Electrical Engineering › Section W · Signal conversion and data transmission › Topic W.4
Transmission modes, modulation, and multiplexing
Sending data is more than switching a wire on and off. Engineers choose how bits are timed and coded, how they ride on carrier waves, how analog signals become pulses, and how many conversations share one channel.
Serial or parallel, synchronous or asynchronous
Parallel transmission sends several bits at once on separate lines; serial transmission sends them one after another on one line or pair. Serial links need fewer wires and avoid timing skew between lines, so they dominate beyond short distances. Synchronous transmission locks sender and receiver to a shared clock, sent separately or recovered from the data. Asynchronous transmission frames each character with a start bit and stop bits, so the receiver resynchronises on every character. Simplex links go one way only, like broadcast radio; half-duplex links go both ways in turn, like a walkie-talkie; full-duplex links go both ways at once, like a phone call.
Line codes: NRZ, RZ and Manchester
A line code sets how bits become voltage levels. In non-return-to-zero (NRZ) coding the level stays high for a whole 1 and low for a whole 0, so a long run of identical bits has no transitions and the receiver can lose count. Return-to-zero (RZ) coding drops back to zero halfway through each 1. Manchester, or biphase, coding puts a transition in the middle of every bit: in the IEEE 802.3 Ethernet convention a 1 is low then high and a 0 is high then low, though some texts use the opposite. Every bit carries a clock edge and the average level is constant, but about twice the bandwidth of NRZ is needed. So 1011 becomes low-high, high-low, low-high, low-high.
Bit rate, baud and overhead
Bit rate counts bits sent per second, in b/s. The baud, or symbol rate, counts symbols per second, where a symbol is one distinct signal state, such as a voltage level or a phase. If each symbol can take one of \(M\) states, it carries \(\log_2 M\) bits, so
Bit rate and baud are equal only for two-state signalling. Not every bit sent is data: start and stop bits, synchronisation patterns, addresses and error checks are overhead. Efficiency is the fraction of transmitted bits that are useful data.
Worked example: symbols and overhead
1. A link sends 16 distinct voltage levels at 2400 baud. Each symbol carries \(\log_2 16 = 4\) bits, so the bit rate is \(2400 \times 4 = 9600\) b/s. 2. A UART, the asynchronous serial port of "Parallel buses, USB, and serial buses", sends 8 data bits per character with one start and one stop bit, a format written 8N1. Each character takes 10 bits, so efficiency is \(8 \div 10 = 80\%\). 3. At 115,200 baud, two-level signalling, that gives \(115{,}200 \div 10 = 11{,}520\) characters per second, or 92,160 data bits per second. 4. Check: 11,520 × 8 = 92,160, which is 80% of 115,200.
Digital data on a carrier: ASK, FSK, PSK
Radio links and telephone lines cannot carry raw pulses, so digital data modulates a sinusoidal carrier, \(v(t) = V_p \sin(2\pi f t + \theta)\), by changing its amplitude, frequency or phase. Amplitude-shift keying (ASK) switches the amplitude between levels; its simplest form, on-off keying, sends the carrier for a 1 and nothing for a 0. Frequency-shift keying (FSK) uses one frequency for a 1 and another for a 0, and resists amplitude noise. Phase-shift keying (PSK) shifts the phase: binary PSK uses 0° and 180°, one bit per symbol, while quadrature PSK (QPSK) uses four phases 90° apart, two bits per symbol.
Quadrature amplitude modulation
Quadrature amplitude modulation (QAM) changes amplitude and phase together. Each allowed combination is a point on a constellation diagram, plotted with the in-phase part on one axis and the quadrature part on the other. With \(M\) points each symbol carries \(\log_2 M\) bits: 16-QAM carries 4, 64-QAM 6 and 256-QAM 8. At 5 million symbols per second, 64-QAM therefore moves \(5 \times 10^6 \times 6 = 30\) Mb/s. Denser constellations put their points closer together, so noise causes more errors, and links drop to smaller constellations when the signal weakens. Cable modems, Wi-Fi and cellular networks use QAM; the newest Wi-Fi reaches 4096 points.
Pulse modulation: PAM, PWM and PPM
The reverse problem is carrying analog information on pulses. In pulse amplitude modulation (PAM), a regular train of pulses takes heights equal to samples of the analog signal. In pulse width modulation (PWM), the pulse width follows the signal, as in "Pulse waveforms, repetition rate, duty cycle, and average value"; a comparator against a sawtooth produces it. In pulse position modulation (PPM), every pulse has the same size, and its position within a fixed time slot carries the value. All three remain analog in a sense, since each pulse property can take any value in its range.
PCM and delta modulation
Pulse code modulation (PCM) makes the signal fully digital: sample it, quantise each sample to one of \(L\) levels, and send each level as an n-bit binary code, with \(2^n \ge L\). Telephone systems use PCM, and so do CDs and most digital audio files before compression. A voice channel with 1024 levels needs 10 bits per sample, and at 8000 samples per second that is 80 kb/s. Delta modulation sends one bit per sample: 1 if the signal is above the running estimate, which then steps up, and 0 if below, so it steps down. A signal changing faster than the steps can follow causes slope overload; a steady one makes the estimate hunt, called granular noise.
Multiplexing: TDM and FDM
Multiplexing lets many signals share one channel, and demultiplexing separates them at the far end, the same idea as "Multiplexers, demultiplexers, and parity" applied to links. Time-division multiplexing (TDM) gives each signal a time slot in turn; the channel must run fast enough to carry every slot plus framing bits that mark where each frame starts. Frequency-division multiplexing (FDM) gives each signal its own band of frequencies on a separate carrier, with guard bands between them, so all transmit at once. Radio and television broadcasting are FDM. Wavelength-division multiplexing in optical fibre is FDM using colours of light.
Worked example: a T1 line
The North American T1 line uses TDM to carry 24 telephone channels. Each channel is PCM speech: 8000 samples per second, 8 bits each. 1. One frame holds one sample from every channel: \(24 \times 8 = 192\) bits. 2. One framing bit is added per frame: 193 bits. 3. Frames are sent at the sampling rate, 8000 per second, so the line rate is \(193 \times 8000 = 1{,}544{,}000\) b/s, the familiar 1.544 Mb/s. 4. Voice payload: \(24 \times 64\,\text{kb/s} = 1.536\) Mb/s. 5. Check: the difference, 8000 b/s, is exactly the framing bits, one per frame.
Common mistakes to avoid
First, treating baud and bit rate as the same: they match only when each symbol carries one bit. Second, counting only data bits when finding a UART's throughput: start and stop bits take time too. Third, assuming a bigger QAM constellation is always better: it needs a cleaner signal. Fourth, choosing too few PCM bits: n bits give only \(2^n\) levels, so 100 levels need 7 bits. Fifth, mixing up TDM and FDM: TDM shares time, FDM shares frequency. Sixth, calling a walkie-talkie full-duplex: it takes turns.
Key takeaways
Serial links send bits one at a time, with start and stop bits when asynchronous. Manchester coding puts a clock edge in every bit. Bit rate = baud × \(\log_2 M\). ASK, FSK and PSK modulate a carrier's amplitude, frequency or phase, and M-point QAM carries \(\log_2 M\) bits per symbol. PAM, PWM and PPM vary pulse height, width or position; PCM quantises and codes samples, and delta modulation sends one bit per sample. TDM shares time slots, FDM shares frequency bands, and T1 carries 24 voice channels at 1.544 Mb/s.
Flashcards
Flashcard
Each character sent with a start bit and stop bits
Test your understanding
Question 1 of 5
An 8-PSK modem sends 3000 symbols per second. What is its bit rate?
Question 2 of 5
A pair of handheld radios lets both users talk, but only one at a time. What mode is this?
Question 3 of 5
A PCM system must represent at least 100 distinct levels. How many bits per sample does it need?
Question 4 of 5
A UART uses 8N1 framing at 9600 baud. How many data bytes can it send per second?
Question 5 of 5
What distinguishes frequency-division from time-division multiplexing?
