Physics › Section H · Fluids › Topic H.2

Pressure with depth, Pascal's principle, gauge pressure

Dive to the bottom of a pool and your ears tell you the pressure has risen. The same simple rule, that a fluid must hold up its own weight, explains water towers, car brakes, hydraulic lifts and the gauges used to read pressure.

Why pressure grows with depth

Picture a column of liquid of density \(\rho\), height \(h\) and cross-sectional area \(A\) standing on the floor of a tank. Its volume is \(Ah\), so its mass is \(\rho A h\) and its weight is \(\rho A h g\). The floor must support that weight, so the pressure on it from the liquid is the weight divided by the area:

P = \frac{\rho A h g}{A} = \rho g h

The area cancels, so only depth and density matter. The result holds anywhere in a still fluid, container or not, since the surrounding fluid must push equally hard to keep each point still. Water is about 830 times as dense as air, so a metre of diving changes the pressure on you more than a lift ride up a skyscraper.

Total pressure and container shape

If the surface of the liquid is open to the air, the atmosphere presses on it too, and the two pressures add:

P = P_0 + \rho g h

Here \(P_0\) is the surface pressure, about 101 kPa at sea level. The formula takes \(\rho\) as constant, which suits liquids well but air only over small heights. Setting \(\rho g h\) equal to 1 atm for water gives \(h = 101{,}325 \div (1000 \times 9.80) = 10.3\) m, so every 10.3 m of water adds one atmosphere. Because only depth matters, connected vessels of any shape fill to the same level, and the pressure at a given depth is the same under a narrow tube as under a wide tank. A water tower relies on this: its water level sets the pressure at every tap below it.

Worked example: a diver on a reef

A diver works 25.0 m down in seawater of density \(1025\ \mathrm{kg/m^3}\), with air pressure 101.3 kPa. Find the pressure from the water and the total pressure. 1. Pressure from the water: \(\rho g h = 1025 \times 9.80 \times 25.0 = 2.51 \times 10^5\) Pa, or 251 kPa. 2. Total: \(P = 101.3 + 251.1 = 352\) kPa. 3. In atmospheres: \(352 \div 101.3 = 3.48\) atm. 4. Check with the rule of thumb: 25 m is about 2.4 lots of 10.3 m, so the water adds about 2.4 atm, and adding the 1 atm from the air gives about 3.4 atm. The slightly higher exact answer comes from seawater being denser than fresh water.

Pascal's principle

Push on water in an open river and it flows away; in a sealed container it cannot escape. Pascal's principle, named after the French scientist Blaise Pascal (1623 to 1662), says that any change of pressure at one point of an enclosed, still fluid reaches every other point, and every wall, in full. Squeeze a sealed bottle of water and the pressure rises by the same amount throughout, not just under your fingers. It follows that pressures from separate sources simply add, which is what \(P = P_0 + \rho g h\) says: the air's push on the surface arrives undiminished at every depth.

Hydraulic systems

A hydraulic system uses an enclosed liquid, such as hydraulic oil or brake fluid, to transmit force. Two pistons of areas \(A_1\) and \(A_2\) at the same height share the same pressure, so

\frac{F_1}{A_1} = \frac{F_2}{A_2}

with friction neglected. The force is multiplied by the area ratio \(A_2/A_1\), the ideal mechanical advantage; for round pistons it is \((r_2/r_1)^2\), the square of the ratio of radii or diameters. There is no free energy. The liquid barely compresses, so the volume leaving one cylinder enters the other, \(A_1 d_1 = A_2 d_2\), and the small piston moves further by the same factor. The work, force times distance, is equal at both ends. Car brakes, lifts and excavators all work this way.

Worked example: a garage lift

A hydraulic lift has a small piston 2.00 cm in diameter and a large piston 30.0 cm in diameter. What force on the small piston holds up a 1500 kg car, and how far must the small piston move in total to raise the car by 0.200 m? Assume the pistons are level and friction is negligible. 1. Area ratio: \((30.0 \div 2.00)^2 = 15.0^2 = 225\). 2. The car's weight is \(1500 \times 9.80 = 14{,}700\) N, so \(F_1 = 14{,}700 \div 225 = 65.3\) N. 3. Volume moved is equal at both ends, so \(d_1 = 225 \times 0.200 = 45.0\) m, delivered by many short pump strokes. 4. Check the energy: \(14{,}700 \times 0.200 = 2940\) J out, and \(65.33 \times 45.0 = 2940\) J in.

Gauge pressure and absolute pressure

Most gauges read zero when open to the air. They show gauge pressure, the amount by which a pressure exceeds atmospheric pressure. The full pressure is the absolute pressure:

P_{\text{abs}} = P_g + P_{\text{atm}}

So a tyre gauge reading 220 kPa means about \(220 + 101 = 321\) kPa absolute, and a flat tyre still holds air at 1 atm while its gauge reads zero. Gauge pressure is negative below atmospheric, as in a straw while you sip. A gas cannot go below zero absolute pressure, a perfect vacuum, so its gauge pressure never falls below about −101 kPa.

Measuring pressure

An open-tube manometer is a U-shaped tube of liquid with one arm open to the air and the other connected to the system being tested. If the levels differ by \(h\), the gauge pressure is \(P_g = \rho g h\): positive if the liquid stands higher in the open arm, negative if lower. A mercury barometer is a sealed tube with a near vacuum above the mercury, so it reads absolute pressure, about 760 mm of mercury at sea level; hence the unit mmHg. Aneroid gauges use a flexible metal capsule or bellows to move a pointer. Blood pressure cuffs read gauge pressure in mmHg.

Worked example: a gas line manometer

A water manometer is connected to a household gas pipe. The water in the open arm stands 12.0 cm higher than in the arm joined to the pipe. Find the gauge and absolute pressures of the gas, taking the air pressure as 101.3 kPa. 1. The water is pushed up the open arm, so the gas pushes harder than the air and the gauge pressure is positive. 2. \(P_g = \rho g h = 1000 \times 9.80 \times 0.120 = 1176\) Pa, or 1.18 kPa. 3. Absolute: \(101.3 + 1.18 = 102.5\) kPa. 4. Check: 12 cm is about 1/86 of 10.3 m, so the gauge pressure should be about 1/86 of an atmosphere, \(101.3 \div 86 = 1.18\) kPa, in agreement.

Common mistakes to avoid

First, forgetting to add atmospheric pressure when the question asks for absolute pressure, or adding it when a gauge reading is wanted. Second, using depth in centimetres or density in \(\mathrm{g/cm^3}\) in \(\rho g h\); use metres and \(\mathrm{kg/m^3}\) to get pascals. Third, forgetting to square in a hydraulic problem: if diameters are given, the force ratio is the diameter ratio squared. Fourth, believing a hydraulic system creates energy; the larger force moves a proportionally smaller distance. Fifth, thinking a wider or fuller container gives more pressure at the same depth; only depth and density matter.

Key takeaways

In an open liquid, P = P₀ + ρgh; every 10.3 m of water adds about one atmosphere, whatever the container's shape. Pascal's principle: a pressure change in an enclosed fluid reaches every part in full, so pressures add. Hydraulics: F₁/A₁ = F₂/A₂, and A₁d₁ = A₂d₂, so force is multiplied but work is not. Absolute pressure = gauge + atmospheric. Manometers read gauge pressure as ρgh; a mercury barometer reads absolute pressure, about 760 mmHg at sea level.

Flashcards

Flashcard

P = ρgh

Pressure from the fluid above, at depth h

Use kg/m³, m/s² and m to get pascals.

Test your understanding

Question 1 of 5

A freshwater lake is 15.0 m deep, and the air pressure is 101 kPa. Taking g = 9.80 m/s², what is the absolute pressure at the bottom?

Question 2 of 5

In a hydraulic press, the small piston has a diameter of 1.0 cm and the large piston a diameter of 5.0 cm. A force of 200 N is applied to the small piston. What force does the large piston exert, ignoring friction?

Question 3 of 5

A tyre gauge reads 230 kPa on a day when atmospheric pressure is 101 kPa. What is the absolute pressure of the air in the tyre?

Question 4 of 5

Three open containers of different shapes, a narrow tube, a wide tank and a cone, are all filled with water to the same depth. How do the pressures at their bottoms compare?

Question 5 of 5

An open-tube mercury manometer (density 13,600 kg/m³) is connected to a tank. The mercury in the open arm stands 50.0 mm higher than in the arm joined to the tank. What is the tank's gauge pressure?

← Previous topicNext topic →