Electrical Engineering › Section Q · Thyristors, operational amplifiers, and power conversion › Topic Q.1
Hysteresis, gas discharge tubes, the Shockley diode, and the DIAC
Thyristors are semiconductor switches that stay on once fired and stay off once stopped. This topic builds the idea from glowing gas to the four-layer Shockley diode and its two-way cousin, the DIAC, which triggers the power switches of the next topic.
Switches that remember
A toggle switch stays where you flip it after you let go; a momentary pushbutton springs back. The toggle shows hysteresis: once a cause has changed its state, the system does not return when the cause is removed. BJTs, JFETs and MOSFETs have no such memory: their output follows their input along a characteristic curve, which is what lets them amplify. Thyristors are different. A brief event latches them on, and they stay on until something stops them. That makes them excellent power switches but useless as linear amplifiers.
Positive feedback makes a latch
How can a latching device be built from transistors that do not latch? With positive feedback, also called regenerative feedback. Negative feedback, met in Feedback, amplifier impedances, current mirrors, ratings, and quirks, opposes the input and steadies an amplifier. Positive feedback reinforces it: more output produces more input, which produces more output, until the device saturates. In reverse, less output produces less input until the device cuts off. Either way it races to an extreme and stays there, the on-or-off memory a thyristor needs.
Gas that strikes and extinguishes
Gas shows the same behaviour. Air or neon is normally an excellent insulator, but a high enough voltage tears electrons from atoms; the gas becomes ionised, a plasma, and conducts well. The discharge keeps itself going even after the voltage falls well below the level that started it, and stops only when the voltage is too low to sustain it. A neon lamp therefore has a higher striking voltage and a lower extinguishing voltage. Lightning is the large-scale version: charge builds slowly, the air breaks down in a sudden bolt, then recovers.
Worked example: a neon relaxation oscillator
A 100 V dc supply charges a 0.1 µF capacitor through 1.0 MΩ, with a neon lamp across the capacitor. Assume the lamp strikes at 80 V, extinguishes at 60 V, and discharges the capacitor almost instantly. 1. Time constant: \(\tau = RC = 0.10\,\text{s}\). 2. From Charging and discharging transients, the time to charge from \(V_1\) to \(V_2\) towards \(E\) is
3. Each cycle runs from 60 V to 80 V: \(t = 0.10\ln(40/20) = 69.3\,\text{ms}\), about 14.4 flashes per second. 4. The first cycle starts from 0 V, so it is longer: \(0.10\ln(100/20) = 161\,\text{ms}\). 5. Check: 69.3 ms is less than one time constant, sensible for a swing of only 20 V.
The thyratron, ancestor of the thyristor
A circuit that slowly charges a capacitor and then suddenly dumps it through a hysteretic device is a relaxation oscillator; its output is far from sinusoidal. Adding a control grid to a gas-filled tube gave the thyratron. A small grid voltage decided when the tube struck, and it then conducted until the plate voltage fell to nearly zero. On ac that happens every half-cycle, so the tube switched itself off and waited for the next trigger. Semiconductors have replaced thyratrons almost everywhere, and the word thyristor echoes the older name.
The Shockley diode: four layers, two transistors
The Shockley diode, also called the four-layer or PNPN diode, is named after William Shockley, one of the transistor's inventors; do not confuse it with the Schottky diode. It is a P-N-P-N sandwich with an anode on the outer P layer and a cathode on the outer N layer. Split the middle layers in your mind and it becomes a PNP and an NPN transistor, each collector driving the other's base, as described in Inside BJTs, JFETs, MOSFETs, and thyristors. Conventional current enters the anode and leaves the cathode. Each transistor waits for base current that only its partner can supply, so with modest voltage applied both sit in cutoff.
Breakover, latching and dropout
Raise the anode-to-cathode voltage and almost no current flows until the breakover voltage \(V_{BO}\) is reached. Then one junction begins to conduct, which feeds base current to the other transistor, which feeds the first: regeneration drives both into saturation. The device is now latched, and its voltage collapses to about a volt. Firing is the word for starting this state. Lowering the voltage below \(V_{BO}\) does not turn it off. Only when the current falls below the holding current \(I_H\) can the transistors no longer keep each other saturated, and the device drops out. Plotted as current against voltage, the rising and falling paths differ: a hysteresis loop.
Worked example: a Shockley diode on a variable supply
A Shockley diode is in series with a 1.0 kΩ resistor across an adjustable dc supply. Take \(V_{BO} = 20\,\text{V}\), an on-state drop of 1.0 V and \(I_H = 5\,\text{mA}\) (assumed values). 1. Off, the current is tiny, so nearly the whole supply appears across the diode: it fires when the supply reaches 20 V. 2. Latched at 20 V: \(I = (20 - 1.0)/1000 = 19\,\text{mA}\). 3. Turn the supply down to 12 V: still latched, \(I = 11\,\text{mA}\). 4. Dropout when \(I < I_H\): \(E < 1.0 + (0.005)(1000) = 6.0\,\text{V}\). 5. Check: between 6 V and 20 V the diode can be on or off, depending on its history.
False firing from fast voltage rise
There is a second, usually unwanted, way to fire a thyristor. Its junctions have small capacitances, and a capacitor draws current \(i = C\,dv/dt\). If the anode voltage rises very quickly, that charging current can act as base current and latch the device well below \(V_{BO}\). Data sheets give the limit as the critical rate of voltage rise, in volts per microsecond. Designers protect against it with a series inductor, which slows current changes, or with a snubber: a resistor and capacitor in series, placed across the thyristor so that fast voltage edges are absorbed.
The DIAC on alternating current
Two Shockley diodes in inverse parallel make the DIAC, which breaks over in either polarity, typically at about 30 V. On ac it drops out each time the current passes through zero and must break over again. With a 24 V rms supply (peak 33.9 V) feeding a resistive load through a 30 V DIAC, it fires when \(33.9\sin\theta = 30\), at \(\theta = 62.1^\circ\) into each half-cycle of either polarity, and conducts until near the next zero. If the peak never reaches \(V_{BO}\), it never fires. A real DIAC's voltage snaps back only a few volts, not to one volt; its main job is triggering TRIACs.
Common mistakes to avoid
First, thinking a latched thyristor turns off when the voltage falls below breakover: it stays on until its current falls below the holding current. Second, comparing an rms value with a breakover voltage: use the peak, \(\sqrt{2}\) times the rms. Third, calling the Shockley diode a Schottky diode. Fourth, using \(RC\ln(E/(E - V_2))\) for every relaxation cycle: only the first starts from 0 V; later ones start from the extinguishing voltage. Fifth, ignoring dv/dt: a fast edge can fire a thyristor that never saw its breakover voltage.
Key takeaways
Hysteresis is memory of state; thyristors get it from positive feedback between a PNP and an NPN transistor. Ionised gas strikes at one voltage and extinguishes at a lower one, the basis of neon relaxation oscillators and the thyratron. A Shockley diode fires at its breakover voltage, latches with about a volt across it, and drops out only below its holding current; a fast dv/dt can also fire it, so snubbers are used. A DIAC breaks over in either polarity, about 30 V, and drops out at each current zero.
Flashcards
Flashcard
A system does not return to its earlier state when the cause of a change is removed
Test your understanding
Question 1 of 5
A latched Shockley diode (breakover 20 V, on-state drop 1.0 V, holding current 10 mA) is in series with 470 ohms across a dc supply. As the supply is turned down, below what supply voltage does the diode turn off?
Question 2 of 5
A DIAC that breaks over at 32 V is placed in series with a resistive load across a 30 V rms supply. At what angle into each half-cycle does it fire?
Question 3 of 5
Which action turns off a Shockley diode that is latched on in a dc circuit?
Question 4 of 5
A thyristor fires even though the applied voltage never reached its breakover voltage. Which is the most likely cause?
Question 5 of 5
A 90 V dc supply charges 0.22 µF through 470 kilohms, with a neon lamp across the capacitor that strikes at 70 V and extinguishes at 50 V. Ignoring discharge time, how long is each cycle after the first?
