Electrical Engineering › Section I · Sinusoidal waveforms and phasors › Topic I.8

Phasors

A phasor is a complex number that stands in for a whole sinusoid. With phasors, adding two voltages that are out of step takes a few lines of complex arithmetic instead of a page of graph paper, and the same notation runs through every ac topic that follows.

Adding sinusoids the long way

Kirchhoff's laws still hold in ac circuits at every instant, so the voltage across two series elements is \(v_a + v_b\). If the two sinusoids have the same frequency but different phase angles, their sum is another sinusoid of that frequency, but finding its peak and phase by adding the graphs point by point is slow and imprecise. Trigonometric identities work but quickly get messy. Phasors solve the problem by replacing each sinusoid with a complex number, using the toolkit of "Complex numbers in rectangular and polar form", and adding those instead.

The phasor as a frozen rotating vector

Recall the rotating vector of "Sinusoidal waveforms and their general format": an arrow of length \(V_m\) turning anticlockwise at \(\omega\), whose vertical projection traces \(V_m \sin(\omega t + \theta)\). At \(t = 0\) it points at angle \(\theta\). Every sinusoid in a circuit has the same \(\omega\), so all their arrows turn together and keep the same angles between them. Nothing is lost by freezing the picture at \(t = 0\). That snapshot of one arrow, a length and an angle, is the phasor, and the snapshot of several arrows together is a phasor diagram.

The course's phasor convention

This course writes a phasor in bold with an rms magnitude and an angle in degrees, with the sine as the reference:

v(t) = \sqrt{2}\,V \sin(\omega t + \theta) \iff \mathbf{V} = V\angle\theta

Here \(V\) is the rms value, so the peak is \(V_m = \sqrt{2}\,V\), and \(\theta\) is the same phase angle, in radians inside a sine with a numerical \(\omega\) and in degrees in the phasor. The frequency does not appear in the phasor; it is understood from the circuit. A phasor can be written in polar form, \(10\angle 30^\circ\,\text{V}\), or in rectangular form, \(8.66 + j5\,\text{V}\), and you should say which you are using.

Two warnings about phasors

First, phasor arithmetic only works for sinusoids of one frequency. Signals at different frequencies rotate at different rates, so a single snapshot cannot represent their sum; each frequency must be handled separately. Second, conventions differ between books. Some use the cosine as the reference and the peak value as the magnitude, so their \(10\angle 0^\circ\) means \(10\cos\omega t\). In this course it means \(10\sqrt{2}\sin\omega t\). Before using a formula or answer from another source, check its reference function and whether its magnitudes are peak or rms. A cosine converts with \(\cos x = \sin(x + \pi/2)\), which adds 90° to the phasor angle.

Worked example: converting both ways

1. Time to phasor: \(i = 8\sin(377t - \pi/9)\,\text{A}\). The rms value is \(8/\sqrt{2} = 5.66\,\text{A}\) and \(-\pi/9\) rad is −20°, so \(\mathbf{I} = 5.66\angle -20^\circ\,\text{A}\). 2. Phasor to time: \(\mathbf{V} = 120\angle 30^\circ\,\text{V}\) at 60 Hz. The peak is \(\sqrt{2} \times 120 = 169.7\,\text{V}\), \(\omega = 377\,\text{rad/s}\) and 30° is \(\pi/6\), so \(v = 169.7\sin(377t + \pi/6)\,\text{V}\). 3. A cosine: \(v = 50\cos\omega t = 50\sin(\omega t + \pi/2)\), so \(\mathbf{V} = 35.4\angle 90^\circ\,\text{V}\). 4. Check: a 120 V rms phasor gives the familiar 170 V peak of US mains.

The method for adding sinusoids

Because every same-frequency sinusoid is the projection of a rotating arrow, adding the sinusoids is the same as adding the arrows, which is complex addition. So Kirchhoff's laws hold for phasors: \(\sum \mathbf{V} = 0\) around a loop and \(\sum \mathbf{I} = 0\) at a node. The method has five steps. 1. Convert each sinusoid to a polar phasor. 2. Convert each phasor to rectangular form. 3. Add or subtract the real parts and the imaginary parts. 4. Convert the result back to polar form. 5. Convert back to the time domain if the waveform is wanted. The laws do not hold for rms meter readings, which ignore phase.

Worked example: two series voltages

Two elements in series between nodes a and 0 have \(v_1 = 30\sin(\omega t + \pi/6)\,\text{V}\) and \(v_2 = 40\sin(\omega t - \pi/3)\,\text{V}\). Find the total \(v = v_1 + v_2\). 1. Phasors: \(\mathbf{V}_1 = 21.21\angle 30^\circ\) and \(\mathbf{V}_2 = 28.28\angle -60^\circ\,\text{V}\). 2. Rectangular: \(18.37 + j10.61\) and \(14.14 - j24.49\). 3. Sum: \(32.51 - j13.89\,\text{V}\). 4. Polar: \(\mathbf{V} = 35.36\angle -23.13^\circ\,\text{V}\). 5. Time domain: the peak is \(\sqrt{2} \times 35.36 = 50.0\,\text{V}\) and −23.13° is −0.404 rad, so \(v = 50.0\sin(\omega t - 0.404)\,\text{V}\). Check: the two waves are 90° apart, so the peaks combine like the sides of a 3-4-5 triangle: \(\sqrt{30^2 + 40^2} = 50\).

Worked example: a missing branch current

At node a a total current \(i_T = 10\sin(\omega t + \pi/3)\,\text{A}\) divides between two parallel branches. One branch carries \(i_1 = 6\sin\omega t\,\text{A}\). Find \(i_2\). 1. By KCL, \(\mathbf{I}_2 = \mathbf{I}_T - \mathbf{I}_1\). 2. Phasors: \(\mathbf{I}_T = 7.07\angle 60^\circ\), which is \(3.54 + j6.12\,\text{A}\), and \(\mathbf{I}_1 = 4.24\angle 0^\circ = 4.24 + j0\,\text{A}\). 3. Subtract: \(\mathbf{I}_2 = -0.71 + j6.12\,\text{A}\). 4. Polar, in the second quadrant: \(\mathbf{I}_2 = 6.16\angle 96.6^\circ\,\text{A}\). 5. Time domain: \(i_2 = 8.72\sin(\omega t + 1.69)\,\text{A}\). Check: the branch peaks, 6 A and 8.72 A, add to more than the 10 A total, which only phasors can explain.

Phasor diagrams and the elements

A phasor diagram draws each phasor as an arrow from the origin, with one chosen as the reference at 0°. Sums can be drawn head to tail, which makes a quick check on the arithmetic. The element rules of "Response of R, L, and C to sinusoids" become simple statements about arrows. A resistor's \(\mathbf{V}\) and \(\mathbf{I}\) point the same way. An inductor's \(\mathbf{V}\) is 90° ahead of its \(\mathbf{I}\), so \(\mathbf{V} = jX_L\mathbf{I}\). A capacitor's \(\mathbf{V}\) is 90° behind, so \(\mathbf{V} = -jX_C\mathbf{I}\). "Impedance, phasor diagrams, and series ac circuits" builds the whole of ac analysis on these relations.

Why calculus becomes algebra

Differentiating \(\sqrt{2}\,V\sin(\omega t + \theta)\) gives \(\sqrt{2}\,\omega V\sin(\omega t + \theta + \pi/2)\): the size is multiplied by \(\omega\) and the angle advanced by 90°. In phasor terms that is multiplication by \(\omega\angle 90^\circ = j\omega\). So differentiation becomes multiplication by \(j\omega\), and integration becomes division by \(j\omega\). That is why \(v_L = L\,di/dt\) turns into \(\mathbf{V} = j\omega L\,\mathbf{I}\), and why circuits with inductors and capacitors can be solved with algebra rather than differential equations.

Common mistakes to avoid

First, using the peak as the phasor magnitude, which makes every later power result twice too large. Second, adding phasor magnitudes directly instead of adding in rectangular form. Third, combining phasors of different frequencies. Fourth, forgetting to convert a cosine or a negative amplitude before writing the phasor. Fifth, leaving a degree angle inside the sine when returning to the time domain; write \(\sin(377t + \pi/6)\), not a mixture of radians and degrees.

Key takeaways

A phasor is the t = 0 snapshot of a sinusoid's rotating vector. The course convention is v(t) = √2 V sin(ωt + θ) ⇔ V = V∠θ: rms magnitude, angle in degrees, sine reference, frequency understood. Phasors apply only to one frequency at a time; check other books' references before borrowing results. Kirchhoff's laws hold for phasors, so add sinusoids by converting to phasors, adding in rectangular form and converting back. On a phasor diagram, inductor voltage leads current by 90° (V = jX_L I) and capacitor voltage lags by 90° (V = −jX_C I). Differentiation becomes multiplication by jω.

Flashcards

Flashcard

Phasor

A complex number standing for a sinusoid's size and phase

The t = 0 snapshot of its rotating vector.

Test your understanding

Question 1 of 5

In the course convention, what is the phasor for v = 100 sin(ωt − π/4) V?

Question 2 of 5

The phasor I = 2∠−30° mA describes a 1 kHz current. What is i(t)?

Question 3 of 5

Two series voltages have phasors 3∠0° V and 4∠90° V. What is the phasor of their sum?

Question 4 of 5

Which pair of signals cannot be added by phasor arithmetic alone?

Question 5 of 5

A 50 mH inductor carries a current with phasor I = 2∠0° A at ω = 1000 rad/s. What is the phasor of its voltage?

← Previous topicNext topic →