Electrical Engineering › Section Y · Time-varying fields, Maxwell's equations, and plane waves › Topic Y.3

Time-varying fields, electromagnetic induction, and Faraday's law

When fields change in time, electricity and magnetism stop being separate subjects. This topic restates Faraday's law as a statement about fields, with a sign convention that works for any loop in any field, and uses it to find the voltage induced in a stationary loop.

From statics to dynamics

Electrostatics and magnetostatics treat the electric and magnetic fields as independent: charges make one, steady currents the other. Once the fields vary in time, the laws gain extra terms, each a time derivative of a field, and those terms couple the two fields together. A changing magnetic field produces an electric field, and, as a later topic shows, a changing electric field produces a magnetic field. The coupling has a striking consequence: fields can keep going after the charges and currents that made them have been switched off, each sustaining the other. Such a self-sustaining field is a wave, like a signal on a cable or the radiation leaving an antenna.

Induction makes a voltage

"Faraday's and Lenz's laws" showed that changing flux through a coil induces a voltage. It is worth being precise about what is induced. Replace the load on a coil with a high-resistance voltmeter and move a magnet nearby: the meter shows a changing voltage even though almost no current flows. So the voltage is the primary effect, and any current is simply the response of whatever closes the circuit, given by Ohm's law, \(I = V/R\). Lenz's law then describes the direction of that current: its own magnetic field opposes the change in the applied field. Lenz's law is a quick way to check signs, and energy conservation demands it.

Faraday's law in field form

Take a loop of wire with a small gap, and call the voltage across the gap \(v_T\), with chosen + and − terminals. For N closely wound turns, Faraday's law is

v_T = -N\frac{d\Phi}{dt}, \qquad \Phi = \int_S \mathbf{B} \cdot d\mathbf{A}

The flux \(\Phi\) is the flux density integrated over any surface S whose edge is the loop. Here \(d\mathbf{A}\) is a small patch of S, a vector whose length is the patch's area and whose direction, the unit normal \(\hat{\mathbf{n}}\), is perpendicular to it. The induced voltage is often called the emf, short for electromotive force, although it is a voltage, not a force.

The minus sign and the right-hand rule

A surface has two possible normals, and the choice must be tied to the polarity of \(v_T\). Curl the fingers of your right hand along the wire from the − terminal round to the + terminal; your thumb then points along \(\hat{\mathbf{n}}\). With that rule fixed, the minus sign carries Lenz's law: a flux rising along \(\hat{\mathbf{n}}\) makes \(v_T\) negative. The circuits topic wrote \(e = N\,d\Phi/dt\) and set the polarity separately with Lenz's law. Both give the same size and the same physical polarity; the field form simply builds the polarity into a rule that works for loops of any shape and any field direction.

Transformer emf and motional emf

Since \(\Phi\) is a flux density integrated over a surface, it can change in two ways. If \(\mathbf{B}\) itself changes with time, for example because the current in a nearby coil changes, the result is called transformer emf; it is how transformers work. If the loop moves, rotates or changes shape in a steady field, the surface changes and the result is motional emf; it is how generators work. The two can occur together, and Faraday's law treats them identically. Nor does the law need a wire: it gives the induced voltage round any closed path in space, conducting or not.

A motionless loop in a uniform field

Let a flat loop of area A sit still in a field that is the same everywhere but varies in time, \(\mathbf{B} = \hat{\mathbf{b}}B(t)\), where \(\hat{\mathbf{b}}\) is a fixed unit vector. Then B comes outside the integral and

v_T = -N(\hat{\mathbf{b}} \cdot \hat{\mathbf{n}})A\,\frac{dB}{dt}

The product \((\hat{\mathbf{b}} \cdot \hat{\mathbf{n}})A\) is the projected area, the loop's area as seen along the field. Three things follow. The loop's shape does not matter, only its area. The voltage is largest when the field is perpendicular to the loop's plane and zero when it lies in that plane. And a constant B induces nothing, however strong.

Worked example: a ramping, tilted field

A rectangular single-turn loop, 10 cm by 20 cm, lies in the xy-plane with its terminals chosen so that \(\hat{\mathbf{n}} = +\hat{\mathbf{z}}\). A 22 Ω resistor closes the gap. A uniform field at 30° to the z-axis rises steadily from 0 to 0.60 T in 0.25 s. 1. Area: \(A = 0.0200\,\text{m}^2\), and \(\hat{\mathbf{b}} \cdot \hat{\mathbf{n}} = \cos 30^\circ = 0.866\). 2. Rate: \(dB/dt = 0.60/0.25 = 2.40\,\text{T/s}\). 3. Voltage:

v_T = -0.866 \times 0.0200 \times 2.40 = -41.6\,\text{mV}

4. Current: \(I = v_T/R = -1.89\,\text{mA}\), taking the reference current as leaving the + terminal through the resistor, as for a source; the negative sign means it actually flows the other way. 5. Lenz check: that current circulates so that its own flux points towards \(-\hat{\mathbf{z}}\), opposing the rising flux, as it must.

Worked example: a sinusoidal field

A 50-turn circular coil of radius 4.0 cm faces a uniform 60 Hz field \(B(t) = 2.0\sin(377t)\,\text{mT}\), with \(\hat{\mathbf{b}} = \hat{\mathbf{n}}\). Find the induced voltage. 1. Area: \(A = \pi (0.040)^2 = 5.03 \times 10^{-3}\,\text{m}^2\). 2. Derivative: \(dB/dt = 377 \times 2.0\cos(377t)\,\text{mT/s}\). 3. Voltage:

v_T = -50 \times 5.03 \times 10^{-3} \times 0.754\cos(377t)

which is \(-0.190\cos(377t)\,\text{V}\), or \(0.190\sin(377t - \pi/2)\,\text{V}\): a peak of 190 mV, 134 mV rms. 4. Observe the timing: the voltage lags the field by 90°, and it peaks at the instants when B passes through zero, because that is when B changes fastest. Check: doubling the frequency would double the voltage.

Common mistakes to avoid

First, saying induction creates current; it creates voltage, and current follows only if the circuit is closed. Second, choosing \(\hat{\mathbf{n}}\) without tying it to the terminal polarity, which makes the sign of \(v_T\) meaningless. Third, using the full area when the field is tilted; use the projected area, \((\hat{\mathbf{b}} \cdot \hat{\mathbf{n}})A\). Fourth, expecting the voltage to peak when B peaks; it peaks when B changes fastest. Fifth, thinking Faraday's law needs a conductor; it applies round any closed path.

Key takeaways

Time-varying fields couple electric and magnetic fields, which allows waves to exist without sources. Induction produces a voltage; current is Ohm's-law response. Faraday's law in field form is \(v_T = -N\,d\Phi/dt\) with \(\Phi = \int_S \mathbf{B} \cdot d\mathbf{A}\); the normal follows the right-hand rule from the − terminal round to the +, and the minus sign is Lenz's law. Changing B gives transformer emf; a moving loop gives motional emf. For a still loop in a uniform field, \(v_T = -N(\hat{\mathbf{b}} \cdot \hat{\mathbf{n}})A\,dB/dt\), so only the projected area and the rate of change matter.

Flashcards

Flashcard

Time-varying fields

Fields whose laws gain time-derivative terms that couple E and B

The coupling allows waves.

Test your understanding

Question 1 of 5

A single-turn loop of area 0.050 m² faces a uniform field squarely. The field rises steadily from 0.20 T to 0.80 T in 0.15 s. What is the size of the induced voltage?

Question 2 of 5

The same uniform, changing field is applied to a loop turned so that the field lines lie in the plane of the loop. What is induced?

Question 3 of 5

A coil sits in a uniform field B = B_m sin ωt applied squarely. When is the induced voltage largest in size?

Question 4 of 5

A loop is closed only by a very high-resistance voltmeter, and the flux through it changes. Which statement is correct?

Question 5 of 5

A 100-turn coil of area 0.010 m² faces a uniform 50 Hz field with peak 0.050 T. What is the peak induced voltage?

← Previous topicNext topic →