Electrical Engineering › Section I · Sinusoidal waveforms and phasors › Topic I.5

Response of R, L, and C to sinusoids

Drive a resistor, an inductor or a capacitor with a sinusoid and the result is always a sinusoid of the same frequency, but each element sets its own ratio of voltage to current and its own phase shift. Those two facts, worked out here from the derivative, are the foundation of all ac circuit analysis.

Three elements, three behaviours

In dc steady state an inductor is simply a short circuit and a capacitor an open circuit. With ac they behave quite differently, because their voltages and currents are linked by rates of change. An inductor's voltage depends on how fast its current changes, and a capacitor's current depends on how fast its voltage changes. A sinusoid is always changing, so both elements respond all the time. To find that response you need one result from calculus: the derivative of a sinusoid. Throughout, each element uses the passive sign convention: current enters the terminal marked +.

The derivative of a sinusoid

The derivative of a sine is a cosine scaled by the angular frequency:

\frac{d}{dt}\left[\sin \omega t\right] = \omega \cos \omega t = \omega \sin\left(\omega t + \frac{\pi}{2}\right)

Two features matter. The derivative is again a sinusoid of the same frequency, shifted a quarter cycle earlier: it peaks where the original crosses zero, because that is where the sine is steepest, and it is zero at the original's peaks. And its size is multiplied by \(\omega\), so a faster sinusoid of the same peak value changes more quickly. Both features reappear in the inductor and the capacitor.

The resistor

For a resistor, Ohm's law holds at every instant: \(i = v/R\). If \(v = V_m \sin \omega t\), then

i = \frac{V_m}{R} \sin \omega t = I_m \sin \omega t

The current has the same frequency and the same phase as the voltage: they are in phase, peaking and crossing zero together. The peak values obey \(I_m = V_m/R\), and since rms values are peaks divided by \(\sqrt{2}\), the rms values obey the same law, \(I = V/R\). An ideal resistor's behaviour does not depend on frequency at all. For example, \(v = 24 \sin(377t)\,\text{V}\) across 1.2 kΩ gives \(i = 20 \sin(377t)\,\text{mA}\).

The inductor

As "Self-inductance, inductor types, and induced voltage" showed, an inductor obeys \(v_L = L\,di/dt\). If \(i = I_m \sin \omega t\), then

v_L = \omega L I_m \sin\left(\omega t + \frac{\pi}{2}\right)

The voltage leads the current by 90°. The ratio of peak voltage to peak current is \(\omega L\), called the inductive reactance:

X_L = \omega L = 2\pi f L

It is measured in ohms, so \(V_m = I_m X_L\), and \(V = I X_L\) in rms. If the current has a phase angle \(\theta\), the voltage's phase angle is \(\theta + \pi/2\).

Worked example: an inductor on 60 Hz

A 100 mH inductor carries \(i = 0.2 \sin(377t)\,\text{A}\). Find the voltage across it. 1. Reactance: \(X_L = \omega L = 377 \times 0.1 = 37.7\,\Omega\). 2. Peak voltage: \(V_m = I_m X_L\), which is \(0.2 \times 37.7 = 7.54\,\text{V}\). 3. Phase: the voltage leads the current by 90°, so add \(\pi/2\) to the current's phase angle of 0. 4. Result: \(v_L = 7.54 \sin(377t + \pi/2)\,\text{V}\). 5. Check: the rms values are 5.33 V and 0.141 A, whose ratio is again 37.7 Ω, and the voltage peaks at \(t = 0\), where the current is rising fastest.

The capacitor

As "Charging and discharging transients" showed, a capacitor obeys \(i_C = C\,dv/dt\). If \(v = V_m \sin \omega t\), then

i_C = \omega C V_m \sin\left(\omega t + \frac{\pi}{2}\right)

Now the current leads the voltage by 90°. The ratio of peak voltage to peak current is \(1/(\omega C)\), the capacitive reactance:

X_C = \frac{1}{\omega C} = \frac{1}{2\pi f C}

It too is in ohms, with \(I_m = V_m/X_C\) and \(I = V/X_C\) in rms. The voltage across a capacitor is the one that lags; if the voltage has phase angle \(\theta\), the current has \(\theta + \pi/2\).

Worked example: a capacitor at 1000 rad/s

A 4.7 µF capacitor has \(v = 10 \sin(1000t)\,\text{V}\) across it. Find its current. 1. Reactance, to three significant figures:

X_C = \frac{1}{\omega C} = \frac{1}{1000 \times 4.7 \times 10^{-6}} = 213\,\Omega

2. Peak current: \(I_m = 10/212.8 = 47.0\,\text{mA}\). 3. Phase: the current leads the voltage by 90°. 4. Result: \(i_C = 47.0 \sin(1000t + \pi/2)\,\text{mA}\). 5. Check: the direct formula \(I_m = \omega C V_m\) gives \(1000 \times 4.7\,\mu\text{F} \times 10\,\text{V}\), which is again 47.0 mA.

Reactance is not resistance

Reactance and resistance share the ohm because both give a ratio of voltage to current, but they differ in two ways. Reactance always comes with a 90° phase shift, so the peaks of voltage and current never coincide. And an ideal inductor or capacitor dissipates no energy on average: it stores energy for a quarter cycle and returns it the next, as "Frequency response, average power, and power factor" shows. A memory aid for the phases is "ELI the ICE man": in an inductor (L), the voltage E comes before the current I; in a capacitor (C), the current I comes before E.

Worked example: naming the element

An unknown element has \(v = 100 \sin(500t + \pi/3)\,\text{V}\) and \(i = 2 \sin(500t - \pi/6)\,\text{A}\). 1. Phase difference: \(\theta_v - \theta_i = \pi/3 + \pi/6 = \pi/2\), so the voltage leads by 90°. 2. Voltage leading by 90° means an inductor; in phase would mean a resistor, and current leading by 90° a capacitor. 3. Reactance: \(X_L = V_m/I_m = 100/2 = 50\,\Omega\). 4. Inductance: \(L = X_L/\omega = 50/500 = 0.1\,\text{H}\). 5. Check: \(\omega L I_m = 500 \times 0.1 \times 2 = 100\,\text{V}\), the given peak.

Common mistakes to avoid

First, writing \(X_L = fL\) or \(X_C = 1/(fC)\), dropping the \(2\pi\) when frequency is given in hertz. Second, getting the lead backwards: voltage leads in an inductor, current leads in a capacitor. Third, adding resistance and reactance as plain numbers, which ignores the 90° shift; "Impedance, phasor diagrams, and series ac circuits" shows how they combine. Fourth, dividing a peak voltage by a reactance and calling the answer an rms current; keep peak with peak and rms with rms. Fifth, forgetting to add the 90° to an existing phase angle.

Key takeaways

The derivative of sin ωt is ω sin(ωt + π/2): same frequency, a quarter cycle earlier, scaled by ω. A resistor keeps voltage and current in phase with V_m = I_m R. An inductor's voltage leads its current by 90°, with reactance X_L = ωL = 2πfL. A capacitor's current leads its voltage by 90°, with reactance X_C = 1/(ωC) = 1/(2πfC). Reactance is a ratio of peak, or of rms, values measured in ohms, but it stores and returns energy rather than dissipating it. ELI the ICE man recalls the phases, and the phase difference of a v and i pair identifies the element.

Flashcards

Flashcard

d/dt sin ωt

ω cos ωt = ω sin(ωt + π/2)

Same frequency, a quarter cycle earlier, times ω.

Test your understanding

Question 1 of 5

What is the reactance of a 50 mH inductor at an angular frequency of 400 rad/s?

Question 2 of 5

A 10 µF capacitor has v = 20 sin(500t) V across it. What is its current?

Question 3 of 5

An element has v = 30 sin(ωt − π/4) V and i = 5 sin(ωt + π/4) A. What is it?

Question 4 of 5

In an inductor carrying i = I_m sin ωt, when is the voltage across it at its positive peak?

Question 5 of 5

A 120 V rms, 60 Hz source is connected across a 26.5 µF capacitor. What is the rms current?

← Previous topicNext topic →