Physics › Section N · Electric potential and capacitance › Topic N.4
Capacitors and dielectrics
A capacitor holds separated charge ready to be released in an instant, which is how a camera flash fires and a phone screen senses your finger. How much it holds depends on the voltage applied, the size and spacing of its plates, and the insulator between them.
Two conductors, kept apart
A capacitor is two conductors placed close together but not touching, usually with an insulator between them. Connect it to a battery and charge is moved from one conductor to the other: one plate ends up with charge \(+Q\) and the other with \(-Q\). The capacitor as a whole stays neutral, but we say it stores a charge \(Q\), meaning the size of the charge on either plate. Capacitors appear in almost every circuit: they smooth power supplies, filter signals, store energy for camera flashes and defibrillators, and sense touch in phone screens.
Charge is proportional to voltage
For a parallel-plate capacitor, more charge on the plates means more field lines between them, so \(E\) is proportional to \(Q\). Since \(V = Ed\) for the uniform field between the plates, \(V\) is proportional to \(Q\) too. The same proportion holds for capacitors of any shape, and its constant is the capacitance \(C\):
Capacitance is the charge stored per volt. It depends only on the capacitor's construction, its size, shape, spacing and insulator, and not on how much charge it happens to hold: double the voltage and the charge doubles, leaving \(C\) unchanged.
The farad
Capacitance is measured in farads, F, honouring Michael Faraday: \(1\ \text{F} = 1\ \text{C/V}\). A farad is enormous, because a coulomb is a huge amount of separated charge. Everyday capacitors range from picofarads, \(1\ \text{pF} = 10^{-12}\) F, through nanofarads and microfarads, \(1\ \mu\text{F} = 10^{-6}\) F, to a few millifarads. Special supercapacitors, built with very thin layers and huge internal surface areas, reach hundreds of farads or more, but each cell works at only a few volts.
The parallel-plate capacitor
Two flat plates, each of area \(A\), separated by a small gap \(d\) of vacuum or air, have capacitance
where \(\varepsilon_0 = 8.85 \times 10^{-12}\) F/m is the permittivity of free space, also written \(\text{C}^2/(\text{N}\cdot\text{m}^2)\). Larger plates let the charge spread out, so more fits for the same voltage. A smaller gap means a smaller voltage \(V = Ed\) for the same field and charge, so again more charge per volt. The formula assumes the gap is small compared with the plates, so the field is uniform and edge effects can be ignored.
Worked example: a home-made capacitor
Two square metal sheets 20.0 cm on a side are held 0.500 mm apart in air. Find the capacitance and the charge stored at 50.0 V. 1. Area: \(A = (0.200\ \text{m})^2 = 0.0400\ \text{m}^2\), and \(d = 5.00 \times 10^{-4}\) m. 2. Capacitance:
or 708 pF. 3. Charge: \(Q = CV = (7.08 \times 10^{-10})(50.0) = 3.54 \times 10^{-8}\) C, or 35.4 nC. 4. Check the scale: for 1 F at this spacing, the area would be \(Cd/\varepsilon_0 = 5.65 \times 10^7\ \text{m}^2\), about 56 square kilometres, which shows why a farad is so large.
Dielectrics
Filling the gap with an insulator, called a dielectric, increases the capacitance by a factor \(\kappa\) (kappa), the dielectric constant of the material:
For a vacuum \(\kappa = 1\) exactly, and for air it is about 1.0006, so air capacitors behave almost like vacuum ones. Typical values are about 2.1 for Teflon, roughly 4 to 10 for glasses and about 80 for water at room temperature. A dielectric also keeps the plates apart mechanically, so they can be made very close, and in rolled capacitors two long foil strips are wound up with a thin dielectric film between them.
How a dielectric works
The field between charged plates polarises the molecules of the dielectric: their charges shift slightly, negative ends towards the positive plate and positive ends towards the negative plate. Polar molecules such as water, which already have separated charge, line up strongly, which is why water's \(\kappa\) is so large. Inside the material these shifts cancel, but they leave a thin layer of negative charge on the face next to the positive plate and positive charge on the other face. These surface charges partly cancel the field of the plates, so for the same \(Q\), \(E\) is smaller by the factor \(\kappa\). Then \(V = Ed\) is smaller, and \(C = Q/V\) is larger.
Dielectric strength
Every insulator breaks down and conducts if the field in it is too strong. The largest field a material can withstand is its dielectric strength. For dry air it is about \(3 \times 10^6\) V/m, as the previous topics showed, and some plastics, such as Teflon, withstand ten times that or more. This limits the working voltage of a capacitor, \(V_{\max} = E_{\max} d\). A good dielectric therefore helps in three ways: it raises \(C\) by the factor \(\kappa\), it lets the plates sit very close without touching, and it tolerates a larger field than air, so more charge can be stored before breakdown.
Worked example: inserting a dielectric
The 708 pF air capacitor above, charged to 50.0 V, holds 35.4 nC. A plastic sheet with \(\kappa = 3.0\) is slid in to fill the gap. Find the charge and voltage (a) if the battery stays connected and (b) if it is disconnected first. 1. New capacitance: \(C = 3.0 \times 708\ \text{pF} = 2.12 \times 10^{-9}\) F. 2. (a) The battery holds \(V = 50.0\) V, so \(Q = CV = 1.06 \times 10^{-7}\) C: the battery pushes on extra charge until the total is three times the original. 3. (b) Isolated plates keep \(Q = 35.4\) nC, so \(V = Q/C = 50.0 / 3.0 = 16.7\) V. 4. Check: in both cases \(Q/V\) has risen by the factor 3.0, as it must.
Common mistakes to avoid
First, thinking a capacitor's net charge is \(Q\): the plates carry \(+Q\) and \(-Q\), so the total is zero. Second, believing capacitance changes with voltage; it is set by construction alone. Third, leaving the gap in millimetres or the area in square centimetres in \(\varepsilon_0 A/d\). Fourth, forgetting the prefixes: pF, nF and μF differ by factors of 1000. Fifth, assuming a dielectric always raises the charge: that happens only if the battery stays connected; an isolated capacitor keeps its charge and its voltage falls.
Key takeaways
A capacitor is two conductors separated by an insulator, holding +Q and −Q. Its capacitance is C = Q/V, in farads (1 F = 1 C/V), and depends only on its construction. For parallel plates, C = ε₀A/d with ε₀ = 8.85 × 10⁻¹² F/m. A dielectric multiplies C by its dielectric constant κ, because its polarised molecules weaken the field for the same charge. Dielectric strength is the largest field a material can take, about 3 × 10⁶ V/m for dry air, and it limits the voltage: V(max) = E(max)d.
Flashcards
Flashcard
Two conductors separated by an insulator, storing +Q and −Q
Test your understanding
Question 1 of 5
A 47.0 μF capacitor is connected to a 9.00 V battery. How much charge does it store?
Question 2 of 5
A parallel-plate capacitor has plates of area 0.0100 m² separated by 1.00 mm of air. What is its capacitance?
Question 3 of 5
The plate separation of an air-filled parallel-plate capacitor is doubled. What happens to its capacitance?
Question 4 of 5
A capacitor stays connected to a battery while a dielectric with κ = 3.0 is slid in to fill the gap. What happens to the charge on its plates?
Question 5 of 5
Why does a dielectric increase a capacitor's capacitance?
