Physics › Section P · Magnetism › Topic P.4

Torque on a current loop: motors and meters

Put a loop of current in a magnetic field and the forces on its sides do not push it anywhere: they twist it. That twist turns every electric motor, from a phone's vibration buzzer to a train, and swings the needle of an analogue meter.

From a straight wire to a loop

The previous topic found the force on a straight wire, \(F = IlB\sin\theta\). Now bend the wire into a rectangular loop, mount it on an axle and place it in a uniform field. Current flows one way along one side of the loop and the opposite way along the other, so the forces on those two sides point in opposite directions. They cancel as forces, but because they act along different lines they produce a torque, the turning effect met in the topics on equilibrium and rotation. Electric motors and analogue meters are both built on this torque.

Finding the torque

Take a rectangular loop with sides of length \(l\) parallel to a vertical axle and sides of width \(w\) across it, in a horizontal field. The forces on the top and bottom sides are vertical, along the axle, so they give no torque, and they cancel. Each long side carries current at right angles to the field, so it feels \(F = IlB\), sideways, at a distance \(w/2\) from the axle. Let \(\theta\) be the angle between the field and the normal, the line perpendicular to the plane of the loop. Each force then gives a torque \(F(w/2)\sin\theta\), both in the same sense, so the total is \(IlwB\sin\theta\). Since \(lw\) is the area \(A\) of the loop, the torque is \(IAB\sin\theta\).

The torque equation

A coil of \(N\) turns multiplies the torque by \(N\):

\tau = NIAB\sin\theta

Here \(\theta\) is measured between the field and the normal to the coil, not between the field and the plane of the coil. The result holds for a flat loop of any shape, circular or rectangular, in a uniform field. The net force on the loop is zero: a uniform field turns a current loop but does not move it bodily. The unit works out as A·m²·T, which equals N·m, because 1 T = 1 N/(A·m).

Maximum, zero and reversed torque

The torque is largest, \(NIAB\), when \(\theta = 90^\circ\): the plane of the coil lies along the field. It is zero when \(\theta = 0\): the plane of the coil is perpendicular to the field. The forces are then still there, but they pull outwards along the plane of the loop, through the axle, and cannot turn it. This is the coil's stable equilibrium position; at \(\theta = 180^\circ\) the torque is also zero, but that balance is unstable. If the coil swings past \(\theta = 0\), \(\sin\theta\) changes sign and the torque reverses, pulling the coil back. Left alone, a coil with steady current simply rocks to and fro about equilibrium and settles there, like a compass needle lining up with a field.

Worked example: torque on a motor coil

A rectangular coil of 200 turns, 5.0 cm by 8.0 cm, carries 2.5 A in a uniform 0.30 T field. Find the maximum torque, and the torque when the normal is at 30° to the field. 1. Area:

A = (0.050)(0.080) = 4.0 \times 10^{-3}\ \text{m}^2

2. Maximum torque, at \(\theta = 90^\circ\):

\tau_{\max} = (200)(2.5)(4.0 \times 10^{-3})(0.30) = 0.60\ \text{N}\cdot\text{m}

3. At \(\theta = 30^\circ\): \(\tau = 0.60 \sin 30^\circ = 0.30\) N·m. 4. Check another way: each 8.0 cm side of the 200 turns feels \(F = NIlB = 12\) N, at 2.5 cm from the axle, so

\tau_{\max} = 2(12\ \text{N})(0.025\ \text{m}) = 0.60\ \text{N}\cdot\text{m}

in agreement.

Keeping a motor turning

To make a coil spin continuously, the torque must keep the same sense, so the current must reverse each time the coil passes equilibrium. A simple direct-current motor does this with a commutator: a split ring on the axle, each half joined to one end of the coil. Fixed carbon brushes press on the ring and feed in the current. Every half turn the gaps pass the brushes, the coil's connections swap and the current in the coil reverses. The coil's momentum carries it through the zero-torque point, and the reversed current drives it on round. Practical motors use many coils at different angles wound on an iron core, so the torque is strong and nearly steady, and electrical energy is converted to mechanical work.

Analogue meters

The galvanometer at the heart of the analogue ammeters and voltmeters of the topic on meters and null measurements is a coil that turns only part of a revolution. Its magnet has curved pole pieces round a fixed iron cylinder, which make the field radial: it points along the plane of the coil wherever the coil turns, so \(\sin\theta = 1\) throughout the scale. The torque is then \(NIAB\), proportional to the current. A fine spring supplies a restoring torque proportional to the angle turned, and the needle stops where the two balance. The deflection is therefore proportional to the current, giving an evenly spaced scale. Many turns, a large area, a strong field and a weak spring make a sensitive meter.

Worked example: a galvanometer's spring

A galvanometer coil has 100 turns, each 1.2 cm by 2.0 cm, in a radial field of 0.20 T. It must swing 90° at a full-scale current of 50.0 μA. 1. Area:

A = (0.012)(0.020) = 2.4 \times 10^{-4}\ \text{m}^2

2. Torque at full scale, with \(\sin\theta = 1\):

\tau = (100)(50.0 \times 10^{-6})(2.4 \times 10^{-4})(0.20)

which is \(2.4 \times 10^{-7}\) N·m. 3. The spring must give this torque at 90°, or \(\pi/2\) rad, so its torque per radian is

\frac{2.4 \times 10^{-7}}{\pi/2} = 1.5 \times 10^{-7}\ \text{N}\cdot\text{m/rad}

4. Check: at 25.0 μA the magnetic torque halves, so the needle stops at 45°, halfway across an even scale.

Common mistakes to avoid

First, measuring \(\theta\) from the plane of the coil instead of from its normal, which swaps the maximum and zero positions. Second, forgetting \(N\), or using the length of a side where the area belongs. Third, leaving dimensions in centimetres: 5.0 cm by 8.0 cm is \(4.0 \times 10^{-3}\ \text{m}^2\), not 40. Fourth, thinking a uniform field pushes the whole loop along; the net force is zero and only a torque remains. Fifth, believing the commutator makes the torque constant; it only keeps the torque from reversing.

Key takeaways

In a uniform field the forces on opposite sides of a current loop cancel as forces but give a torque, τ = NIAB sin θ, where θ is between the field and the normal to the coil. The torque is greatest when the coil's plane lies along the field and zero when it is perpendicular, and it reverses past that equilibrium. A DC motor uses a commutator and brushes to reverse the current every half turn so the coil keeps turning. A galvanometer uses a radial field, so the torque is proportional to the current, balanced by a spring to give a deflection proportional to I.

Flashcards

Flashcard

τ = NIAB sin θ

Torque on a flat coil in a uniform field

θ is between B and the normal to the coil.

Test your understanding

Question 1 of 5

A square coil of 50 turns, 4.0 cm on each side, carries 3.0 A in a uniform 0.50 T field. What is the maximum torque on it?

Question 2 of 5

In which position does a current-carrying coil in a uniform field feel zero torque?

Question 3 of 5

What is the job of the commutator in a simple DC motor?

Question 4 of 5

A coil feels a maximum torque of 0.80 N·m. What torque does it feel when the normal to the coil is at 30° to the field, with the same current?

Question 5 of 5

Why does a galvanometer use curved pole pieces that make the field radial?

← Previous topicNext topic →