Electrical Engineering › Section Y · Time-varying fields, Maxwell's equations, and plane waves › Topic Y.2

Guided and unguided waves

An electromagnetic wave either follows a structure built to carry it, such as a cable or an optical fibre, or spreads freely into space from an antenna. Knowing which kind you have, and when an ordinary wire starts behaving like either, is basic to radio, fast digital design and electromagnetic compatibility.

Two families of waves

Every electromagnetic wave in engineering falls into one of two families. A guided wave is held to a path by a structure: it follows a coaxial cable round corners, travels along a circuit-board trace, or stays inside an optical fibre for kilometres. An unguided wave is released into space and travels outward with nothing steering it, until something scatters it, reflects it or absorbs it. Antennas are the devices that convert one family into the other. The previous topic's wave ideas, wavelength, wavenumber and phase velocity, apply to both.

Unguided waves

An antenna fed by a transmitter launches unguided waves on purpose. Many other things launch them by accident: a switching power supply, a motor's brushes, or a long digital trace. These unintentional radiators obey the same physics. Once launched, an unguided wave spreads its power over an ever larger area. For a source radiating power P equally in all directions, the power per square metre at distance r is

S = \frac{P}{4\pi r^2}

so doubling the distance quarters the power density. Buildings, terrain and rain then scatter or absorb part of what remains.

Guided waves

Three structures carry most guided waves. Transmission lines have two or more conductors: coaxial cable, twisted pairs and circuit-board traces over a ground plane. Waveguides are hollow metal pipes used at microwave frequencies; each passes only frequencies above a cutoff set by its width. Optical fibres are thin strands of glass that trap infrared light in their core by total internal reflection. Because the structure confines the wave, little power is lost to spreading, and losses come mainly from the materials. A guided wave in a cable travels slower than c; the ratio of its speed to c is the cable's velocity factor, often about 0.66 for solid-polyethylene coax.

When a wire becomes a transmission line

Two wires carrying a signal always form a transmission line; the question is whether that matters. When the line is much shorter than a wavelength, the voltage is practically the same along it and lumped circuit analysis works. Once the line approaches a tenth of a wavelength or more, the voltage and current vary along its length, and the line's characteristic impedance, set by its geometry and insulation, starts to matter. Common values are 50 Ω for radio-frequency coax, 75 Ω for television and video coax, and about 100 Ω for Ethernet twisted pairs. A load equal to that impedance absorbs the wave; any other load reflects part of it back.

Worked example: is the cable electrically long?

A 2.0 m coaxial cable has a velocity factor of 0.66. Is it electrically long at 1 kHz, 10 MHz and 100 MHz? 1. Wave speed in the cable: \(v = 0.66 \times 3.00 \times 10^{8} = 1.98 \times 10^{8}\,\text{m/s}\). 2. At 1 kHz, \(\lambda = v/f = 198\,\text{km}\), so the cable is about \(10^{-5}\) wavelengths long: a plain pair of wires. 3. At 10 MHz, \(\lambda = 19.8\,\text{m}\), and the cable is 0.10 wavelengths, right at the rule-of-thumb limit. 4. At 100 MHz, \(\lambda = 1.98\,\text{m}\), and the cable is about one wavelength long: it must be treated as a transmission line and terminated correctly. Check: each tenfold rise in frequency makes the cable ten times longer in wavelengths.

Antennas: the bridge

An antenna is a structure that turns a guided wave into an unguided one, or the reverse. Charges that accelerate radiate, so the alternating current a transmitter drives into a conductor launches waves. By reciprocity, the same antenna receives as well as it transmits in each direction. Two basic designs set the scale: the half-wave dipole, two rods totalling about half a wavelength and fed at the centre, and the quarter-wave monopole, a single rod above a conducting ground plane that acts as the dipole's missing half. Real antennas favour some directions: directivity, and gain (directivity reduced by the antenna's own losses), say how strongly one concentrates power compared with an equal spread in all directions. Because antenna size scales with wavelength, higher frequencies allow smaller antennas, which is one reason phones use frequencies near a gigahertz and above.

Worked example: quarter-wave antennas

Size quarter-wave monopoles for 915 MHz, a licence-free band in the Americas, and for 2.45 GHz. 1. At 915 MHz: \(\lambda = 3.00 \times 10^{8}/915 \times 10^{6} = 0.328\,\text{m}\), so \(\lambda/4 = 8.20\,\text{cm}\). 2. At 2.45 GHz: \(\lambda = 0.122\,\text{m}\), so \(\lambda/4 = 3.06\,\text{cm}\), small enough to print as a trace on a board. 3. In practice the element is trimmed a few percent shorter than the free-space value, because fields fringing at the tip make it act slightly longer than it is. Check: the frequency ratio is \(2450/915 = 2.68\), and the length ratio is \(8.20/3.06 = 2.68\), as an inverse proportion requires.

Signal integrity

Fast digital signals are guided waves whether or not the designer intends it. What matters is the edge, not the clock rate: a rough rule says an edge with rise time \(t_r\) contains significant energy up to about \(0.35/t_r\), so a 1 ns edge reaches about 350 MHz. In FR-4 circuit board, signals travel at roughly half of c, so that edge occupies only about 15 cm of trace. Traces of comparable length need a controlled characteristic impedance and proper termination, or reflections ring on the line. Unbroken ground planes and short return paths keep each signal's current loop small, so the trace neither radiates much nor picks up noise.

Electromagnetic compatibility

EMC asks two questions of any product: how much does it emit, and how well does it tolerate what others emit? Emissions travel as guided waves along power and data cables and as unguided waves from anything that acts as an accidental antenna, such as a cable or a slot in a metal case whose length approaches a half-wavelength. Immunity is the ability to keep working when such waves arrive. Regulators set limits: the FCC in the United States and the CE-marking rules in the European Union, for example. Testing for compliance is a normal part of bringing electronics to market, and failing late is expensive.

Common mistakes to avoid

First, assuming a wire is just a wire at every frequency; once it nears a tenth of a wavelength it is a transmission line. Second, using the free-space wavelength inside a cable; multiply it by the velocity factor, since the wave is slower there. Third, judging a digital signal by its clock rate instead of its edge rate. Fourth, thinking only antennas radiate; cables, traces and slots radiate too. Fifth, expecting an unguided wave's power density to fall in proportion to distance; it falls with the square of distance.

Key takeaways

Guided waves follow transmission lines, waveguides and optical fibres; unguided waves spread from antennas and unintentional radiators, with power density falling as 1/r² from a point source. A line longer than about a tenth of a wavelength needs transmission-line treatment and a matched load of its characteristic impedance, commonly 50 Ω or 75 Ω for coax. Antennas convert between the two kinds; dipoles are about λ/2 and monopoles about λ/4. Fast edges, not clock rates, decide signal-integrity and EMC problems.

Flashcards

Flashcard

Guided wave

A wave held to a path by a structure

Coax, board traces, waveguides, optical fibre.

Test your understanding

Question 1 of 5

Which of these carries a guided wave?

Question 2 of 5

A 3.0 m cable with velocity factor 0.66 carries a 50 MHz signal. About how many wavelengths long is it?

Question 3 of 5

What is the length of a quarter-wave monopole for 300 MHz, before any trimming?

Question 4 of 5

A source radiates equally in all directions. At 100 m its power density is 80 µW/m². What is it at 400 m?

Question 5 of 5

A board's clock runs at only 10 MHz, but its logic edges rise in 0.5 ns. What decides whether its traces need transmission-line care?

← Previous topicNext topic →