Physics › Section P · Magnetism › Topic P.3

The Hall effect and force on a wire

Charges drifting along a wire feel the same magnetic force as charges flying through empty space. Inside the wire that force produces a small sideways voltage, the Hall effect, and it also pushes the wire itself, which is how loudspeakers and motors work.

Moving charges inside a conductor

The previous topic found the force \(F = qvB\sin\theta\) on a charge moving freely through a magnetic field. A current in a wire is also moving charge: free electrons drifting slowly along it, as the current topic showed. A field across the wire pushes every one of those carriers sideways. Two things follow. The carriers crowd towards one side of the conductor, creating a small voltage across it, the Hall effect. And because the carriers cannot leave the wire, their sideways push is passed on to the wire itself, so the whole wire feels a force.

The Hall effect

Picture a flat strip carrying a current along its length, with a magnetic field at right angles to its face. The drifting carriers are pushed towards one edge. Charge builds up there, leaving the opposite edge with the opposite charge, and this separation sets up an electric field across the strip. The build-up stops when the electric force on each carrier balances the magnetic force:

qE = qvB \quad\Rightarrow\quad E = vB

where \(v\) is the drift speed. Balance is reached almost instantly. The voltage across the strip is the Hall emf, discovered by Edwin Hall in 1879. For a uniform field across a strip of width \(w\), \(E = V/w\) from the topic on uniform fields, so the Hall emf is \(\mathcal{E} = Bwv\).

What the Hall effect reveals

The sign of the Hall emf tells you the sign of the moving charges. A current to the right can be positive charges moving right or negative charges moving left, and the right-hand rule pushes both towards the same edge. So the edge that gains charge becomes negative if the carriers are electrons and positive if they are positive. Hall measurements confirmed that electrons carry the current in most metals, and showed that some semiconductors conduct mainly by positive carriers. Because \(E = vB\), measuring the Hall field also gives the drift speed, and from \(I = nqAv_d\) the number of carriers per cubic metre.

Worked example: the Hall emf in a copper strip

A copper strip 2.0 cm wide and 0.10 mm thick carries 20 A at right angles to a 1.2 T field. Copper has \(8.49 \times 10^{28}\) free electrons per cubic metre. Find the Hall emf. 1. Cross-section:

A = (0.020)(1.0 \times 10^{-4}) = 2.0 \times 10^{-6}\ \text{m}^2

2. Drift speed:

v_d = \frac{I}{nqA} = \frac{20}{(8.49 \times 10^{28})(1.602 \times 10^{-19})(2.0 \times 10^{-6})}

which is \(7.4 \times 10^{-4}\) m/s. 3. Hall field: \(E = vB = 8.8 \times 10^{-4}\) V/m. 4. Hall emf: \(\mathcal{E} = Ew\), which is \(1.8 \times 10^{-5}\) V, about 18 μV. Check: metals have huge \(n\), so drift and Hall emf are tiny; semiconductors, with far fewer carriers, give much larger Hall voltages, which is why Hall sensors use them.

Hall probes and flow meters

A Hall probe is a small semiconductor chip carrying a known current. Its Hall emf is proportional to the field, so once calibrated it measures \(B\) directly, and it can be made tiny enough to map a field point by point. Phones use Hall sensors to detect the magnet in a flip cover, and cars use them to sense the position of rotating shafts. The same principle measures the flow of any liquid containing ions, such as blood. A field across a vessel pushes positive and negative ions to opposite sides, giving a voltage \(\mathcal{E} = Bdv\) across the diameter \(d\), so the average flow speed \(v\) can be found without anything entering the vessel.

Force on a current-carrying wire

Add up the forces on all the carriers in a straight wire of length \(l\) and cross-section \(A\) in a uniform field. There are \(nAl\) carriers, each feeling \(qv_dB\sin\theta\), all in the same direction, so the total is \(nAlqv_dB\sin\theta\). Since \(I = nqAv_d\), this collapses to

F = IlB\sin\theta

where \(\theta\) is the angle between the wire, taken in the direction of the current, and the field. The direction comes from the same right-hand rule, with your thumb along the current: fingers along the field, and the force comes out of your palm. A wire along the field feels no force.

Worked example: a wire in a magnet's gap

A straight wire carries 12 A due east through a uniform horizontal field of 0.080 T pointing due north. The length of wire in the field is 0.50 m. Find the force. 1. The current and field are at 90°, so \(\sin\theta = 1\). 2. Magnitude:

F = IlB = (12)(0.50)(0.080) = 0.48\ \text{N}

3. Direction: thumb east, fingers north; the palm faces up, so the force is vertically upwards. 4. Check the units: amperes times metres times teslas give newtons, because 1 T = 1 N/(A·m). Reversing either the current or the field would reverse the force, making it point down.

Worked example: a floating wire

A horizontal copper rod of mass per metre 0.0150 kg/m sits at right angles to a horizontal 0.050 T field. What current makes the magnetic force hold it up against gravity? Take g = 9.80 m/s². 1. For balance the upward magnetic force equals the weight: \(IlB = mg\). 2. Divide by \(l\):

I = \frac{(m/l)g}{B} = \frac{(0.0150)(9.80)}{0.050} = 2.9\ \text{A}

3. Direction: for an upward force with the field pointing north, the current must run east, as in the previous example. 4. Check: doubling the field would halve the current needed, and the length cancels, so a longer rod needs the same current.

Wires at work

A loudspeaker has a coil attached to a paper or plastic cone, sitting in the gap of a strong permanent magnet. An audio current alternating in the coil pushes it back and forth, and the cone sends out sound waves. Magnetohydrodynamic pumps pass a current across a conducting liquid, such as the liquid sodium coolant of some nuclear reactors, at right angles to a field; the force on the current drives the liquid along a pipe with no moving parts. Earth's field also acts on power lines, but weakly: a 100 A line at right angles to a \(5 \times 10^{-5}\) T field feels only 0.005 N per metre.

Common mistakes to avoid

First, getting the Hall emf sign wrong by forgetting that electrons drift opposite to the conventional current while still being pushed to the same edge as positive carriers would be. Second, putting the current or the speed of a free particle into \(E = vB\); the \(v\) is the slow drift speed. Third, measuring \(\theta\) in \(F = IlB\sin\theta\) from the wrong line: it is between the wire and the field. Fourth, using the whole wire's length rather than the length actually inside the field. Fifth, forgetting \(g\) when balancing a magnetic force against a weight.

Key takeaways

A field across a current-carrying conductor pushes the carriers to one side until the electric force balances the magnetic force, so E = vB, and the Hall emf across a width w is Bwv. Its sign reveals the sign of the carriers; Hall probes measure B, and the same idea measures blood flow. Summing the forces on the carriers gives the force on a wire, F = IlB sin θ, with θ between the current and the field and the direction given by the right-hand rule with the thumb along the current. These forces drive loudspeakers and magnetohydrodynamic pumps.

Flashcards

Flashcard

Hall effect

A sideways voltage across a current-carrying conductor in a magnetic field

Edwin Hall, 1879.

Test your understanding

Question 1 of 5

A 0.40 m length of wire carrying 8.0 A lies at 60° to a uniform 0.25 T field. What is the magnetic force on it?

Question 2 of 5

What can the sign of the Hall emf across a conductor tell you?

Question 3 of 5

Charge carriers drift at 5.0 × 10⁻⁴ m/s through a strip at right angles to a 1.5 T field. What is the Hall electric field once the forces balance?

Question 4 of 5

A horizontal wire carries current due north through a magnetic field that points vertically upwards. Which way is the force on the wire?

Question 5 of 5

A horizontal rod of mass per metre 0.020 kg/m lies at right angles to a horizontal 0.40 T field. What current makes the magnetic force support its weight? (g = 9.80 m/s²)

← Previous topicNext topic →