Electrical Engineering › Section L · Power (ac) and resonance › Topic L.7
Parallel resonance
Put the inductor and capacitor side by side instead of in a row and resonance turns inside out: the impedance peaks instead of dipping, and a large current circulates inside the pair while the source supplies only a trickle. This tank circuit sits at the heart of oscillators and tuned amplifiers.
Resonance turned inside out
In a series resonant circuit the impedance is smallest at resonance, so a voltage source drives a large current. A parallel resonant circuit does the opposite: its impedance is largest at resonance, so a current source produces a large voltage across it. The ideal version is a current source \(I\) feeding \(R\), \(L\) and \(C\) all in parallel. Its admittance is
The imaginary part vanishes when \(X_L = X_C\), at the familiar \(f = 1/(2\pi\sqrt{LC})\). There \(Z_T = R\), its maximum, and the voltage \(V = IR\) peaks. Real circuits are not quite this tidy, because the coil's resistance sits in series with its inductance.
The practical tank circuit
A practical tank circuit is a capacitor \(C\) in parallel with a coil, modelled as inductance \(L\) in series with winding resistance \(R_l\). Using the series-to-parallel conversion from "Equivalent circuits and phase measurement", the coil branch \(R_l + jX_L\) is replaced by a resistance \(R_p\) in parallel with a reactance \(X_{Lp}\):
The driving source is usually a current source with internal resistance \(R_s\), so the total parallel resistance is \(R = R_s \parallel R_p\). The result looks like the ideal circuit, except that \(R_p\) and \(X_{Lp}\) change with frequency.
Two resonant frequencies
Because \(R_p\) and \(X_{Lp}\) depend on frequency, the frequency of unity power factor and the frequency of maximum impedance are no longer the same. Unity power factor needs \(X_{Lp} = X_C\), which gives
where \(f_s = 1/(2\pi\sqrt{LC})\). Note that \(R_s\) does not appear. Maximum impedance, and so maximum voltage, occurs at \(f_m\), found by calculus: with \(k = R_l^2C/L\),
In general \(f_p < f_m < f_s\), and both approach \(f_s\) as \(R_l\) shrinks. At \(f_p\) the equivalent resistance works out exactly to \(R_p = L/(R_lC)\).
The high-Q approximations
Most practical tanks have a coil quality factor \(Q_l = X_L/R_l\) of 10 or more, and then the algebra collapses. \(X_{Lp} \approx X_L\), so \(f_p \approx f_m \approx f_s\), and
The impedance at resonance is \(Z_{Tp} = R_s \parallel R_p\). The circuit's quality factor is the ratio of reactive to real power, which gives \(Q_p = Z_{Tp}/X_L\). With an ideal current source (\(R_s \to \infty\)), \(Q_p\) equals \(Q_l\); a finite \(R_s\) always lowers it. The bandwidth is
where \(R = R_s \parallel R_p\).
Current magnification
At resonance the voltage across the tank is \(V = IZ_{Tp}\), so the capacitor current is \(I_C = V/X_C = IZ_{Tp}/X_C\). With \(X_C = X_L\) this becomes
The parallel circuit magnifies current the way the series circuit magnifies voltage. A large current circulates around the loop formed by the coil and capacitor, carrying the stored energy back and forth, while the source supplies only the small current that makes up the losses. Like series voltage magnification, this matters for component ratings: the capacitor and coil must carry \(Q_p\) times the drive current.
Response and phase
The impedance of a parallel resonant circuit is about \(R_l\) at zero frequency, rises to its peak near \(f_s\), and falls towards zero at high frequency. With a constant source current, the tank voltage \(V = IZ_T\) has the same shape, and its 0.707 points define \(f_1\), \(f_2\) and the bandwidth just as in the topic "Impedance versus frequency and selectivity". The phase behaves the opposite way to the series circuit. Below resonance the inductor's low reactance dominates, so the tank is inductive and the power factor lagging; above resonance the capacitor dominates and it is capacitive and leading; at \(f_p\) it is purely resistive. Raising \(R_l\) or lowering \(L/C\) lowers the peak and widens the band.
Worked example: a low-Q tank
A 1.0 mH coil with \(R_l = 22\,\Omega\) is in parallel with a 47 nF capacitor, fed by an ideal 1.0 mA current source. 1. \(f_s = 1/(2\pi\sqrt{10^{-3} \times 47\times10^{-9}}) = 23.22\) kHz, where \(X_L = 146\,\Omega\) and \(Q_l = 6.63\), below 10. 2. \(k = R_l^2C/L = 0.0227\), so \(f_p = f_s\sqrt{1 - k} = 22.95\) kHz. 3. \(f_m = f_s\sqrt{\sqrt{1 + 2k} - k} = 23.21\) kHz. 4. At \(f_p\), \(R_p = L/(R_lC) = 967\,\Omega\), so \(V = 0.967\) V. 5. \(X_{Lp} = X_C = 147.6\,\Omega\) at \(f_p\), so \(Q_p = 967/147.6 = 6.55\) and \(\text{BW} = 22.95/6.55 = 3.50\) kHz. 6. Compare: the high-Q shortcut puts resonance at 23.22 kHz, only 1.2% above \(f_p\), even at this modest \(Q_l\).
Worked example: a tuned amplifier stage
A transistor stage acts as a 0.10 mA current source with \(R_s = 47\) kΩ, driving a 2.2 mH coil (\(R_l = 22\,\Omega\)) in parallel with 470 pF. 1. \(f_s = 156.5\) kHz, \(X_L = 2164\,\Omega\), \(Q_l = 98.3\): use the approximations, so \(f_p \approx 156.5\) kHz. 2. \(R_p = Q_l^2R_l = 213\) kΩ. 3. \(Z_{Tp} = 47\text{ k}\Omega \parallel 213\text{ k}\Omega = 38.5\) kΩ. 4. \(Q_p = 38\,500/2164 = 17.8\), so \(\text{BW} = 156.5/17.8 = 8.80\) kHz. 5. \(V = IZ_{Tp} = 3.85\) V, and \(I_C \approx Q_pI = 1.78\) mA. 6. With an ideal source, \(Q_p = 98.3\), BW 1.59 kHz and \(V = 21.3\) V: the source resistance cut \(Q_p\) by more than five times.
Applications and stray resonance
Tank circuits set the frequency of many oscillators and select one band in the intermediate-frequency stages of radio receivers, where the transistor's output behaves like the current source above. Audio graphic equalisers use a bank of band filters, each centred on its own resonant frequency, to lift or cut each part of the spectrum. Resonance can also appear where nobody designed it. The inductance of a lead or a winding and the stray capacitance between nearby conductors form unintended L-C pairs, and an unexpected peak in a measured frequency response is very often such a stray resonance. Curing it means changing the layout or adding damping, while taking care not to create a new resonance.
Common mistakes to avoid
First, assuming the tank's impedance is smallest at resonance, as in the series case: it is largest. Second, putting the coil's \(R_l\) in parallel with the tank; it is in series with \(L\) and must be converted to \(R_p \approx Q_l^2R_l\). Third, forgetting the source resistance, which appears in \(Z_{Tp} = R_s \parallel R_p\) and can lower \(Q_p\) and widen the band dramatically. Fourth, using the high-Q shortcuts without first checking \(Q_l \ge 10\). Fifth, reversing the phase: a parallel tank is inductive below resonance and capacitive above.
Key takeaways
A parallel resonant circuit has maximum impedance at resonance, so a current source produces a peak voltage across it. With coil resistance \(R_l\), \(f_p = f_s\sqrt{1 - R_l^2C/L}\) (unity power factor) is below \(f_m\) (maximum impedance), which is below \(f_s\). For \(Q_l \ge 10\): \(f_p \approx f_m \approx f_s\), \(R_p \approx Q_l^2R_l = L/(R_lC)\), \(Z_{Tp} = R_s \parallel R_p\), \(Q_p = Z_{Tp}/X_L\), \(\text{BW} = f_p/Q_p\), and \(I_C \approx I_L \approx Q_pI\). Source resistance lowers \(Q_p\). The tank is inductive below resonance and capacitive above.
Flashcards
Flashcard
Maximum impedance at resonance, driven by a current source
Test your understanding
Question 1 of 5
A tank circuit uses a coil with Q_l = 40 and R_l = 5 Ω, fed by an ideal current source. What is its impedance at resonance?
Question 2 of 5
A tank has R_p = 100 kΩ and X_L = X_C = 2.0 kΩ at resonance, driven by a current source with R_s = 25 kΩ. What is Q_p?
Question 3 of 5
A parallel tank with Q_p = 25 is driven at resonance by a 2.0 mA current source. About how large is the current in the capacitor?
Question 4 of 5
How does a practical parallel tank circuit behave at a frequency well below its resonant frequency?
Question 5 of 5
For a tank with a coil resistance R_l, how do f_p (unity power factor), f_m (maximum impedance) and f_s = 1/(2π√LC) compare?
