Physics › Section D · Circular motion and gravitation › Topic D.2
Centripetal force
Anything moving in a circle needs a push or pull towards the centre. Finding which real force provides it, and how much is needed, explains why cars skid on bends, why race tracks are tilted and why roller-coaster riders stay in their seats upside down.
What keeps it turning?
The previous topic showed that an object in uniform circular motion accelerates towards the centre with \(a_c = v^2/r\). By Newton's second law, that acceleration needs a net force in the same direction, so a car on a bend, a satellite and a stone on a string all need a net force towards the centre of their circle. Without it, the first law takes over and the object carries on along the tangent. How big must that force be, and where does it come from?
The size of the centripetal force
Combine \(F_{\text{net}} = ma\) with the centripetal acceleration and you get the net inward force needed:
Its unit is the newton, and it always points towards the centre. In problems, take the direction towards the centre as positive, add up the components of all the real forces along that line, and set the total equal to \(mv^2/r\). The square still matters: doubling the speed on the same circle needs four times the inward force.
A role, not a new force
Centripetal force is not an extra force of nature; it is a job that real forces do. On a whirled ball, tension does it. On a car on a flat bend, sideways static friction from the road does it. On the Moon, gravity does it. On a rider pressed against the wall of a spinning drum, the normal force does it, and sometimes two forces share the job. So a free-body diagram never gets an extra arrow labelled "centripetal force"; you draw the real forces, and their net inward component is the centripetal force. There is also no real outward force on the object, a point the next topic explains.
Worked example: a puck on a string
A 0.250 kg puck slides on a frictionless, horizontal air table, tied by a 0.800 m string to a pin, at a steady 3.00 m/s. Find the tension. 1. The normal force balances gravity, so tension alone provides the centripetal force. 2. Apply \(T = mv^2/r\): \(T = 0.250 \times 3.00^2/0.800\). 3. That gives \(T = 2.81\) N, directed along the string towards the pin. 4. Check the scaling: at 6.00 m/s the tension would be \(2^2 = 4\) times larger, 11.3 N. This is why a string that copes at a gentle speed can snap when the puck is sent round faster.
Turning on a flat road
On a level bend the only horizontal force on a car is static friction from the road, acting sideways on the tyres towards the centre. It is static, not kinetic, because the tyres are not sliding sideways. Static friction has a maximum, \(f_s \le \mu_s F_N\), and on level ground \(F_N = mg\). The car holds the curve only if \(mv^2/r \le \mu_s mg\), which gives a top speed of
The mass cancels, so a lorry and a small car share the same limit. A wet or icy road lowers \(\mu_s\), and the safe speed with it.
Worked example: a car on a level bend
A 1200 kg car rounds a level bend of radius 45.0 m at 14.0 m/s. Find the friction force needed and the smallest coefficient of static friction that will do. 1. Acceleration: \(a_c = 14.0^2/45.0 = 4.356\) m/s². 2. Force: \(f = ma_c = 1200 \times 4.356 = 5.23 \times 10^3\) N, towards the centre. 3. Coefficient: \(\mu_s \ge a_c/g = 4.356/9.80 = 0.444\). Dry concrete, at about 1.0, manages this easily. 4. On a slushy road with \(\mu_s = 0.30\), the top speed is \(\sqrt{0.30 \times 9.80 \times 45.0} = 11.5\) m/s, so the driver must slow down. 5. Check: 11.5 m/s is below 14.0 m/s, as a lower coefficient requires.
Banked curves
Tilting a road towards the centre lets the normal force help. Picture an ideal, frictionless bank at angle \(\theta\). The normal force is at right angles to the road surface, so it tilts inwards by \(\theta\). Its vertical component balances the weight, \(F_N\cos\theta = mg\), and its horizontal component provides the centripetal force, \(F_N\sin\theta = mv^2/r\). Dividing the two equations gives
At this design speed a car needs no friction at all. Faster, and friction must act down the slope to supply the extra inward force; slower, and friction must act up the slope to stop the car sliding inwards.
Worked example: designing a banked bend
Engineers want cars to take a bend of radius 120 m at 20.0 m/s with no help from friction. What bank angle is needed? 1. Use \(\tan\theta = v^2/(rg)\). 2. Substitute: \(\tan\theta = 20.0^2/(120 \times 9.80)\), which is 0.3401. 3. Take the inverse tangent: \(\theta = 18.8°\). 4. Check: the inward part of the normal force is \(mg\tan\theta = 0.3401 \times 9.80m = 3.33m\), and the needed \(mv^2/r = 400m/120 = 3.33m\). The mass cancels, so the angle suits every vehicle at that speed.
Vertical circles and loop-the-loops
In a vertical loop the speed changes, but at every point the net force towards the centre is \(mv^2/r\) for the speed at that instant. At the top, the weight and the track's normal force both point down, towards the centre:
The slowest speed that keeps the car on the track makes \(F_N = 0\), so gravity alone provides the centripetal force and \(v_{\min} = \sqrt{gr}\). Any slower and the car leaves the track. At the bottom, the normal force points up and the weight down, so \(F_N - mg = mv^2/r\) and the normal force exceeds the weight: riders feel heavier.
Worked example: the top of a loop
A roller-coaster loop has a radius of 8.00 m at the top, treated as part of a circle. A 60.0 kg rider passes the top, upside down, at 12.0 m/s. Find the seat's force and the minimum safe speed. 1. Take down, towards the centre, as positive: \(F_N + mg = mv^2/r\). 2. Rearrange:
3. So \(F_N = 492\) N, pressing down on the rider, less than their weight of 588 N. 4. Minimum speed: \(v_{\min} = \sqrt{9.80 \times 8.00} = 8.85\) m/s. 5. Check: 12.0 m/s is above 8.85 m/s, so N should be positive, and it is.
Common mistakes to avoid
First, drawing a centripetal force on a free-body diagram as well as the real forces, which counts the same push twice. Second, drawing an outward force on the object; in the ground frame there is none. Third, using kinetic friction for a car turning without skidding; it is static. Fourth, forgetting that \(\mu_s mg\) is the maximum friction available, not the friction that always acts. Fifth, getting signs wrong at the top or bottom of a loop: take towards the centre as positive every time. Sixth, forgetting the square on \(v\), or the root in \(\sqrt{gr}\).
Key takeaways
Circular motion needs a net inward force, F_c = mv²/r = mrω², directed towards the centre. It is supplied by real forces: tension, friction, gravity, the normal force or a combination. On a level bend, static friction limits the speed to v_max = √(μ_s gr). On an ideal frictionless bank, tan θ = v²/(rg) at the design speed. At the top of a vertical loop, F_N + mg = mv²/r, so the minimum speed is √(gr); at the bottom, F_N − mg = mv²/r and riders feel heavier.
Flashcards
Flashcard
The net force towards the centre needed for circular motion
Test your understanding
Question 1 of 5
A 0.500 kg ball slides in a horizontal circle of radius 1.50 m on a frictionless table, tied to a central pin, moving at 4.00 m/s. Find the tension in the string.
Question 2 of 5
A level bend has a radius of 30.0 m, and the coefficient of static friction between tyres and road is 0.500. What is the fastest speed at which a car can take the bend?
Question 3 of 5
A frictionless curve of radius 80.0 m is to be taken at 15.0 m/s. What bank angle is needed?
Question 4 of 5
A cart goes round a vertical loop of radius 5.00 m. What is the minimum speed at the top for it to stay on the track?
Question 5 of 5
Which statement about centripetal force is correct?
