Electrical Engineering › Section Q · Thyristors, operational amplifiers, and power conversion › Topic Q.2
The SCR, the TRIAC, and optothyristors
Give a Shockley diode a third terminal and a tiny gate pulse can decide exactly when it fires. That one change turns a curiosity into the workhorse of dimmers, heater controls, motor drives and controlled rectifiers.
A Shockley diode with a gate
The silicon-controlled rectifier, or SCR, is the PNPN structure of Hysteresis, gas discharge tubes, the Shockley diode, and the DIAC with one more lead, the gate, joined to the base of the internal NPN transistor. With the gate unconnected it behaves like a Shockley diode, fired by breakover or a fast dv/dt. The gate adds a deliberate third way. Make the gate positive with respect to the cathode, so a small conventional current flows into the gate and out of the cathode, and the NPN transistor turns on, feeds the PNP, and the pair latch. A few milliamps at the gate can switch amperes at the anode.
Triggering, holding and turning off
Gate triggering is the normal way to fire an SCR, so parts are chosen with a breakover voltage well above anything the supply will produce. Once latched, the gate loses control. The anode current must reach the latching current to stay on after the trigger ends, and the SCR then conducts until the current falls below the holding current, typically 1 mA to 50 mA. On ac this happens at every current zero: natural commutation. Pulling the gate negative rarely turns a plain SCR off. A gate turn-off thyristor (GTO) is built to do it, but needs a reverse gate current of often a fifth or more of the anode current.
Meter checks and a test circuit
The only PN junction between two terminals is gate to cathode, so a diode-test meter shows a junction reading with the positive lead on the gate and the common lead on the cathode, and open circuit for every other pair. Larger SCRs often contain a gate-to-cathode resistor against noise triggering, and read low both ways; parts without it are sensitive-gate SCRs. A meter check proves little, so test under load: a dc supply and load, a normally open button that briefly feeds the gate from the anode side, and a normally closed button that breaks the current. If the load draws less than the holding current, a good SCR will not stay on.
SCRs in dc circuits
The test circuit is already a start-stop control for a dc lamp or motor. A more important dc job is the crowbar: an SCR across the output of a dc power supply, with a fuse or current-limiting resistance ahead of it. A sensing circuit watches the output, and if the voltage rises too high it triggers the SCR, which short-circuits the output and blows the fuse before the excess voltage can damage the load, like dropping a steel bar across the terminals.
Phase control on ac
Most SCRs control ac power. Fired at an angle \(\alpha\) after the source voltage crosses zero, an SCR conducts for the rest of that positive half-cycle, a conduction angle of \(180^\circ - \alpha\), and is off in the negative half-cycle. Changing \(\alpha\) chops the half-sine to deliver more or less power. For a resistive load and source peak \(V_m\), the average load voltage is
It is \(V_m/\pi\) at \(\alpha = 0^\circ\) and zero at \(\alpha = 180^\circ\). Mains phase-control circuits are dangerous: they are built and tested with isolation and qualified supervision, never worked on live.
Worked example: a half-wave heater control
An SCR controls a 24 Ω heater from a 120 V rms, 60 Hz supply and is fired at \(\alpha = 90^\circ\). 1. Peak: \(V_m = 120\sqrt{2} = 169.7\,\text{V}\). 2. Average load voltage: \(V_{avg} = \frac{169.7}{2\pi}(1 + 0) = 27.0\,\text{V}\). 3. Power with \(\alpha = 0^\circ\) (half-wave): one half-cycle of the full 600 W, so 300 W. 4. At \(90^\circ\) the SCR passes the second quarter of each positive half-cycle, which carries the same energy as the first by symmetry, so \(P = 150\,\text{W}\). 5. Delay: \(90^\circ\) is a quarter of a 16.7 ms period, 4.17 ms after each zero. Check: half the conduction time at full voltage gives half the power.
Worked example: a resistive gate trigger
Feed the gate from the anode side through a diode (0.7 V) and a resistor \(R_G = 22\,\text{k}\Omega\). Assume the SCR needs 5 mA at a gate voltage of 0.8 V, and the 120 V rms supply. 1. Firing level:
The load's drop at 5 mA is negligible. 2. Angle: \(\sin\alpha = 111.5/169.7\), so \(\alpha = 41.1^\circ\). 3. Limit: the latest firing is at the peak, \(90^\circ\), reached with \(R_G = (169.7 - 1.5)/0.005 = 33.6\,\text{k}\Omega\). Any larger and the SCR never fires. Check: a larger \(R_G\) needs a higher voltage, so the angle grows, but only up to \(90^\circ\).
Beyond the peak, and bridges
To fire later than \(90^\circ\), add a capacitor so the gate circuit sees an RC-delayed voltage that lags the source by up to nearly \(90^\circ\) and is still rising after the source peaks. Larger controls use dedicated trigger circuits. Replacing the diodes of a bridge rectifier with SCRs gives a controlled rectifier whose dc output follows the firing angle; single-phase and three-phase versions are common in industry, and banks of thyristors convert power in high-voltage dc links. Because the SCRs in a bridge do not all share a cathode, each gate is driven through a pulse transformer, which also isolates the trigger circuit from the power circuit.
The TRIAC
A TRIAC acts like two SCRs in inverse parallel, made in one piece of silicon, so it conducts in both half-cycles. Its terminals are main terminal 1 (MT1), main terminal 2 (MT2) and the gate. They are not interchangeable: the gate is driven relative to MT1, with trigger current taken from the MT2 side, and data sheets name the pins. TRIACs often fire at slightly different points in the two half-cycles, and an asymmetric waveform contains even harmonics (see Fourier series and nonsinusoidal circuits). A DIAC in series with the gate, breaking over at nearly equal voltages both ways, makes firing symmetric. TRIACs suit lamp dimmers and small loads; high-power controls favour SCR pairs.
Optothyristors
SCRs and TRIACs can also be triggered by light instead of gate current. A light-activated SCR is called a LASCR; the light-triggered TRIAC is simply an opto-TRIAC. Their main use is inside sealed optoisolators, where an LED and the optothyristor face each other with only clear insulation between them. A low-voltage logic circuit lights the LED, and the optothyristor switches a mains-side circuit, often the gate of a larger TRIAC, with no electrical connection between the two sides. That isolation protects both the control electronics and the people using them.
Common mistakes to avoid
First, expecting the gate to turn a latched SCR off: removing the gate signal does nothing, and only a GTO is designed for gate turn-off. Second, using the rms voltage to find a firing angle: compare the trigger level with the peak, \(\sqrt{2}\) times the rms. Third, thinking a resistive gate network can delay firing past \(90^\circ\): that needs a phase-shifting capacitor. Fourth, swapping MT1 and MT2 on a TRIAC. Fifth, blaming the SCR when a high-resistance load fails to latch: the load current may be below the holding current.
Key takeaways
An SCR is a Shockley diode with a gate; positive gate current relative to the cathode fires it, and it stays on until its current falls below the holding current. A GTO can be turned off from its gate, at the cost of a large reverse gate current. Phase control fires at an angle α, giving V_avg = (V_m/2π)(1 + cos α) for a half-wave resistive load; a resistive trigger reaches only 90°, an RC network goes further. Crowbars protect dc supplies. A TRIAC conducts both ways, with a DIAC for symmetric firing, and optothyristors isolate logic from mains.
Flashcards
Flashcard
Silicon-controlled rectifier: a PNPN thyristor with a gate joined to the internal NPN base
Test your understanding
Question 1 of 5
An SCR feeds a resistive load from a 120 V rms supply (half-wave control) and is fired at 60 degrees. What is the average load voltage?
Question 2 of 5
A gate trigger network (diode 0.7 V, R_G = 22 kilohms) fires an SCR needing 5 mA at 0.8 V from a 120 V rms supply. At about what angle does it fire?
Question 3 of 5
Why is a DIAC often placed in series with the gate of a TRIAC in a lamp dimmer?
Question 4 of 5
A diode-test meter is used on a small SCR with no internal gate resistor. Which pair of terminals shows a junction reading?
Question 5 of 5
In a 12 V dc test circuit, an SCR with a 1.0 V on-state drop and a holding current of 20 mA drives a 680 ohm load. It turns on when the gate is triggered but goes off as soon as the trigger ends. Why?
