Electrical Engineering › Section W · Signal conversion and data transmission › Topic W.3

Data transmission media

Every bit that leaves a device travels through something: a copper trace, a cable, a glass fibre or open space. Each medium has its own reach, speed, cost and weaknesses, and choosing well starts with knowing how each one carries a signal.

Sender, medium, receiver

Any data transmission system has three parts: a sending device, a receiving device and the transmission medium between them. The medium can be guided, where the signal follows a conductor or fibre, or unguided, where it spreads through air, space or water as a wave. Every medium weakens the signal with distance, called attenuation, adds noise and limits how fast symbols can change, which caps the data rate. Early theory of these limits came from Harry Nyquist, Ralph Hartley and Claude Shannon in the first half of the twentieth century. This topic takes the data-transmission view: which medium to choose, and how loss, bandwidth and noise limit it. The wave physics behind each medium comes later, in "What electromagnetics is, the spectrum, and wave fundamentals" and "Guided and unguided waves".

Traces, wires and coaxial cable

The simplest medium is a wire or a printed-circuit-board trace, used within a system or between nearby boards. At high speeds even a short trace behaves as a transmission line and needs a controlled impedance. Coaxial cable, or coax, has a centre conductor inside an insulating dielectric, surrounded by a braided or foil shield and an outer jacket. The shield keeps the signal in and blocks electromagnetic interference (EMI) from outside, which makes coax the choice for radio, test equipment (50 Ω) and video and cable television (75 Ω). It carries signals above 1 GHz, so cable networks deliver television and broadband over it, with BNC and F connectors common.

Twisted-pair cable

Twisted-pair cable carries each signal on two insulated wires twisted together. The signal travels as a difference between the wires, and the twist means outside noise induces nearly equal voltages in both, which cancel at a differential receiver, while each pair's own fields largely cancel too. This limits crosstalk, the unwanted coupling of a signal from one pair into another. Unshielded twisted pair (UTP) is cheap and flexible; shielded twisted pair (STP) adds foil or braid for noisy places. Network cables come in categories: Cat 5e is specified to 100 MHz and carries gigabit Ethernet up to 100 m, Cat 6 to 250 MHz (10 Gb/s only to about 55 m), and Cat 6A to 500 MHz for 10 Gb/s Ethernet at 100 m. They end in 8-pin RJ45 connectors.

Worked example: loss along a copper cable

Suppose a twisted-pair cable loses 20 dB per 100 m at the frequency of interest, an assumed figure for this example. How much of the transmitted power reaches the far end of a 60 m run? 1. Loss scales with length: \(20 \times \frac{60}{100} = 12\,\text{dB}\). 2. Decibels for power use \(10\log_{10}\), as in "Logarithms and decibels", so the power ratio is \(10^{-12/10} = 10^{-1.2}\). 3. Evaluate: \(10^{-1.2} \approx 0.063\), so about 6.3% of the power arrives. 4. Check: 10 dB is a factor of 10, so 12 dB must leave a little less than 10%, as found. Loss in copper also rises with frequency, which is why faster links need better categories or shorter runs.

Optical fibre

An optical fibre carries data as pulses of light in a strand of glass or plastic about as thin as a hair. It has a core, a cladding of slightly lower refractive index and a protective jacket; total internal reflection at the core-cladding boundary keeps the light in the core, even around gentle bends. Fibre has very low loss, about 0.2 dB/km in the best single-mode fibre, enormous bandwidth and complete immunity to EMI, but costs more to terminate and needs care in handling.

Multimode and single-mode fibre

In multimode fibre the core is wide, commonly 50 or 62.5 µm, so light follows many paths, or modes, of different lengths. Pulses spread out as they travel, called modal dispersion, which limits multimode links to hundreds of metres at high rates; they suit buildings and data centres. Single-mode fibre has a core of about 8 to 9 µm, carrying essentially one mode, so it reaches tens of kilometres without amplification. All three types share a 125 µm cladding diameter. A fibre link uses a transmitter, an LED or laser modulated by the electrical signal, and a photodiode receiver; LC, SC and multi-fibre MPO connectors are common. One fibre carrying many wavelengths can move many terabits per second.

Worked example: a fibre loss budget

A single-mode link is 40 km long. The fibre loses 0.25 dB/km, each of 2 connectors loses 0.5 dB and each of 4 splices loses 0.1 dB. 1. Fibre loss: \(40 \times 0.25 = 10.0\,\text{dB}\). 2. Connectors: \(2 \times 0.5 = 1.0\,\text{dB}\). 3. Splices: \(4 \times 0.1 = 0.4\,\text{dB}\). 4. Total: \(10.0 + 1.0 + 0.4 = 11.4\,\text{dB}\). 5. Power ratio: \(10^{-11.4/10} \approx 0.072\), so about 7.2% of the launched light arrives. 6. Engineers compare the total with the gap between transmitter power and receiver sensitivity, keeping a few decibels spare for ageing and repairs.

Wireless transmission and the spectrum

Wireless transmission sends data through air or space as electromagnetic waves, with no physical connection. Data links mostly use radio waves, microwaves and infrared, the low-frequency end of the spectrum. Its great advantages are mobility and no cabling; its costs are a shared, regulated band, interference from other users, and power that spreads out with distance. Underwater, where radio fades quickly, sonar uses sound, which is not electromagnetic. Every medium's limit can be stated with Shannon's capacity formula,

C = B\log_2\!\left(1 + \frac{S}{N}\right)

the highest error-free bit rate C for a bandwidth B in hertz and a signal-to-noise power ratio S/N. A 3.1 kHz phone channel with S/N = 1000 (30 dB) allows about 30.9 kb/s.

How radio waves travel

Radio signals reach a receiver in three main ways. Ground waves, at low frequencies up to a few megahertz, follow the Earth's curvature, which is how AM broadcasts reach beyond the horizon. Sky waves, mainly in the shortwave range of about 3 to 30 MHz, are bent back by the ionosphere and can cross oceans, but they vary with time of day, season and solar activity. At VHF and above, signals travel by line of sight: the antennas must see each other, so range depends on their heights, for example about 100 km between two 150 m towers. Relay towers and satellites extend line-of-sight links. Infrared links, such as remote controls, need a direct path or a diffuse reflection from walls.

Common mistakes to avoid

First, thinking fibre cladding is a mirror: light is held by total internal reflection because the cladding has a lower refractive index. Second, confusing bandwidth in hertz with data rate in bits per second. Third, adding loss ratios instead of decibels: losses in dB add, the ratios multiply. Fourth, using \(20\log_{10}\) for a power ratio: power uses \(10\log_{10}\). Fifth, assuming twisted pair is a low-frequency medium: modern categories carry hundreds of megahertz.

Key takeaways

A transmission system is a sender, a medium and a receiver; media attenuate, add noise and limit speed. Coax shields a centre conductor and comes in 50 Ω and 75 Ω types. Twisted pair cancels noise and crosstalk by twisting; Cat 5e, 6 and 6A are rated to 100, 250 and 500 MHz. Optical fibre guides light by total internal reflection, with very low loss and no EMI; multimode suits short runs, single-mode long ones. Losses in dB add along a link. Shannon's \(C = B\log_2(1 + S/N)\) caps any channel's bit rate. Wireless uses radio, microwaves and infrared, travelling by ground wave, sky wave or line of sight.

Flashcards

Flashcard

Transmission system

Sending device, transmission medium, receiving device

The medium can be guided or unguided.

Test your understanding

Question 1 of 5

Why does twisting the two wires of a pair reduce interference?

Question 2 of 5

A fibre link has 30 km of fibre at 0.30 dB/km, two connectors at 0.75 dB each and no splices. What is the total loss?

Question 3 of 5

What keeps light inside the core of an optical fibre?

Question 4 of 5

A channel has a bandwidth of 1.0 MHz and a signal-to-noise power ratio of 100 (20 dB). What is its Shannon capacity, to three significant figures?

Question 5 of 5

A building needs a 10 Gb/s copper Ethernet run of 90 m. Which cable category is the lowest that is specified for it?

← Previous topicNext topic →