meter checks, ratings, and rectifier circuits" used diodes to turn ac into pulsing dc. Four more circuit families use the same one-way switching, analysed here with the constant 0.7 V model, one half-cycle at a time. A peak detector holds a capacitor at the highest value a wave reaches. A clipper cuts off the part of a wave beyond a set level. A clamper shifts a whole wave so one peak sits at a chosen level. A voltage multiplier combines clampers and peak detectors to give several times the input peak.

The peak detector

A peak detector is a diode in series with a capacitor, with the output taken across the capacitor. On the rising part of each positive half-cycle the diode conducts and charges the capacitor to the input peak less one drop, \(V_p - 0.7\) V. When the input falls below that, the diode is reverse biased and the capacitor has nowhere to discharge, so it holds the peak. The circuit is simply a half-wave rectifier with a smoothing capacitor. A load drains the capacitor a little between peaks and the diode tops it up each cycle; that sag, the ripple, stays small if \(R_LC\) is much longer than the period.

Worked example: smoothing a rectifier

A half-wave rectifier and 2200 µF capacitor are fed from a 12.0 V rms, 60 Hz winding and supply 100 mA. 1. Peak: \(12.0\sqrt{2} - 0.7 = 16.27\) V. 2. Ripple: the capacitor supplies the load for almost a whole period, so \(\Delta V \approx I/(fC)\), giving

\Delta V \approx \frac{0.100}{(60)(2200 \times 10^{-6})} = 0.758\,\text{V}

peak-to-peak. 3. Average: about \(16.27 - 0.758/2 = 15.9\) V. 4. Check the assumption: the load is \(16.27/0.100 = 163\,\Omega\), so \(R_LC = 0.358\) s, far longer than the 16.7 ms period. 5. A full-wave rectifier recharges twice per cycle, so \(\Delta V \approx I/(2fC) = 0.379\) V, half as much.

Clippers

A clipper is a series resistor followed by a diode connected across the output. With the diode's anode at the output and its cathode to ground, the diode stays off while the output is below +0.7 V, so the wave passes unchanged; above that it conducts, holding the output near +0.7 V while the resistor takes the excess. The positive peaks are clipped. Reverse the diode, anode to ground, and the negative peaks clip at −0.7 V instead. Two diodes in inverse parallel clip both peaks at about ±0.7 V. The resistor is essential: it limits the diode current. Driven hard, a clipper squares up a sine wave.

Biased clippers and protection

To clip at another level, put a dc reference in series with the diode. A diode whose anode is at the output and cathode at a +V reference conducts once the output passes \(V + 0.7\) V; a reversed diode to a −V reference clips below \(-(V + 0.7)\) V. Two such branches confine a wave between two limits. The same idea protects chip inputs: many integrated circuits have diodes from each input to the positive rail and to ground, clipping spikes to about a drop beyond the rails, provided a series resistor keeps the current small. Radio transmitters use clippers to stop loud speech peaks overdriving them.

Worked example: a two-level clipper

A 10.0 V peak sine feeds a 1.0 kΩ series resistor. Across the output: D1, anode at the output and cathode to a +3.3 V source; D2, cathode at the output and anode to a −2.0 V source. 1. D1 conducts when the output passes \(3.3 + 0.7 = 4.0\) V, so positive peaks flatten at 4.0 V. 2. D2 conducts when the output falls below \(-2.0 - 0.7 = -2.7\) V. 3. The output swings between −2.7 V and +4.0 V, unchanged in between. 4. Peak D1 current: \((10.0 - 4.0)/1000 = 6.0\) mA. 5. Peak D2 current: \((10.0 - 2.7)/1000 = 7.3\) mA, small enough for any signal diode.

Clampers

A clamper, or dc restorer, shifts a wave without changing its shape: a series capacitor followed by a diode across the output. With the diode's anode at ground and cathode at the output, the first negative peak makes it conduct and charge the capacitor until the output is held at −0.7 V. From then on the capacitor acts as a \(V_p - 0.7\) volt battery in series with the source, so the wave rides up: negative peak at −0.7 V, positive peak at \(2V_p - 0.7\). Reversing the diode clamps the positive peak instead; a reference in series with the diode sets any level. Analogue television used clampers to pin sync pulses to a fixed level.

Worked example: clamp, then double

A 5.0 V peak sine drives the clamper just described. 1. The capacitor charges to \(5.0 - 0.7 = 4.3\) V. 2. Clamped output: \(v_s + 4.3\) V, swinging from −0.7 V to +9.3 V. 3. Now add a peak detector: a second diode from the clamped node, anode first, to a second capacitor across the output. 4. It charges to the clamped peak less one drop: \(9.3 - 0.7 = 8.6\) V, or \(2V_p - 1.4\). 5. Interpret: clamper plus peak detector is the half-wave voltage doubler. 6. Check: with ideal diodes the output would be exactly \(2V_p = 10\) V; two drops cost 1.4 V.

Voltage multipliers

The full-wave doubler stacks two half-wave rectifiers working on opposite half-cycles. One capacitor charges to \(V_p - 0.7\) on positive peaks, the other on negative peaks, and their series total, \(2(V_p - 0.7)\), is topped up twice per cycle, so it holds up better than the half-wave version. A tripler adds a rectifier stage to a doubler, and a quadrupler stacks two doublers, for about \(3V_p\) and \(4V_p\) at light load. Some power supplies once switched their bridge into a doubler on 120 V mains, so 120 V and 240 V inputs gave the same dc bus, near the 340 V peak of 240 V.

Cockcroft-Walton ladders and practical limits

Cascading half-wave doublers gives a ladder multiplier, first described by Heinrich Greinacher about 1920 and used by John Cockcroft and Ernest Walton in 1932 to accelerate protons that split lithium nuclei. Each stage adds about \(2V_p\) with no load, so the transformer never sees the full output voltage. Under load every capacitor sags and the shortfall compounds, so each added stage contributes less. Multipliers therefore suit high voltage at low current: photomultiplier tubes, ionisers and X-ray supplies. Mains-driven multipliers are hazardous, and electrolytic capacitors fail violently if their polarity is reversed.

Common mistakes to avoid

First, forgetting the drop: a peak detector holds \(V_p - 0.7\), not \(V_p\). Second, confusing clippers and clampers; a clipper removes part of the wave, a clamper shifts all of it. Third, leaving out a clipper's series resistor, which leaves nothing to limit diode current. Fourth, using the rms value where the peak belongs. Fifth, using the half-wave ripple formula for a full-wave rectifier, which recharges twice per cycle. Sixth, expecting an n-stage multiplier to give its full no-load multiple under heavy load.

Key takeaways

A peak detector, a diode charging a capacitor, holds V_p − 0.7 and is a filtered half-wave rectifier; with load current I, ripple ≈ I/(fC), or I/(2fC) for full-wave. A clipper, a series resistor and a shunt diode, limits the output to about ±0.7 V, or V + 0.7 with a reference. A clamper, a series capacitor and a shunt diode, shifts the wave so one peak sits near 0 V or a reference. A clamper plus a peak detector is the half-wave doubler, 2V_p − 1.4; full-wave doublers, triplers and Cockcroft-Walton ladders extend the idea, but sag under load.

Flashcards

Flashcard

Peak detector

A diode charging a capacitor to V_p − 0.7 and holding it

A half-wave rectifier with a filter capacitor.

Test your understanding

Question 1 of 5

A full-wave rectifier with a 4700 µF filter capacitor supplies 0.50 A from 60 Hz mains. About what is the peak-to-peak ripple?

Question 2 of 5

A clipper has a series resistor and, across the output, a silicon diode with its anode at the output and its cathode to a +5.0 V source. At what level are the positive peaks clipped?

Question 3 of 5

A 6.0 V peak sine drives a clamper whose silicon diode has its anode at ground and cathode at the output. What range does the output cover?

Question 4 of 5

A half-wave voltage doubler with silicon diodes is fed from a 10.0 V rms source. About what is its light-load output?

Question 5 of 5

Which circuit moves a whole waveform up or down without changing its shape?

← Previous topicNext topic →