Physics › Section Q · Electromagnetic induction and AC circuits › Topic Q.5

Inductance, RL circuits, and AC circuits

A coil resists any change in the current through it, just as a mass resists changes in its velocity. That property, inductance, combines with resistance and capacitance to decide how circuits respond to switching and to alternating current, and it is how a radio picks out one station.

Coils that oppose change

Earlier topics induced an emf by changing the flux from a magnet or another coil. Two coils placed close together show mutual inductance: a changing current \(I_1\) in one induces an emf in the other, \(\mathcal{E}_2 = -M\Delta I_1/\Delta t\), where \(M\) depends on the coils' shapes and spacing. Transformers and GFCIs rely on it. But a single coil also threads its own field through its turns. When its current changes, its own flux changes, and Faraday's law induces an emf in the coil itself. By Lenz's law that emf opposes the change: it pushes back against a rising current and tries to keep a falling one going. This is self-inductance, and a coil used for it is called an inductor.

Self-inductance and stored energy

The self-induced emf is proportional to how fast the current changes:

\mathcal{E} = -L\frac{\Delta I}{\Delta t}

The constant \(L\) is the inductance, set by the coil's turns, size and core. Its unit is the henry, \(1\ \text{H} = 1\ \text{V}\cdot\text{s/A}\); an iron core raises \(L\) greatly. Building up a current in an inductor takes work against this emf, and that energy is stored in the magnetic field:

E = \tfrac{1}{2}LI^2

This parallels \(\tfrac{1}{2}CV^2\) for a capacitor. A steady current induces nothing, so an inductor carrying steady DC acts as a plain wire with only its small resistance.

Worked example: switching off an inductor

A 0.250 H inductor carries 3.00 A. A switch interrupts the current, which falls to zero in 2.00 ms. Find the average self-induced emf and the energy that was stored. 1. Change in current: \(\Delta I = 0 - 3.00 = -3.00\) A. 2. Emf:

\mathcal{E} = -L\frac{\Delta I}{\Delta t} = -(0.250)\frac{-3.00\ \text{A}}{2.00 \times 10^{-3}\ \text{s}} = 375\ \text{V}

positive, so it acts to keep the current flowing. 3. Energy: \(\tfrac{1}{2}(0.250)(3.00)^2\), which is 1.13 J. 4. Check: a modest current stopped quickly gives hundreds of volts, which is why switches on inductive loads can spark, and how a car's ignition coil makes the high voltage for its spark plugs.

RL circuits

Connect an inductor \(L\) and resistor \(R\) in series to a battery of emf \(\mathcal{E}\). The current cannot jump to \(\mathcal{E}/R\), because the inductor's emf opposes the rise. Stated without proof, it grows as

I = \frac{\mathcal{E}}{R}\left(1 - e^{-t/\tau}\right), \qquad \tau = \frac{L}{R}

The time constant \(\tau = L/R\) is in seconds, since \(1\ \text{H}/\Omega = 1\) s. If the battery is then replaced by a wire, the current decays as \(I = I_0e^{-t/\tau}\). These are the same shapes as the RC circuit topic: after one time constant the rise reaches 63.2% of its final value and a decay leaves 36.8%. In an RL circuit it is the current that changes gradually, where in an RC circuit it was the capacitor's voltage.

Worked example: an RL circuit switching on

A 12.0 V battery is switched across a 0.200 H inductor in series with a 4.00 Ω resistor. Find the time constant, the final current, the current after 0.100 s, and when the current reaches 2.00 A. 1. \(\tau = L/R = 0.200/4.00\), which is 0.0500 s. 2. Final current: \(\mathcal{E}/R = 3.00\) A. 3. At 0.100 s, which is \(2\tau\):

I = 3.00\left(1 - e^{-2}\right) = 3.00 \times 0.865 = 2.59\ \text{A}

4. For 2.00 A: \(1 - e^{-t/\tau} = 2/3\), so \(e^{-t/\tau} = 1/3\), and \(t = \tau\ln 3 = 0.0549\) s. 5. Check: 2.00 A is 66.7% of the final value, just past the 63.2% reached at \(\tau\), and 0.0549 s is just past 0.0500 s.

Reactance

With AC, an inductor faces a current that changes all the time, so its emf opposes the current continually. This opposition is its inductive reactance, and it grows with frequency: \(X_L = 2\pi fL\). A capacitor does the reverse. At low frequency it has time to charge fully and block the current, so its capacitive reactance falls as frequency rises:

X_C = \frac{1}{2\pi fC}

Both are in ohms, and for either one \(I_{\text{rms}} = V_{\text{rms}}/X\). They also shift the timing. In an inductor the current peaks a quarter cycle after the voltage: it lags by 90°. In a capacitor the current peaks a quarter cycle before: it leads by 90°. Inductors pass low frequencies; capacitors pass high ones.

Impedance and resonance

In a series RLC circuit the same current flows through all three parts, but their voltages peak at different times, so they cannot simply be added. The total opposition, the impedance \(Z\) in ohms, is

Z = \sqrt{R^2 + (X_L - X_C)^2}

and \(I_{\text{rms}} = V_{\text{rms}}/Z\). The inductive and capacitive reactances partly cancel, because their voltages are always opposite. When \(X_L = X_C\) they cancel completely, \(Z = R\), and the current is largest. That happens at the resonant frequency:

f_0 = \frac{1}{2\pi\sqrt{LC}}

A radio tunes to a station by adjusting \(C\) or \(L\) until \(f_0\) matches that station's frequency, so its signal produces a large current while others do not.

Power factor

Inductors and capacitors store energy for part of each cycle and give it back, so on average they consume none; only the resistance dissipates power. The average power is

P_{\text{ave}} = I_{\text{rms}}V_{\text{rms}}\cos\phi, \qquad \cos\phi = \frac{R}{Z}

where \(\phi\) is the phase angle between current and voltage, and \(\cos\phi\) is the power factor. For a pure resistor, or any circuit at resonance, \(\cos\phi = 1\). For a nearly pure inductor or capacitor it is close to 0. Utilities prefer large motor loads to have a power factor near 1, because a low one means extra current, and extra line loss, for the same useful power.

Worked example: a series RLC circuit

A 40.0 Ω resistor, a 50.0 mH inductor and a 10.0 μF capacitor are in series across 120 V rms at 60.0 Hz. 1. Reactances: \(X_L = 2\pi(60.0)(0.0500)\), which is 18.8 Ω, and

X_C = \frac{1}{2\pi(60.0)(10.0 \times 10^{-6})} = 265\ \Omega

2. Impedance:

Z = \sqrt{40.0^2 + (18.85 - 265.3)^2} = 249.6\ \Omega

3. Current: \(I = 120/249.6 = 0.481\) A. 4. Power factor: \(40.0/249.6 = 0.160\), so \(P = 120 \times 0.481 \times 0.160 = 9.24\) W. 5. Check: \(I^2R = (0.481)^2(40.0) = 9.24\) W. 6. Resonance:

f_0 = \frac{1}{2\pi\sqrt{(0.0500)(10.0 \times 10^{-6})}} = 225\ \text{Hz}

where \(Z = R\), the current is 3.00 A and the power is 360 W.

Common mistakes to avoid

First, writing the RL time constant as \(LR\) or \(R/L\); it is \(L/R\). Second, adding \(R\), \(X_L\) and \(X_C\) directly instead of using the square-root formula. Third, forgetting the \(2\pi\) in reactances or in \(f_0\), or putting μF and mH in without converting. Fourth, mixing up the trends: \(X_L\) rises with frequency and \(X_C\) falls. Fifth, calculating AC power as \(I_{\text{rms}}V_{\text{rms}}\) without the power factor when the circuit is not purely resistive.

Key takeaways

A changing current induces an emf in a nearby coil (mutual inductance) and in its own coil: emf = −L ΔI/Δt, with L in henries. An inductor stores energy ½LI². In an RL circuit the current rises as (ε/R)(1 − e^(−t/τ)) or decays as I₀e^(−t/τ), with τ = L/R. Reactances are X_L = 2πfL and X_C = 1/(2πfC). A series RLC circuit has Z = √(R² + (X_L − X_C)²), and resonance at f₀ = 1/(2π√(LC)), where Z = R. Average power is I_rms V_rms cos φ, with power factor cos φ = R/Z.

Flashcards

Flashcard

Mutual inductance, M

emf₂ = −M ΔI₁/Δt in a neighbouring coil

Used in transformers and GFCIs.

Test your understanding

Question 1 of 5

The current in a 0.40 H inductor changes steadily by 2.0 A in 0.010 s. What is the size of the self-induced emf?

Question 2 of 5

What is the time constant of a circuit with a 0.30 H inductor in series with a 6.0 Ω resistor?

Question 3 of 5

What is the reactance of a 20.0 μF capacitor at 50.0 Hz?

Question 4 of 5

What is the resonant frequency of a series circuit with a 10.0 mH inductor and a 1.00 μF capacitor?

Question 5 of 5

A series RLC circuit across 100 V rms has impedance 50 Ω and resistance 30 Ω. What average power does it use?

← Previous topicNext topic →