Electrical Engineering › Section F · Network theorems (dc) › Topic F.2

Thevenin's theorem

However many sources and resistors sit behind two terminals, a linear network looks to the outside world like one voltage source and one resistor. Thevenin's theorem tells you how to find that pair, and once you have it, every load can be analysed in a single line.

A whole network as one source

Suppose a network feeds a load resistor and you need the load current for ten different load values. Re-solving the full network ten times is tedious. Thevenin's theorem removes the repetition. You pick the two terminals where the load connects, replace everything on the other side by a simple equivalent once, and then each load becomes a two-resistor series circuit. The same idea explains why a battery's voltage sags under load, a point met in Internal resistance and voltage regulation, and it is how datasheets describe the outputs of sensors and amplifiers.

The theorem

Seen from its two terminals, any linear dc network behaves exactly like one ideal voltage source \(E_{Th}\) in series with one resistance \(R_{Th}\). The equivalent is exact as far as the terminals are concerned: any load connected to it draws the same current, at the same voltage, as it would from the original network. It says nothing about what happens inside, so the equivalent cannot tell you the power wasted in the original resistors. The French telegraph engineer Léon Thevenin published the result in 1883; Hermann von Helmholtz had stated it about thirty years earlier, so some books call it the Helmholtz-Thevenin theorem.

Finding the Thevenin voltage

First remove the load and mark the two terminals, say b and 0. The Thevenin voltage is the open-circuit voltage between them:

E_{Th} = V_{oc}

With nothing connected, no current flows out of the terminals, so any resistor in series with a terminal carries no current and drops no voltage. Find \(V_{oc}\) with whatever dc method suits the network: a voltage divider for a simple chain, superposition when there are several sources, or nodal analysis for anything larger. Keep track of polarity, because \(E_{Th}\) has a + terminal like any source.

Finding the Thevenin resistance

Next, switch every independent source off, exactly as in The superposition theorem: ideal voltage sources become short circuits and ideal current sources become open circuits, while internal resistances stay. Then \(R_{Th}\) is the resistance you would measure looking into the two open terminals. Work outwards from the terminals using series and parallel combinations. A resistor in series with a terminal adds directly; resistors on the far side of a shorted voltage source often end up in parallel. If the network contains dependent sources, which cannot be switched off, use the open-circuit and short-circuit method below.

Worked example: a loaded divider

A 24 V source, − to ground, feeds node a through \(R_1 = 6.8\,\text{k}\Omega\). \(R_2 = 3.3\,\text{k}\Omega\) joins a to ground, and \(R_3 = 1.0\,\text{k}\Omega\) runs from a to terminal b. Loads connect between b and ground. 1. \(E_{Th}\): with no load, \(R_3\) carries no current, so b sits at the divider voltage \(24 \times \frac{3.3}{10.1} = 7.84\,\text{V}\). 2. \(R_{Th}\): short the source, so \(R_1\) and \(R_2\) are in parallel, \(2.22\,\text{k}\Omega\), in series with \(R_3\): \(R_{Th} = 3.22\,\text{k}\Omega\). 3. Use it: a 4.7 kΩ load draws

I_L = \frac{7.84}{3.22 + 4.7} = 0.990\,\text{mA}

with 4.65 V across it. A 10 kΩ load draws 0.593 mA at 5.93 V. 4. Check: nodal analysis of the original circuit with the 4.7 kΩ load gives 0.990 mA as well.

Worked example: two sources

A 12 V source, + towards node a, is in series with \(R_1 = 2.2\,\text{k}\Omega\) from ground to a. A 3.0 mA current source pushes current from ground into a, \(R_2 = 4.7\,\text{k}\Omega\) joins a to ground, and \(R_3 = 1.5\,\text{k}\Omega\) runs from a to terminal b. 1. \(E_{Th}\) by superposition, with b open: the 12 V source alone gives \(12 \times \frac{4.7}{6.9} = 8.17\,\text{V}\); the current source alone gives \(3.0\,\text{mA} \times (2.2 \parallel 4.7) = 4.50\,\text{V}\). Both raise a, so \(E_{Th} = 12.7\,\text{V}\). 2. \(R_{Th}\): short the voltage source and open the current source, leaving \(R_3 + R_1 \parallel R_2 = 1.5 + 1.50 = 3.00\,\text{k}\Omega\). 3. A 3.3 kΩ load would then draw \(\frac{12.7}{6.3} = 2.01\,\text{mA}\) and have 6.64 V across it.

The open-circuit and short-circuit check

There is a second route to \(R_{Th}\). Short the terminals together and find the short-circuit current \(I_{sc}\) that flows through the short. Since the equivalent is \(E_{Th}\) in series with \(R_{Th}\), shorting it gives \(I_{sc} = E_{Th}/R_{Th}\), so

R_{Th} = \frac{V_{oc}}{I_{sc}}

In the two-source example, shorting b to ground puts \(R_3\) from a to ground; nodal analysis gives \(I_{sc} = 4.23\,\text{mA}\), and \(12.7 \div 4.23 = 3.00\,\text{k}\Omega\), agreeing with the first method. This route also works for networks containing dependent sources, which cannot simply be switched off.

Measuring a Thevenin equivalent

You can find the equivalent of real hardware without knowing its circuit. 1. Measure the open-circuit voltage with a high-resistance voltmeter: this is \(E_{Th}\). 2. Connect a known load and measure its voltage \(V_L\). The divider formula rearranges to

R_{Th} = R_L\left(\frac{V_{oc}}{V_L} - 1\right)

For example, 9.00 V open-circuit falling to 7.50 V with a 10 kΩ load gives \(R_{Th} = 10 \times 0.200 = 2.00\,\text{k}\Omega\). A variant uses a potentiometer as the load, adjusted until the voltage is half of \(V_{oc}\); then its resistance equals \(R_{Th}\). Measuring \(I_{sc}\) directly with an ammeter is quicker but only safe when the source can tolerate a short.

Common mistakes to avoid

First, leaving the load connected while finding \(V_{oc}\); the load must be removed. Second, switching sources off the wrong way when finding \(R_{Th}\), or forgetting a source's internal resistance. Third, forgetting that a resistor in series with an open terminal drops no voltage, and then dividing across it anyway. Fourth, looking into the wrong pair of terminals: \(R_{Th}\) depends on where the load connects. Fifth, using the equivalent to find power inside the original network; it only reproduces what happens at the terminals.

Key takeaways

Thevenin's theorem replaces any linear two-terminal network by a source \(E_{Th}\) in series with \(R_{Th}\), exact at the terminals only. \(E_{Th}\) is the open-circuit voltage with the load removed. \(R_{Th}\) is the resistance looking into the terminals with independent sources switched off, or \(V_{oc}/I_{sc}\). Once found, every load is a simple series circuit. In the laboratory, an open-circuit reading plus one loaded reading gives \(R_{Th} = R_L(V_{oc}/V_L - 1)\).

Flashcards

Flashcard

Thevenin equivalent

An ideal voltage source E_Th in series with a resistance R_Th

Replaces a linear two-terminal network.

Test your understanding

Question 1 of 5

A 15 V source, − to ground, feeds terminal a through 2.2 kΩ, and 3.3 kΩ joins a to ground. What is the Thevenin equivalent seen between a and ground?

Question 2 of 5

A network has E_Th = 10 V and R_Th = 2.2 kΩ. What voltage appears across a 2.7 kΩ load connected to it?

Question 3 of 5

Looking into terminals b and ground, a network has a 5 mA ideal current source in parallel with 1.0 kΩ, and that pair connects to b through a 2.2 kΩ resistor. What is R_Th?

Question 4 of 5

A sensor reads 6.0 V with nothing connected and 4.0 V with a 1.0 kΩ load across it. What is its Thevenin resistance?

Question 5 of 5

Which statement correctly describes the Thevenin voltage of a network?

← Previous topicNext topic →