Electrical Engineering › Section N · Decibels, filters, and Bode plots › Topic N.2
R-C low-pass and high-pass filters
One resistor and one capacitor are enough to pass low frequencies and block high ones, or the reverse. These simple filters clean up sensor signals, remove hum and set the bandwidth of countless circuits, and their behaviour follows from a single cutoff frequency.
What a filter does
A filter is a network built to pass some frequencies and reject others. A low-pass filter passes frequencies below a critical value and attenuates those above it; a high-pass filter does the opposite. Pass-band filters pass a range between two critical frequencies, and stop-band filters reject such a range. Passive filters use only R, L and C; active filters add transistors or op-amps. By convention the pass-band is where the output is at least 0.707 of its maximum, the −3 dB level from the topic Logarithms and decibels, the same level used for the bandwidth of resonant circuits.
The R-C low-pass circuit
Connect the source \(V_i\) between node a and ground (node 0). Place R from node a to node b, and C from node b to ground; the output \(V_o\) is taken across the capacitor, from b to 0. At very low frequencies the reactance \(X_C = \frac{1}{2\pi fC}\) is huge, the capacitor acts almost as an open circuit, no current flows through R, and \(V_o \approx V_i\). At very high frequencies \(X_C\) is tiny, the capacitor acts almost as a short, and \(V_o \approx 0\). Somewhere between, the output changes from passing to blocking. The topic Frequency response of the R-C circuit traced this same behaviour for the capacitor voltage.
The transfer ratio and the cutoff frequency
Divide the output phasor by the input phasor to get the normalised gain \(\mathbf{A}_v = \mathbf{V}_o/\mathbf{V}_i\), a dimensionless ratio whose magnitude here is at most 1. By the voltage divider rule, \(\mathbf{A}_v = \frac{-jX_C}{R - jX_C}\). The transition is placed where \(R = X_C\), which gives the cutoff frequency
In terms of \(f/f_c\), the magnitude and phase are
At \(f = f_c\), \(|A_v| = 0.707\), or −3.01 dB, the output power is half its maximum, and \(V_o\) lags \(V_i\) by 45°. Because the output always lags, this is called a lagging network.
Beyond the cutoff
The table gives the low-pass response at a few ratios of \(f/f_c\) (magnitude, gain in dB, phase):
Well above cutoff, \(|A_v| \approx f_c/f\): each tenfold rise in frequency cuts the output by another factor of 10, or 20 dB, and the phase approaches −90°. Well below cutoff the output is almost exactly the input. Bode plots, two topics on, turn these facts into straight-line sketches.
Worked example: a low-pass filter
A filter has R = 4.7 kΩ in series and C = 10 nF across the output, driven by 2.0 V rms. Find \(f_c\) and the output at 1 kHz and 10 kHz. 1. Cutoff: \(f_c = \frac{1}{2\pi(4700)(10 \times 10^{-9})} = 3.39\,\text{kHz}\). 2. At 1 kHz, \(f/f_c = 0.295\), so \(|A_v| = 1/\sqrt{1 + 0.295^2} = 0.959\), which is −0.36 dB, with \(\theta = -16.5^\circ\). The output is \(0.959 \times 2.0 = 1.92\,\text{V}\) rms. 3. At 10 kHz, \(f/f_c = 2.95\), so \(|A_v| = 0.321\), which is −9.88 dB, with \(\theta = -71.3^\circ\); the output is 0.641 V rms. 4. Check: 1 kHz is in the pass-band, so the output is close to 2 V; 10 kHz is about three times \(f_c\), so the output is roughly a third of the input.
The R-C high-pass circuit
Swap the two parts: C now runs from node a to node b, R from node b to ground, and \(V_o\) is taken across R. At low frequencies the capacitor is almost an open circuit, so \(V_o \approx 0\); in particular, dc is blocked completely. At high frequencies the capacitor is almost a short, so \(V_o \approx V_i\). The cutoff is again where \(R = X_C\), at the same \(f_c = \frac{1}{2\pi RC}\), and
The output leads the input, by 45° at cutoff and towards 90° far below it, so this is a leading network. Below cutoff the output falls by 20 dB per decade as the frequency decreases.
Worked example: removing mains hum
An audio input has R = 10 kΩ to ground, and a series capacitor is to make a high-pass filter with \(f_c\) near 100 Hz to reduce 60 Hz hum. Choose C and find the attenuation at 60 Hz and 1 kHz. 1. Rearrange: \(C = \frac{1}{2\pi R f_c} = \frac{1}{2\pi(10^4)(100)} = 159\,\text{nF}\). 2. Nearest standard value: 150 nF, giving \(f_c = \frac{1}{2\pi(10^4)(150 \times 10^{-9})} = 106\,\text{Hz}\). 3. At 60 Hz, \(f_c/f = 1.77\), so \(|A_v| = 0.492\), or −6.16 dB, with the output leading by 60.5°. 4. At 1 kHz, \(f_c/f = 0.106\), so \(|A_v| = 0.994\), or −0.05 dB. 5. Check: hum is cut to about half its voltage while speech-band signals pass almost untouched; a steeper filter would be needed to remove hum fully.
R-L versions and choosing a filter
An inductor can do the same jobs, because \(X_L = 2\pi fL\) rises with frequency. With L in series and the output across R, the network is a low-pass filter; with R in series and the output across L, it is high-pass. In both cases the cutoff is where \(R = X_L\), at \(f_c = \frac{R}{2\pi L}\); for example, R = 1 kΩ with L = 10 mH gives 15.9 kHz. At low frequencies capacitors are smaller, cheaper and closer to ideal than inductors, so R-C filters are far more common. Whichever is used, the formulas hold only when the load across the output draws negligible current; a heavy load changes the cutoff.
Common mistakes to avoid
First, writing \(f_c = 1/(RC)\): that is the cutoff as an angular frequency in rad/s, and the cutoff in hertz needs the \(2\pi\). Second, swapping the output node: across C gives low-pass, across R gives high-pass. Third, thinking the output stops at cutoff: at \(f_c\) it is still 70.7% of the input, and the fall continues gradually. Fourth, giving a low-pass filter a leading phase: its output lags, and the high-pass output leads. Fifth, ignoring the load: a resistor across the output appears in parallel with an element and shifts \(f_c\).
Key takeaways
Filters are low-pass, high-pass, pass-band or stop-band; the pass-band edge is the 0.707, or −3 dB, level. For an R-C filter, the cutoff is where R = X_C, at f_c = 1/(2πRC). Low-pass: output across C, |A_v| = 1/√(1 + (f/f_c)²), lagging by up to 90°, 45° at cutoff. High-pass: output across R, |A_v| = 1/√(1 + (f_c/f)²), leading by up to 90°, and dc is blocked. Far into the stop-band the output falls by 20 dB per decade. R-L filters work the same way with f_c = R/(2πL). Output loading shifts the cutoff.
Flashcards
Flashcard
A network designed to pass some frequencies and reject others
Test your understanding
Question 1 of 5
A low-pass filter has R = 2.2 kΩ in series and C = 47 nF across the output. What is its cutoff frequency?
Question 2 of 5
An R-C low-pass filter is driven at exactly its cutoff frequency. How does the output compare with the input?
Question 3 of 5
In an R-C high-pass filter, where is the output taken, and what happens to a dc input?
Question 4 of 5
A low-pass filter has f_c = 2 kHz. Roughly what is its gain at 20 kHz?
Question 5 of 5
A high-pass filter uses R = 10 kΩ and C = 150 nF. What is its normalised gain at 60 Hz?
