Electrical Engineering › Section L · Power (ac) and resonance › Topic L.1

Resistive, inductive, and capacitive power

In an ac circuit some energy is used up and some only borrows the wiring for a moment and goes back to the source. Real, reactive and apparent power separate the two, and they explain why equipment is rated in volt-amperes rather than watts.

Power that comes back

In a dc circuit the power is simply \(VI\). In an ac circuit the current can be out of step with the voltage, and then the product \(v(t)\,i(t)\) dips below zero for part of every cycle: the load is handing energy back to the source. Engineers therefore use three powers: real (average) power \(P\) in watts (W), the energy actually turned into heat, light or work each second; reactive power \(Q\) in volt-amperes reactive (VAR), energy that only shuttles back and forth; and apparent power \(S\) in volt-amperes (VA), the plain product of rms voltage and rms current. Throughout, \(V\) and \(I\) are rms values, and the passive sign convention holds, so a positive \(p\) means the element is absorbing power.

Instantaneous power for any load

Let the voltage lead the current by an angle \(\theta\): \(v = \sqrt{2}\,V\sin(\omega t + \theta)\) and \(i = \sqrt{2}\,I\sin\omega t\). Multiplying and using trigonometric identities gives

\begin{aligned} p &= VI\cos\theta\,(1 - \cos 2\omega t) \\ &\quad + VI\sin\theta\,\sin 2\omega t \end{aligned}

Both terms oscillate at twice the supply frequency, so a 60 Hz supply gives a 120 Hz power wave. The first term is never negative and averages \(VI\cos\theta\). The second averages zero; its peak, \(VI\sin\theta\), is the reactive power. An equivalent form, \(p = VI[\cos\theta - \cos(2\omega t + \theta)]\), shows that \(p\) swings between \(VI(\cos\theta - 1)\) and \(VI(\cos\theta + 1)\), and is negative for a fraction \(|\theta|/180^\circ\) of each cycle.

The resistor: all real power

For a resistor, voltage and current are in phase, so \(\theta = 0\) and

p_R = VI(1 - \cos 2\omega t)

The curve rises from 0 to \(2VI\) and back, never dipping below zero: every joule delivered is converted to heat, and none returns. Its average is the real power, \(P = VI = I^2R = V^2/R\). Over one cycle of the supply, of period \(T = 1/f\), the energy dissipated is \(W = PT = P/f\). A 1500 W heater on 120 V, for instance, draws 12.5 A, has a resistance of 9.6 Ω, and turns 25 J into heat in every \(1/60\) s cycle.

Apparent power and kVA ratings

Apparent power is \(S = VI\), and since \(V = IZ\) it can also be written \(S = I^2Z = V^2/Z\). Real power is \(P = S\cos\theta\), so the power factor \(F_p = \cos\theta = P/S\), met in the topic "Frequency response, average power, and power factor", is the share of the apparent power that is real. Only a purely resistive load has \(P = S\). Transformers, generators and cables are rated in VA or kVA because what overheats them is current, whatever the power factor. A transformer rated 10 kVA at 240 V may carry \(10\,000/240 = 41.7\) A. A nearly pure inductor drawing that current would barely move a wattmeter, yet load the windings fully.

The inductor: reactive power

For an ideal inductor the voltage leads the current by \(90^\circ\), so

p_L = VI\sin 2\omega t

There is no constant term, so the average power is zero. In each positive half of the power wave the inductor absorbs energy to build its magnetic field; in the next it returns exactly the same amount. The peak of this swing is its reactive power:

Q_L = VI = I^2X_L = \frac{V^2}{X_L}

With \(P = 0\) and \(S = VI\), the power factor is 0. The stored energy rises from zero to \(\tfrac{1}{2}L\,i_{\text{peak}}^2 = LI^2\) (with \(I\) in rms) and falls back, twice in every supply cycle.

The capacitor: reactive power of opposite sign

For an ideal capacitor the current leads the voltage by \(90^\circ\), so \(\theta = -90^\circ\) and \(p_C = -VI\sin 2\omega t\). Again the average is zero, and the reactive power is negative, \(Q_C = -VI = -I^2X_C\), or \(-V^2/X_C\). The stored energy peaks at \(\tfrac{1}{2}C\,v_{\text{peak}}^2 = CV^2\). The minus sign matters: with \(Q = VI\sin\theta\), inductive reactive power is positive and capacitive reactive power negative. When an inductor and a capacitor share a current or a voltage, one absorbs energy while the other releases it, so their reactive powers partly cancel, the basis of the power triangle and of power-factor correction.

Worked example: one load, three powers

A load on 120 V draws 5.0 A, and the current lags the voltage by \(30^\circ\). Find \(P\), \(Q\), \(S\) and the range of \(p\). 1. Current lagging means voltage leading, so \(\theta = +30^\circ\): the load is inductive. 2. \(S = VI = 120 \times 5.0 = 600\) VA. 3. \(P = S\cos 30^\circ = 520\) W. 4. \(Q = S\sin 30^\circ = +300\) VAR, positive because inductive. 5. \(p\) swings from \(600(0.866 - 1) = -80.4\) W up to \(600(0.866 + 1) = 1120\) W, and is negative for \(30/180 = 1/6\) of each cycle. 6. Check: \(F_p = 520/600 = 0.866\) lagging, which is \(\cos 30^\circ\), as it should be.

Worked example: an inductor and a capacitor on the mains

A 100 mH inductor is connected to 120 V at 60 Hz. 1. \(X_L = 2\pi fL = 2\pi(60)(0.100) = 37.7\,\Omega\). 2. \(I = V/X_L = 120/37.7 = 3.18\) A. 3. \(Q_L = VI = 120 \times 3.183 = 382\) VAR; check with \(V^2/X_L = 14\,400/37.7 = 382\) VAR. 4. \(P = 0\) W, \(S = 382\) VA and \(F_p = 0\). 5. Peak stored energy: \(LI^2 = 0.100 \times 3.18^2 = 1.01\) J. Now a 22 µF capacitor on the same supply: 6. \(X_C = 1/(2\pi fC) = 121\,\Omega\), so \(I = 0.995\) A and \(Q_C = -119\) VAR, with peak stored energy \(CV^2 = 0.317\) J. Both draw real current from the supply, yet neither uses any energy on average.

Why reactive power matters

If an ideal inductor uses no energy, why care? Because the source must still deliver the current that carries the borrowed energy out and back. That current heats every conductor on the way (\(I^2R\) losses), takes up generator and transformer capacity, and causes voltage drops. Two loads using the same real power can draw very different currents if their reactive powers differ, which is why utilities watch reactive power closely.

Common mistakes to avoid

First, calling \(VI\) the power in watts: it is the apparent power, and equals the real power only when \(\theta = 0\). Second, thinking reactive power is energy wasted in the inductor or capacitor: ideal reactive elements dissipate nothing; the cost is the extra current in the wiring. Third, mixing peak and rms values: \(P = VI\cos\theta\) uses rms values, and with peak values it becomes \(\tfrac{1}{2}V_pI_p\cos\theta\). Fourth, getting the sign of \(\theta\) backwards: \(\theta\) is the angle by which voltage leads current, so a lagging current means positive \(\theta\) and positive \(Q\). Fifth, expecting the power wave at the supply frequency: it runs at twice that frequency.

Key takeaways

For any load, \(p\) pulses at twice the supply frequency: an average part \(VI\cos\theta\) plus a part with zero average and peak \(VI\sin\theta\). Real power \(P = VI\cos\theta\) (W) is energy converted; reactive power \(Q = VI\sin\theta\) (VAR) is energy exchanged; apparent power \(S = VI\) (VA) sets the current and the equipment rating, and \(F_p = P/S\). A resistor has \(P = I^2R\) and \(Q = 0\). An inductor has \(P = 0\) and \(Q_L = I^2X_L\), positive. A capacitor has \(P = 0\) and \(Q_C = -I^2X_C\), negative. Peak stored energies are \(LI^2\) and \(CV^2\) with rms values.

Flashcards

Flashcard

Real power P

Average power, P = VI cos θ, in watts (W)

The energy per second actually converted to heat, light or work.

Test your understanding

Question 1 of 5

A 240 V load draws 8.0 A rms, and the current lags the voltage by 60°. What real power does it absorb?

Question 2 of 5

A 47 µF capacitor is connected to 120 V rms at 60 Hz. What is the size of its reactive power?

Question 3 of 5

What is the average power absorbed by an ideal inductor over a whole cycle?

Question 4 of 5

A transformer is rated 25 kVA at 240 V. It feeds a motor load with a power factor of 0.8 lagging. What is the most current it can deliver within its rating?

Question 5 of 5

A resistor is connected to a 60 Hz supply. How does its instantaneous power behave?

← Previous topicNext topic →