Electrical Engineering › Section F · Network theorems (dc) › Topic F.3
Norton's theorem
Norton's theorem is the mirror image of Thevenin's: it models any linear two-terminal network as a current source with a resistor in parallel. Knowing both forms, and how to switch between them, lets you choose whichever makes a problem shortest.
The other way to model a network
Thevenin's theorem reduces a network to a voltage source with a series resistance. That is natural when the load is in series with the source, but some problems are easier with a current source. Several sources feeding the same pair of terminals, for example, combine by simple addition when each is a current source in parallel with a resistor. Some devices also behave more like current sources than voltage sources: over its normal operating range a transistor's output, met later in the electronics part of this course, is modelled that way. Norton's theorem provides the current-source form.
The theorem
Any linear two-terminal dc network is equivalent, at its terminals, to an ideal current source \(I_N\) in parallel with a resistance \(R_N\). As with Thevenin's form, the equivalence holds only at the terminals: any load sees the same voltage and current as it would from the original network. Edward Norton, an engineer at Bell Laboratories in the United States, described the result in an internal memorandum in 1926, and Hans Ferdinand Mayer of Siemens in Germany published the same idea that year, so it is sometimes called the Mayer-Norton theorem.
Finding the Norton current
Remove the load and connect a short circuit between the two terminals. The Norton current is the current that flows through that short:
Use any dc method to find it. Shorting the terminals often puts some resistors in parallel with the short, so they carry no current and drop out of the calculation; others end up in parallel with each other. Mark the direction carefully. The current source in the equivalent must push current out of the same terminal that the short-circuit current leaves the network from.
Finding the Norton resistance
The Norton resistance is found in exactly the same way as the Thevenin resistance: switch every independent source off, with ideal voltage sources shorted and ideal current sources opened, and find the resistance looking into the open terminals. So
The two equivalents of one network always share the same resistance. The only difference is where it sits: in series with the source in Thevenin's form, and in parallel with it in Norton's. If dependent sources are present, use \(R_N = V_{oc}/I_{sc}\) instead.
Worked example: a Norton equivalent
An 18 V source, − to ground, feeds node a through \(R_1 = 2.2\,\text{k}\Omega\). \(R_2 = 4.7\,\text{k}\Omega\) joins a to ground and \(R_3 = 1.0\,\text{k}\Omega\) runs from a to terminal b; the load goes between b and ground. 1. \(I_N\): short b to ground, so \(R_3\) is in parallel with \(R_2\), giving \(0.825\,\text{k}\Omega\). The source sees \(3.02\,\text{k}\Omega\) and supplies 5.95 mA, and the current divider sends \(5.95 \times \frac{4.7}{5.7} = 4.91\,\text{mA}\) through \(R_3\) and the short. 2. \(R_N\): short the source; \(R_1 \parallel R_2 = 1.50\,\text{k}\Omega\) plus \(R_3\) gives \(2.50\,\text{k}\Omega\). 3. Use it: a 2.2 kΩ load takes \(4.91 \times \frac{2.50}{4.70} = 2.61\,\text{mA}\) by the current divider. 4. Check: the open-circuit voltage is \(18 \times \frac{4.7}{6.9} = 12.3\,\text{V}\), and \(12.3 \div 2.50 = 4.91\,\text{mA}\), as it should.
Switching between Norton and Thevenin
Because both forms describe the same terminals, converting one to the other is the source conversion from Current sources and source conversions:
with the resistance unchanged. In the worked example, \(4.91\,\text{mA} \times 2.50\,\text{k}\Omega = 12.3\,\text{V}\), which is the open-circuit voltage found in the check. So any two of \(V_{oc}\), \(I_{sc}\) and \(R_{Th}\) give the third. The conversion needs a resistance: an ideal voltage source has no Norton form, because its short-circuit current would be infinite, and an ideal current source has no Thevenin form.
Worked example: two current sources in parallel
Two practical sources feed terminal b, with ground as the return. Source A is 4.0 mA in parallel with 10 kΩ; source B is 2.5 mA in parallel with 15 kΩ; both push current into b. A 3.3 kΩ load connects from b to ground. 1. Combine: the currents point the same way, so \(I_N = 4.0 + 2.5 = 6.5\,\text{mA}\). 2. The resistors are in parallel: \(R_N = 10 \parallel 15 = 6.0\,\text{k}\Omega\). 3. Load current by the current divider:
so the load has 13.8 V across it. 4. Check with the Thevenin form: \(E_{Th} = 6.5 \times 6.0 = 39\,\text{V}\), and \(39 \div 9.3\,\text{k}\Omega = 4.19\,\text{mA}\).
Measuring and using the Norton form
On the bench, \(I_N\) can be measured by connecting an ammeter straight across the terminals, since an ideal ammeter is a short. Do this only when the source is designed to survive a short, such as a current-limited bench supply; a battery or a mains-derived supply can deliver a dangerous current. \(R_N\) then follows from an open-circuit voltage reading, \(R_N = V_{oc}/I_{sc}\). Choose Norton's form when loads or sources are in parallel, since the current divider then gives the answer at once; choose Thevenin's when they are in series.
Common mistakes to avoid
First, finding \(I_N\) with the terminals open instead of shorted; the open-circuit current is always zero. Second, drawing \(R_N\) in series with the current source, which turns it into a different circuit. Third, getting the source direction backwards: the equivalent must push current out of the terminal the short-circuit current leaves from. Fourth, thinking \(R_N\) and \(R_{Th}\) are different; for the same terminals they are equal. Fifth, multiplying when converting the wrong way: \(I_N = E_{Th}/R_{Th}\), not \(E_{Th} \times R_{Th}\).
Key takeaways
Norton's theorem replaces any linear two-terminal network with a current source \(I_N\) in parallel with \(R_N\), exact at the terminals. \(I_N\) is the short-circuit current at the terminals. \(R_N\) equals \(R_{Th}\), found with independent sources switched off or as \(V_{oc}/I_{sc}\). Converting between the forms uses \(E_{Th} = I_N R_N\). Parallel current sources add, and their resistors combine in parallel, which makes Norton's form the quick choice for parallel arrangements.
Flashcards
Flashcard
An ideal current source I_N in parallel with a resistance R_N
Test your understanding
Question 1 of 5
A network is simply a 12 V source, − to ground, connected to terminal a through 3.3 kΩ. What is its Norton equivalent between a and ground?
Question 2 of 5
A Norton equivalent is 2.0 mA in parallel with 4.7 kΩ. What is the Thevenin voltage of the same network?
Question 3 of 5
A 10 V source, − to ground, feeds node a through 1.0 kΩ. Another 1.0 kΩ joins a to ground, and a third 1.0 kΩ runs from a to terminal b. What is the Norton current between b and ground?
Question 4 of 5
A Norton source of 5.0 mA in parallel with 2.2 kΩ drives a 3.3 kΩ load. What current flows in the load?
Question 5 of 5
For the same pair of terminals, which statement about a network's Norton and Thevenin equivalents is true?
