Electrical Engineering › Section J · Series, parallel, and series-parallel ac circuits › Topic J.1
Impedance, phasor diagrams, and series ac circuits
Once every resistor, inductor and capacitor is described by a single complex number of ohms, an ac circuit can be solved with the same Ohm's law, series rules and voltage divider you used for dc. This topic builds that number, impedance, and puts it to work on series circuits.
From reactance to impedance
The topic "Response of R, L, and C to sinusoids" gave each element a reactance, and "Phasors" showed how to treat a sinusoid as a complex number. Combine the two and every element obeys one law. The impedance of an element or network is the ratio of its phasor voltage to its phasor current:
Bold letters here are phasors and plain letters their rms magnitudes. Impedance is measured in ohms and is complex, \(Z = R + jX\), with resistance R and reactance X. Its magnitude is the rms ratio \(V/I\); its angle is how far the voltage leads the current. Impedance is not a phasor: it stands for no sinusoid, so it has no time function.
Impedance of R, L and C
Apply the definition to each element. A resistor's voltage and current are in phase, so \(Z_R = R\angle 0^\circ\). An inductor's voltage leads its current by 90°, so \(Z_L = X_L\angle 90^\circ = jX_L\), with \(X_L = \omega L\). A capacitor's current leads its voltage by 90°, so \(Z_C = X_C\angle -90^\circ = -jX_C\), with \(X_C = 1/(\omega C)\). The reactances \(X_L\) and \(X_C\) are positive numbers of ohms; the \(j\) or \(-j\) carries the phase. Ohm's law in phasor form, \(\mathbf{V} = \mathbf{I}Z\), now gives magnitude and phase in one step, because multiplying by \(j\) rotates a phasor 90° ahead and multiplying by \(-j\) rotates it 90° behind.
Worked example: an inductor on its own
A 47 mH inductor is connected across a 24 V, 60 Hz supply, \(\mathbf{E} = 24\angle 0^\circ\,\text{V}\). Find the current. 1. Reactance: \(X_L = 2\pi(60)(0.047) = 17.7\,\Omega\), so \(Z_L = 17.7\angle 90^\circ\,\Omega\). 2. Ohm's law:
3. Back to the time domain: the peak current is \(\sqrt{2} \times 1.354 = 1.92\) A and \(\omega = 377\) rad/s. Taking \(v(t) = 33.9\sin 377t\) V, the current is \(i(t) = 1.92\sin(377t - \pi/2)\) A, the phase in radians because ω is a number. 4. Check: the current lags the voltage by 90°, as it must in a pure inductance.
The impedance diagram
Impedance is drawn on its own impedance diagram, not a phasor diagram. Resistance lies along the positive real axis, inductive reactance points straight up and capacitive reactance straight down. A passive network never has negative resistance, so its impedance always lies in the first or fourth quadrant. For R, L and C in series the reactances partly cancel:
If \(X_L > X_C\), the angle is positive and the circuit is inductive, with current lagging the source voltage. If \(X_C > X_L\), the angle is negative and the circuit is capacitive, with current leading. With net reactance X, the magnitude is \(\sqrt{R^2 + X^2}\) and the angle is \(\tan^{-1}(X/R)\).
Series ac circuits
In a series circuit the same current flows through every element, exactly as in dc. Impedances in series add as complex numbers, \(Z_T = Z_1 + Z_2 + \cdots + Z_N\), and the current is \(\mathbf{I} = \mathbf{E}/Z_T\). Each element's voltage is then \(\mathbf{V}_x = \mathbf{I}Z_x\). Kirchhoff's voltage law still holds, but as a phasor sum: \(\mathbf{E} = \mathbf{V}_1 + \mathbf{V}_2 + \cdots\). Voltmeter readings across the elements do not add up to the source reading, because the element voltages peak at different instants. The average power delivered is \(P = EI\cos\theta_T\), where \(\theta_T\) is the angle of \(Z_T\), and all of it is dissipated in the resistance, so \(P = I^2R\) as well.
Worked example: a series R-L-C circuit
A 120 V, 60 Hz source, \(\mathbf{E} = 120\angle 0^\circ\,\text{V}\), drives a 39 Ω resistor, a 0.22 H inductor and a 47 µF capacitor in series. 1. Reactances, with \(\omega = 377\) rad/s:
2. Total: \(Z_T = 39 + j26.5\,\Omega = 47.2\angle 34.2^\circ\,\Omega\), inductive. 3. Current: \(\mathbf{I} = 120\angle 0^\circ / 47.2\angle 34.2^\circ = 2.55\angle -34.2^\circ\) A. 4. Voltages:
5. Check: the three phasors sum to \(120\angle 0^\circ\) V, and \(I^2R = 253\) W equals \(EI\cos 34.2^\circ\). The inductor's 211 V exceeds the source because the capacitor's voltage partly cancels it.
Phasor diagrams and power factor
A phasor diagram shows the same results as arrows. Draw the current first; the resistor voltage lies along it, the inductor voltage 90° ahead and the capacitor voltage 90° behind. Placed head to tail, these arrows end at the tip of \(\mathbf{E}\): Kirchhoff's voltage law as a picture. The angle from \(\mathbf{I}\) to \(\mathbf{E}\) is \(\theta_T\), the impedance angle. The power factor is \(F_p = \cos\theta_T = R/|Z_T|\). It is called lagging when the current lags, in an inductive circuit, and leading when the current leads, in a capacitive one. In the worked example, \(F_p = \cos 34.2^\circ = 0.827\) lagging, which is also \(39/47.2\). A power factor near 1 means the resistance dominates the net reactance.
The voltage divider rule
You do not need the current to find one element's voltage. As in dc, the voltage across any impedance in a series string is its share of the total:
Here \(Z_x\) may be one element or several adjacent ones. The arithmetic is complex, so an element voltage can lead or lag the source and, when reactances partly cancel, exceed it in magnitude. The rule needs every impedance in the string to carry the same current, so it fails if a branch leaves the string between them.
Worked example: an R-C divider
A 10 V, 1 kHz signal, \(\mathbf{E} = 10\angle 0^\circ\,\text{V}\), feeds a 2.2 kΩ resistor in series with a 0.1 µF capacitor. Find the capacitor voltage. 1. Reactance: \(X_C = 1/(2\pi \times 1000 \times 0.1\,\mu\text{F}) = 1.59\) kΩ. 2. Total: \(Z_T = 2.2 - j1.59\,\text{k}\Omega = 2.72\angle -35.9^\circ\,\text{k}\Omega\). 3. Divider:
4. In the same way, \(\mathbf{V}_R = 8.10\angle 35.9^\circ\) V. 5. Check: the magnitudes add to 13.96 V, more than 10 V, but the two phasors are 90° apart and \(\sqrt{5.86^2 + 8.10^2} = 10.0\) V.
Common mistakes to avoid
1. Adding magnitudes: 30 Ω of resistance in series with 40 Ω of reactance is 50 Ω, not 70 Ω. 2. Dropping the capacitor's sign: \(Z_C = -jX_C\), so capacitive reactance subtracts from inductive reactance. 3. Using f where ω belongs: \(X_L = 2\pi fL\), not \(fL\). 4. Trusting a calculator's arctangent without checking the quadrant, which puts \(-50 - j30\) at 31° instead of −149°. 5. Mixing peak and rms values in one calculation: keep phasors in rms and convert only at the end. 6. Adding voltmeter readings around a loop and expecting them to equal the source reading.
Key takeaways
Impedance \(Z = \mathbf{V}/\mathbf{I}\) is a complex number of ohms, \(R + jX\), with no time function. A resistor is \(R\angle 0^\circ\), an inductor \(jX_L\) and a capacitor \(-jX_C\). Series impedances add as complex numbers and \(\mathbf{I} = \mathbf{E}/Z_T\). Kirchhoff's voltage law holds for phasors, not rms readings. A positive impedance angle means an inductive circuit with lagging current; a negative one, a capacitive circuit with leading current. Power is \(P = EI\cos\theta_T = I^2R\), and the power factor is \(\cos\theta_T = R/|Z_T|\). The voltage divider rule, \(\mathbf{V}_x = Z_x\mathbf{E}/Z_T\), finds any series voltage directly.
Flashcards
Flashcard
Z = V/I, the ratio of phasor voltage to phasor current, in ohms
Test your understanding
Question 1 of 5
A 15 Ω resistor is in series with an inductor whose reactance is 20 Ω. What is the total impedance in polar form?
Question 2 of 5
In a series R-C circuit, a voltmeter reads 30 V across the resistor and 40 V across the capacitor. What does it read across the source?
Question 3 of 5
A series circuit has R = 12 Ω, X_L = 25 Ω and X_C = 9 Ω. What is its power factor?
Question 4 of 5
A 20∠0° V source drives a 6 Ω resistor in series with an 8 Ω inductive reactance. What is the voltage across the inductor?
Question 5 of 5
What is the impedance of a 10 µF capacitor at 50 Hz?
