Electrical Engineering › Section Y · Time-varying fields, Maxwell's equations, and plane waves › Topic Y.6
Maxwell's equations in differential phasor form
Four equations describe every classical electric and magnetic effect, from a capacitor's charge to a radio wave. Written with phasors, their time derivatives become multiplication by jω, which is the same simplification that made ac circuit analysis possible.
Four laws, one system
James Clerk Maxwell drew the laws of Gauss, Faraday and Ampère into one framework, added the displacement current, and published the full theory in 1865. In the 1880s Oliver Heaviside recast it as the four compact vector equations used today. Two have already appeared in this section: the Maxwell-Faraday equation and the Ampère-Maxwell law. The other two come from statics and survive unchanged when fields vary. Gauss's law, met in "The electric field", says electric flux out of a closed surface equals the charge inside. Gauss's law for magnetism says the magnetic flux out of any closed surface is zero.
The integral form
In integral form, with S a closed surface in the first and third lines and an open surface bounded by the path C in the other two:
The minus sign in the second line, Faraday's law, is Lenz's law, and the normal to each open surface follows the right-hand rule from the direction of C. These forms suit problems with symmetry, such as the capacitor of the previous topic.
The differential form
Shrinking each surface or path to a point gives the point form. Besides the curl, this needs the divergence, \(\nabla \cdot \mathbf{D}\), the net outflow of a field per unit volume at a point; the divergence theorem links it to flux through a closed surface. With \(\rho_v\) the charge density in C/m³:
In words: charge is where electric flux starts and ends; a changing B makes E swirl; magnetic field lines never start or end, since there are no magnetic monopoles; and currents and changing E make H swirl.
The material relations
The four equations involve four fields, so the materials must link them. In a linear, uniform material that behaves the same in every direction,
where \(\varepsilon = \varepsilon_r\varepsilon_0\) is the permittivity, \(\mu = \mu_r\mu_0\) the permeability, and \(\sigma\) the conductivity in S/m. The last relation is Ohm's law at a point. With these constitutive relations the equations can be written in E and H alone, which is the usual engineering choice.
Phasors for fields
Most engineering fields vary sinusoidally at a single frequency, so phasors apply just as in circuits. This section keeps the course convention: sine reference and rms magnitude. A field phasor carries a tilde, and it can still depend on position. For each component,
where the imaginary part is the vertical projection of the rotating arrow, the sine of "Phasors". So a component \(\tilde{E}_x = 5\angle 30^\circ\,\text{V/m}\) means \(E_x(t) = 5\sqrt{2}\sin(\omega t + \pi/6)\). Many electromagnetics books, Ellingson's among them, use the cosine and peak values instead; their phasor relations look the same, but power formulas then carry an extra factor of 1/2.
Time derivatives become jω
Substitute phasors into the Maxwell-Faraday equation. The curl acts on position only and taking the imaginary part is a linear step, so both can be swapped freely, and the time derivative falls on \(e^{j\omega t}\) alone, giving \(j\omega\). Equal expressions for every t mean equal phasors, so \(\nabla \times \tilde{\mathbf{E}} = -j\omega\tilde{\mathbf{B}}\). The other three follow the same way:
Only spatial derivatives remain, which makes wave problems solvable by algebra plus ordinary differential equations.
Worked example: from phasor to field
At a point, a 100 MHz field has \(\tilde{\mathbf{E}} = \hat{\mathbf{x}}\,(5.0\angle 30^\circ)\,\text{V/m}\), rms, in polar form. Write \(\mathbf{E}(t)\) and the phasor of \(\partial\mathbf{E}/\partial t\). 1. Peak: \(5.0\sqrt{2} = 7.07\,\text{V/m}\); \(\omega = 2\pi \times 10^{8} = 6.28 \times 10^{8}\,\text{rad/s}\); 30° is \(\pi/6\). 2. So
3. Derivative phasor: multiply by \(j\omega = \omega\angle 90^\circ\), giving \(\hat{\mathbf{x}}\,(3.14 \times 10^{9}\angle 120^\circ)\,\text{V/(m s)}\). 4. Check directly: the derivative of \(7.07\sin(\omega t + \pi/6)\) is \(7.07\omega\cos(\omega t + \pi/6)\), a sine advanced by a further 90°, with rms value \(5.0\omega\).
Worked example: current in seawater
Seawater has \(\sigma \approx 4\,\text{S/m}\) and \(\varepsilon_r \approx 81\). A 10 MHz field \(\tilde{E} = 1.0\angle 0^\circ\,\text{mV/m}\) acts in it. Find the total current density on the right of the phasor Ampère-Maxwell law, \(\tilde{\mathbf{J}} + j\omega\tilde{\mathbf{D}} = (\sigma + j\omega\varepsilon)\tilde{\mathbf{E}}\). 1. Conduction: \(\sigma\tilde{E} = 4.0\,\text{mA/m}^2\) at 0°. 2. Displacement, at 90°:
3. Total, rectangular form: \(4.000 + j0.0451\,\text{mA/m}^2\), or \(4.00\angle 0.65^\circ\) in polar form. 4. Conduction dominates by \(\sigma/(\omega\varepsilon) = 89\); the two are equal near \(f = \sigma/(2\pi\varepsilon)\), about 890 MHz if σ and εᵣ stayed constant that high.
Common mistakes to avoid
First, mixing conventions: a cosine, peak-value phasor from another book differs from this course's sine, rms phasor, so convert before reusing results. Second, replacing \(\partial/\partial t\) with \(j\omega\) but forgetting the minus sign in \(-j\omega\tilde{\mathbf{B}}\). Third, thinking a phasor field cannot vary with position; only the time dependence is removed. Fourth, writing \(\nabla \cdot \mathbf{B} = \rho_v\); magnetic flux has no sources. Fifth, adding conduction and displacement current densities as plain numbers instead of as phasors 90° apart.
Key takeaways
Maxwell's equations are Gauss's law, the Maxwell-Faraday equation with its minus sign, Gauss's law for magnetism and the Ampère-Maxwell law, in integral and point forms. Materials link the fields by \(\mathbf{D} = \varepsilon\mathbf{E}\), \(\mathbf{B} = \mu\mathbf{H}\) and \(\mathbf{J} = \sigma\mathbf{E}\). With phasors, sine reference and rms in this course, every \(\partial/\partial t\) becomes \(j\omega\): \(\nabla \times \tilde{\mathbf{E}} = -j\omega\tilde{\mathbf{B}}\) and \(\nabla \times \tilde{\mathbf{H}} = \tilde{\mathbf{J}} + j\omega\tilde{\mathbf{D}}\). In a conductor the total current density is \((\sigma + j\omega\varepsilon)\tilde{\mathbf{E}}\).
Flashcards
Flashcard
Maxwell's theory of 1865; Heaviside's vector form in the 1880s
Test your understanding
Question 1 of 5
A field component has rms phasor 2.0∠−45° V/m at angular frequency ω, in this course's convention. What is it in the time domain?
Question 2 of 5
What does the time derivative ∂B/∂t become in phasor form?
Question 3 of 5
Which of Maxwell's equations states that magnetic field lines never begin or end?
Question 4 of 5
A material has σ = 0.010 S/m and εᵣ = 10. At 100 MHz, roughly what is the ratio of conduction to displacement current density?
Question 5 of 5
A textbook gives a field phasor as 10∠0° V/m using a cosine reference and peak values. What is the same field in this course's convention?
