Physics › Section H · Fluids › Topic H.5
Flow rate and continuity
Water racing out of a hose nozzle, a river slowing as it widens into a lake and blood creeping through capillaries all follow one rule: for a liquid, whatever flows in must flow out. This topic turns that rule into the continuity equation.
From still fluids to moving ones
The previous topics dealt with fluids at rest. Fluid dynamics deals with fluids that move. A useful picture is the streamline, the path traced by a small parcel of fluid. In steady flow the speed and direction at any fixed point do not change with time, so the streamlines stay put, like lanes on a road. Where streamlines crowd together the fluid moves faster. We also treat the fluid as incompressible, meaning its density stays constant, which is an excellent approximation for liquids.
Volume flow rate
The volume flow rate \(Q\) is the volume of fluid that passes a given point per unit time:
Its SI unit is the cubic metre per second, \(\text{m}^3/\text{s}\), but litres are often handier. One litre is \(10^{-3}\ \text{m}^3\), or 1000 cm³, so 1 L/s is \(10^{-3}\ \text{m}^3/\text{s}\). A resting adult's heart, for example, pumps roughly 5 L of blood per minute. Flow rate tells you how much fluid moves, not how fast any one parcel of it travels.
Flow rate and speed: Q = Av
Picture fluid moving at average speed \(v\) along a pipe of cross-sectional area \(A\). In time \(t\), the fluid that passes a point fills a cylinder of length \(vt\), so its volume is \(Avt\). Dividing by \(t\) gives
A fast mountain stream can carry far less water than a broad, slow river, because the river's cross-section is so much larger. Here \(v\) is the average speed across the section; real fluids move faster in the middle of a pipe than near its walls, as a later topic shows.
Worked example: filling a paddling pool
A garden hose has an inner radius of 0.800 cm, and water moves along it at an average speed of 1.50 m/s. How long does it take to put 150 L of water in a paddling pool? 1. Convert to SI: \(r = 0.00800\) m. 2. Area:
3. Flow rate: \(Q = Av = 3.016 \times 10^{-4}\ \text{m}^3/\text{s}\), which is 0.302 L/s. 4. Time: \(t = V/Q = 150 \div 0.3016 = 497\) s, about 8.3 minutes. 5. Check the units: \(\text{m}^2 \times \text{m/s}\) gives \(\text{m}^3/\text{s}\), and litres divided by litres per second gives seconds.
The continuity equation
Suppose a liquid flows steadily through a pipe with no leaks and no side branches. Liquid cannot pile up or vanish anywhere in between, so every second the same volume must pass every cross-section. For any two points 1 and 2,
This is the continuity equation, a statement of conservation of mass for an incompressible fluid. Where the pipe narrows, the fluid speeds up; where it widens, the fluid slows. For a circular pipe \(A = \pi r^2\), so the speed depends on the inverse square of the radius: halve the diameter and the speed rises by a factor of four, not two.
Worked example: a hose nozzle
The hose from the previous example, inner radius 0.800 cm, carries water at 1.50 m/s into a nozzle of inner radius 0.200 cm. Find the speed in the nozzle and check the flow rate. 1. Rearrange continuity: \(v_2 = v_1 \frac{A_1}{A_2} = v_1 \left(\frac{r_1}{r_2}\right)^2\), since \(\pi\) cancels. 2. Ratio of radii: \(0.800 \div 0.200 = 4.00\), so the area ratio is 16.0. 3. Speed: \(v_2 = 1.50 \times 16.0 = 24.0\) m/s. 4. Check:
the same as in the hose, as continuity demands. The nozzle adds no water; it squeezes the same flow through a smaller hole.
Continuity in everyday life
Press your thumb over the end of a hose so the opening shrinks to a quarter of its area, and the water leaves about four times faster, provided the flow rate stays about the same. In practice the flow rate drops somewhat, because the narrow opening resists the flow, but the jet still speeds up a lot. A river runs quickly through a narrow gorge and slows where it spreads into a wide lake. Blowing through pursed lips makes a fast jet that can put out a candle, while the same breath through a wide-open mouth barely moves the flame.
Branching flows
When one pipe splits into several, continuity still holds, but for the total. The flow into the junction equals the sum of the flows out of it. If one tube feeds \(n\) identical branches, each of area \(A_2\), then
What counts is the combined area of all the branches. Many narrow branches can add up to far more area than the single tube feeding them, and then the fluid slows down even though each branch is narrow. Your circulatory system works this way.
Worked example: from aorta to capillaries
A heart pumps 6.0 L/min into an aorta of radius 1.2 cm. Blood in the capillaries moves at about 0.50 mm/s, and a typical capillary has a radius of 4.0 µm. Estimate the speed in the aorta and the number of capillaries. 1. Flow rate: 6.0 L per 60 s is \(1.0 \times 10^{-4}\ \text{m}^3/\text{s}\). 2. Aorta:
3. Total capillary area:
4. One capillary has area \(\pi r^2 = 5.03 \times 10^{-11}\ \text{m}^2\), so
5. Check: the blood slows by a factor of \(0.22 \div 0.00050 \approx 440\), so the total capillary area should be about 440 times the aorta's \(4.5 \times 10^{-4}\ \text{m}^2\), and it is.
What about gases?
Gases are compressible, so the volume form of continuity needs care. What is always conserved in steady flow is the mass flow rate, the mass passing a point per second, \(\rho A v\):
For a liquid, \(\rho_1 = \rho_2\) and this reduces to \(A_1 v_1 = A_2 v_2\). Air moving well below about a third of the speed of sound changes its density by only a few percent, so \(A_1 v_1 = A_2 v_2\) works well for ventilation ducts and breathing. For jet engines, the density change must be included.
Common mistakes to avoid
First, confusing flow rate with speed: a wide, slow river can carry more water than a fast, narrow stream. Second, using the diameter in \(A = \pi r^2\) instead of the radius, which makes the area four times too large. Third, forgetting the square: halving a pipe's radius quadruples the speed, it does not double it. Fourth, mixing litres, cm² and m² in one calculation; convert to SI first. Fifth, applying \(A_1 v_1 = A_2 v_2\) to a single branch of a split pipe, when it is the total area of all the branches that counts.
Key takeaways
Volume flow rate is volume per unit time, Q = V/t, in cubic metres per second or litres per second, with 1 L = 10⁻³ m³. It is related to the average speed by Q = Av. For an incompressible fluid in steady flow, continuity gives A₁v₁ = A₂v₂: narrower means faster, and for a round pipe the speed varies as one over the radius squared. When a flow branches, the total area of the branches counts. For gases, the mass flow rate ρAv is conserved; slow-moving air is nearly incompressible.
Flashcards
Flashcard
The physics of moving fluids
Test your understanding
Question 1 of 5
Water flows at 1.5 m/s through a pipe of diameter 4.0 cm, which narrows to a diameter of 2.0 cm. What is the speed in the narrow section?
Question 2 of 5
Water moves at an average speed of 2.0 m/s through a pipe of radius 1.0 cm. What is the volume flow rate?
Question 3 of 5
A tap fills a 60 L tank at a steady 0.25 L/s. How long does it take?
Question 4 of 5
A pipe of area 12 cm² carries water at 3.0 m/s and splits into 4 identical branches, each of area 2.0 cm². What is the speed in each branch?
Question 5 of 5
A fast, narrow mountain stream and a slow, wide river are compared. Which statement must be true?
