Electrical Engineering › Section I · Sinusoidal waveforms and phasors › Topic I.6
Frequency response, average power, and power factor
Turn up the frequency and an inductor fights the current harder while a capacitor lets it through more easily. Look at the power instead, and only the resistance actually consumes any. These two ideas explain filters, motors and why utilities charge large customers for a poor power factor.
Reactance depends on frequency
The topic "Response of R, L, and C to sinusoids" gave the reactances \(X_L = 2\pi f L\) and \(X_C = 1/(2\pi f C)\). Both contain the frequency, so the same component behaves very differently at 60 Hz and at 10 kHz. A 22 mH inductor has a reactance of only 8.29 Ω at 60 Hz but 1.38 kΩ at 10 kHz. A 0.1 µF capacitor goes the other way: 26.5 kΩ at 60 Hz, but only 159 Ω at 10 kHz. How each element's opposition changes with frequency is called its frequency response, and it is the reason circuits can separate one frequency from another.
The three elements against frequency
An ideal resistor's value does not depend on frequency at all: a graph of \(R\) against \(f\) is a horizontal line. The inductive reactance rises in direct proportion to frequency, a straight line through the origin with slope \(2\pi L\). Double the frequency and \(X_L\) doubles. The capacitive reactance falls in inverse proportion to frequency, a curve like a hyperbola: double the frequency and \(X_C\) halves. At \(f = 0\), which is dc, \(X_L = 0\) and \(X_C\) is infinite. That matches what you already know: in dc steady state an inductor is a short circuit and a capacitor an open circuit.
Low and high frequency limits
At very high frequencies the picture reverses. An inductor's reactance grows so large that it behaves almost like an open circuit, and a capacitor's reactance shrinks until it is almost a short circuit. So an inductor passes low frequencies and blocks high ones, while a capacitor blocks low frequencies, including dc, and passes high ones. A coupling capacitor between two amplifier stages uses exactly this: it blocks the dc bias of one stage but passes the audio signal. The topic "R-C low-pass and high-pass filters" builds whole filters on these limits.
Worked example: frequencies for given reactances
Find the frequency at which a 22 mH inductor has a reactance of 1 kΩ, and where a 0.1 µF capacitor does. 1. Inductor: rearrange \(X_L = 2\pi f L\) to \(f = X_L/(2\pi L)\). 2. Substitute: \(f = 1000/(2\pi \times 0.022)\), which is 7.23 kHz. 3. Capacitor: rearrange \(X_C = 1/(2\pi f C)\) to \(f = 1/(2\pi C X_C)\). 4. Substitute:
5. Their reactances are equal where \(2\pi f L = 1/(2\pi f C)\), at \(f = 1/(2\pi\sqrt{LC}) = 3.39\,\text{kHz}\). That frequency returns in "Series resonance and the quality factor".
Real components at high frequency
Real parts are not ideal. A resistor's leads and body add a little inductance and capacitance, so at radio frequencies its impedance drifts away from \(R\). A capacitor's leads and plates add a small series inductance; above a certain frequency, its self-resonant frequency, it behaves more like an inductor than a capacitor. An inductor's turns sit close together, which adds capacitance between them, and above its own self-resonant frequency it behaves like a capacitor. Datasheets state these limits, and they are why radio circuits use short leads and surface-mount parts.
Average power
The instantaneous power into an element is \(p = vi\). With \(v = V_m \sin(\omega t + \theta_v)\) and \(i = I_m \sin(\omega t + \theta_i)\), a product-to-sum identity gives a constant term plus a term at twice the frequency:
where \(\theta = \theta_v - \theta_i\). The double-frequency term averages to zero, leaving the average, or real, power:
with \(V\) and \(I\) rms values. Average power is measured in watts.
Power in R, L and C
For a resistor, \(\theta = 0\) and \(\cos\theta = 1\), so \(P = VI = I^2R = V^2/R\), exactly as with dc when rms values are used. For an ideal inductor, \(\theta = 90^\circ\), and for an ideal capacitor, \(\theta = -90^\circ\); in both cases \(\cos\theta = 0\) and \(P = 0\). Power still flows, but it flows in for a quarter cycle while energy is stored in the magnetic or electric field, and back out the next quarter as the field collapses. The net energy over a cycle is zero. The topic "Resistive, inductive, and capacitive power" names and measures this exchanged power.
Power factor
The factor \(\cos\theta\) is the power factor, \(F_p\). It runs from 0 for a purely reactive load to 1 for a purely resistive one:
The angle \(\theta\) is the phase difference between the voltage and the current. If the current lags the voltage, as in an inductive load such as a motor, the power factor is called lagging. If the current leads, as in a capacitive load, it is leading. The cosine is the same for \(+\theta\) and \(-\theta\), so the word "lagging" or "leading" carries information the number alone cannot.
Worked example: power from two sinusoids
A load has \(v = 170 \sin(377t + \pi/6)\,\text{V}\) and \(i = 5 \sin(377t - \pi/12)\,\text{A}\). 1. Phase difference: \(\theta = \pi/6 + \pi/12 = \pi/4\), or 45°. 2. Average power: \(P = (170 \times 5/2)\cos 45^\circ\), which is \(425 \times 0.707 = 301\,\text{W}\). 3. Power factor: \(F_p = \cos 45^\circ = 0.707\). 4. The current lags the voltage, so the power factor is 0.707 lagging and the load is inductive. 5. Check with rms values: \(V = 120\,\text{V}\), \(I = 3.54\,\text{A}\), and \(120 \times 3.54 \times 0.707 = 301\,\text{W}\) again.
Worked example: a motor's power factor
A small motor on 120 V rms draws 8.0 A rms, and a wattmeter shows it absorbs 768 W. 1. The product \(VI = 120 \times 8.0 = 960\), the value the power would have at unity power factor. 2. Power factor: \(F_p = P/(VI) = 768/960 = 0.80\). 3. Phase angle: \(\theta = \cos^{-1} 0.80 = 36.9^\circ\). 4. A motor is inductive, so the current lags and the power factor is 0.80 lagging. 5. Meaning: the supply must carry 8.0 A, although a resistive load taking the same 768 W would need only 6.4 A. That extra current is why utilities care about power factor.
Common mistakes to avoid
First, assuming a capacitor or inductor behaves the same at every frequency. Second, multiplying rms voltage and current and calling the product the average power without the factor \(\cos\theta\). Third, using peak values in \(VI\cos\theta\); with peaks you need \(V_m I_m/2\). Fourth, taking \(\theta\) as the phase of the voltage alone instead of the difference between voltage and current. Fifth, quoting a power factor without saying whether it is leading or lagging.
Key takeaways
R is independent of frequency; X_L = 2πfL rises in proportion to f; X_C = 1/(2πfC) falls inversely. At dc an inductor is a short and a capacitor an open; at high frequency the reverse. Real components have self-resonant limits. Average power is P = VI cos θ with rms values, or V_mI_m cos θ / 2 with peaks, where θ = θ_v − θ_i. A resistor takes P = I²R; ideal L and C take zero average power. Power factor F_p = cos θ = P/(VI) is lagging for inductive loads, where current lags, and leading for capacitive ones.
Flashcards
Flashcard
Constant: R does not depend on f
Test your understanding
Question 1 of 5
The frequency of the source across a capacitor is tripled. What happens to its reactance?
Question 2 of 5
A load has v = 100 sin(ωt + π/6) V and i = 4 sin(ωt − π/6) A. What average power does it absorb?
Question 3 of 5
At what frequency does a 47 mH inductor have a reactance of 500 Ω?
Question 4 of 5
A 230 V rms supply delivers 5.0 A rms to a load whose current lags by 53.1°. Which statement is correct?
Question 5 of 5
What average power does an ideal 0.5 H inductor absorb from a 120 V rms, 60 Hz supply?
